2007-2013 Highlander Kluger · Service Manual SUSPENSION & AXLE

ADJUSTMENT

Removal / installation · Vehicles built May 2007 – Jul 2008

Versions by build date: May 2007 – Jul 2008 Aug 2008 – Jun 2010 from Jul 2010

NOTICE:
If the wheel alignment has been adjusted, and if suspension or underbody components have been removed/installed or replaced, be sure to perform the following initialization procedure in order for the system to function normally:
  1. Disconnect the cable from the negative battery terminal for more than 2 seconds.
  2. Reconnect the cable to the negative battery terminal.
  3. Perform zero point calibration of the yaw rate and acceleration sensor and test mode inspection.

HINT:
(Click here)


1. INSPECT TIRES
  1. Inspect the tires (Click here).


2. MEASURE VEHICLE HEIGHT

NOTICE:
  1. Before inspecting the wheel alignment, adjust the vehicle height to the specified value.
  2. Be sure to perform measurement on a level surface.
  3. If it is necessary to go under the vehicle for measurement, confirm that the parking brake is applied and the vehicle is secured with chocks.

  1. Bounce on the vehicle up and down at the corners to stabilize the suspension.

  1. C170367E01
    Measure the vehicle height.

    Measuring points:
    A:
    Ground clearance of front wheel center
    B:
    Ground clearance of No. 1 lower suspension arm bushing set bolt center
    C:
    Ground clearance of rear wheel center
    D:
    Ground clearance of strut rod set bolt center

    Vehicle height:
    Model
    Front A - B
    Rear C - D
    2WD
    118.2 mm (4.65 in.)
    34.9 mm (1.37 in.)
    4WD
    118.3 mm (4.66 in.)
    33.8 mm (1.33 in.)


3. INSPECT TOE-IN

C132438E09

Toe-in:
Item
Specified Condition
Toe-in (2WD)
(total)
C + D: 0°10' +/- 0°12' (0.17° +/- 0.2°)
B - A: 3.0 +/- 2.0 mm (0.12 +/- 0.08 in.)
Toe-in (4WD)
(total)
C + D: 0°8' +/- 0°12' (0.14° +/- 0.2°)
B - A: 3.0 +/- 2.0 mm (0.12 +/- 0.08 in.)

If toe-in is not within the specified range, adjust it at the rear No. 2 suspension arms.

HINT:
Measure "B - A" only when "C + D" cannot be measured.


4. ADJUST TOE-IN (for 2WD)

  1. C108453
    Measure the lengths of the right and left rear No. 2 suspension arms.

    Standard difference:
    1.5 mm (0.06 in.) or less

    If the left-right difference is larger than 1.5 mm (0.06 in.), adjust it by following the procedures below.

  1. C108452E01
    Loosen the 2 lock nuts.

  1. If the length difference between the left and right rear No. 2 suspension arm assemblies is not within the specified range, adjust it by following the procedures below.

    HINT:
    1. Try to adjust toe-in to the center of the specified range.
    2. One turn of each adjusting tube will adjust toe-in by approximately 11.1 mm (0.44 in.).


    1. If the toe-in measurement is greater than the specified range, extend the shorter rear No. 2 suspension arm assembly by rotating the adjusting tube in the direction of arrow B in the illustration.

    2. If the toe-in measurement is less than the specified range, shorten the longer rear No. 2 suspension arm assembly by rotating the adjusting tube in the direction of arrow A in the illustration.

    3. Measure the toe-in.

  1. Turn the right and left adjusting tubes by an equal amount to adjust toe-in.

  1. Tighten the 2 lock nuts.

    Torque:
    56 N*m{ 571 kgf*cm , 41 ft.*lbf }


5. ADJUST TOE-IN (for 4WD)

  1. C165907
    Measure the distance between each wheel disc and the center of the toe-adjusting cam, and then confirm that left and right distances are the same.

    Difference in the length of rear No. 2 suspension arms:
    1.0 mm (0.04 in.) or less

    If the left-right difference is larger than 1.0 mm (0.04 in.), adjust it by following the procedures below.

  1. Loosen the toe-adjust cam set nuts.

  1. Turn the adjust cams by an equal amount to adjust toe-in.

    HINT:
    1. Try to adjust toe-in to the center of the specified range.
    2. The toe-in will change by the following amount corresponding to each graduation of the cam.
      Approx. 3.3 mm (0.13 in.)

  1. Tighten the toe-adjust cam set nuts.

    Torque:
    100 N*m{ 1019 kgf*cm , 74 ft.*lbf }


6. INSPECT CAMBER
-
2WD
4WD
Right-left difference
Camber
-1°00' +/- 45' (-1.00° +/- 0.75°)
-0°36' +/- 45' (-0.60° +/- 0.75°)
45' (0.75°) or less

HINT:
Camber is not adjustable. If the measurement is not within the specified range, inspect the suspension parts for damage and/or wear, and replace them if necessary.


7. PLACE FRONT WHEELS FACING STRAIGHT AHEAD

8. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).

HINT:
Disconnect the cable from the negative battery terminal for more than 2 seconds.


9. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).


10. PERFORM YAW RATE SENSOR ZERO POINT CALIBRATION

HINT:
Perform yaw rate sensor zero point calibration (Click here).


11. CHECK STEERING ANGLE SENSOR ZERO POINT CALIBRATION

HINT:
Check steering angle sensor zero point calibration (Click here).

← ADJUSTMENT (from Jul 2010)ADJUSTMENT (Aug 2008 – Jun 2010) →