2007-2013 Highlander Kluger · Service Manual SUSPENSION & AXLE

INSTALLATION

Removal / installation · Vehicles built Aug 2008 – Jun 2010

Versions by build date: May 2007 – Jul 2008 Aug 2008 – Jun 2010 from Jul 2010

NOTICE:
When removing/installing the front lower suspension arm or related parts, make sure to inspect the suspension arm bolt as shown in the following procedure.


1. INSTALL FRONT LOWER SUSPENSION ARM
  1. Install the front lower arm bushing stopper to the front lower suspension arm.

  1. Install the front lower suspension arm to the front frame assembly with the 3 bolts and nut, but do not tighten them yet.

  1. C207937E01
    Measure the outer diameter of the washer on the bolt (3) indicated by *1 in the illustration. If the outer diameter is 32 mm (1.260 in.), replace the bolt with a type B bolt shown in the table below. If the washer outer diameter is 34 mm (1.338 in.), it is not necessary to replace the bolt.
    Bolt
    Part Number
    Washer Outer Diameter
    Type A
    90119-14116
    32 mm (1.260 in.)
    Type B
    90119-14140
    32 mm (1.260 in.)
    Type C
    90119-14126
    34 mm (1.338 in.)

    NOTICE:
    1. When removing/reinstalling the front lower suspension arm or related parts, make sure to inspect the bolt (3) in the illustration and , if necessary, replace it with a type B bolt shown in the above table.
    2. There is no difference of the washer outer diameter between type A and B so that they cannot be visually distinguished.

    HINT:
    If a type B bolt was installed in an earlier procedure, it is not necessary to replace it.

  1. Tighten the 3 bolts in numerical order shown in the illustration.

    Torque:
    Bolt 1, 2:
    200 N*m{ 2039 kgf*cm , 147 ft.*lbf }
    Bolt 3:
    135 N*m{ 1377 kgf*cm , 100 ft.*lbf }

    HINT:
    Start installing the bolts from the front side of the vehicle.


2. INSTALL FRONT FRAME ASSEMBLY

  1. Temporarily install the engine assembly with transaxle with the 9 nuts and 2 bolts.

    A172974E01

  1. A172975E01
    Tighten the 4 nuts.

    Torque:
    A:
    87 N*m{ 887 kgf*cm , 64 ft.*lbf }
    B:
    52 N*m{ 525 kgf*cm , 38 ft.*lbf }

  1. A172976E01
    Tighten the 4 nuts.

    Torque:
    A:
    95 N*m{ 969 kgf*cm , 70 ft.*lbf }
    B:
    87 N*m{ 887 kgf*cm , 64 ft.*lbf }

  1. A172977E01
    Tighten the 4 nuts.

    Torque:
    A:
    95 N*m{ 969 kgf*cm , 70 ft.*lbf }
    B:
    87 N*m{ 887 kgf*cm , 64 ft.*lbf }

  1. A171830
    Tighten the 2 bolts.

    Torque:
    78 N*m{ 795 kgf*cm , 58 ft.*lbf }

  1. A171835
    Connect the duty vacuum switching valve connector and clamp.

  1. Install the 5 hole plugs.

    A172972E01


3. REMOVE ENGINE HANGERS

  1. A129635E01
    Remove the 4 bolts and 2 engine hangers.


4. INSTALL POWER STEERING LINK ASSEMBLY

  1. C166343
    Install the power steering link assembly with the 2 bolts and 2 nuts.

    Torque:
    70 N*m{ 713 kgf*cm , 51 ft.*lbf }

    NOTICE:
    1. Make sure to tighten the bolts starting from the left side of the vehicle.
    2. Because the nut has its own stopper, do not turn the nut. Tighten the bolt with the nut fixed.


5. INSTALL FRONT STABILIZER BAR WITH FRONT STABILIZER LINK ASSEMBLY

6. INSTALL NO. 1 FRONT STABILIZER BRACKET LH

  1. C167140
    Install the No. 1 front stabilizer bracket LH to the front frame assembly with the 2 bolts.

    Torque:
    29 N*m{ 296 kgf*cm , 21 ft.*lbf }


7. INSTALL NO. 1 FRONT STABILIZER BRACKET RH

HINT:
Perform the same procedure as the LH side.


8. INSTALL ENGINE ASSEMBLY WITH TRANSAXLE

HINT:
Install engine assembly with transaxle (Click here).

← INSTALLATION (May 2007 – Jul 2008)INSTALLATION (from Jul 2010) →