2007-2013 Highlander Kluger · Service Manual BODY ELECTRICAL

B1244 Light Sensor Circuit Malfunction

Diagnostic trouble codes · Vehicles built from May 2007

DESCRIPTION

The automatic light control sensor detects ambient light, converts it into an electrical signal, and outputs it to the main body ECU. The main body ECU turns on or off the headlights and taillights according to the signal.
DTC No.
DTC Detecting Condition
Trouble Area
B1244
  1. Malfunction in automatic light control sensor
  2. Open or short in automatic light control sensor circuit
  1. Automatic light control sensor
  2. Harness or connector
  3. Main body ECU (Instrument panel junction block)

WIRING DIAGRAM

E124321E12

INSPECTION PROCEDURE


1. READ VALUE USING INTELLIGENT TESTER
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG).

  1. Turn the intelligent tester on.

  1. Select the following menu items: Body Electrical / Main Body / Data List.

  1. Read the display on the intelligent tester.

    Main Body: 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Illumination Rate
    Illumination rate information / 0 ms to 99.99 ms
    Value is output according to ambient light levels
    -

    OK:
    Normal condition listed above is displayed.



NG
Go to step 2
OK

REPLACE MAIN BODY ECU (INSTRUMENT PANEL JUNCTION BLOCK)

2. CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - AUTOMATIC LIGHT CONTROL SENSOR)

  1. E121476E13
    Disconnect the F1 automatic light control sensor connector.

  1. Disconnect the D6 main body ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    D6-18 (CLTE) - F1-3 (CLTE)
    Always
    Below 1 Ω
    D6-19 (CLTS) - F1-5 (CLTS)
    Always
    Below 1 Ω
    D6-20 (CLTB) - F1-6 (CLTB)
    Always
    Below 1 Ω
    D6-18 (CLTE) - Body ground
    Always
    10 kΩ or higher
    D6-19 (CLTS) - Body ground
    Always
    10 kΩ or higher
    D6-20 (CLTB) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3. INSPECT MAIN BODY ECU (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY )
  1. Reconnect the main body ECU connector.

  1. Measure the voltage and resistance according to the value(s) in the table below.E142675E04

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    D6-20 (CLTB) - D6-18 (CLTE)
    Ignition switch off
    Below 1 V
    Ignition switch on (IG)
    11 to 14 V

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    D6-18 (CLTE) - Body ground
    Always
    Below 1 Ω



NG
REPLACE MAIN BODY ECU (INSTRUMENT PANEL JUNCTION BLOCK)
OK


4. INSPECT AUTOMATIC LIGHT CONTROL SENSOR

  1. E142674E01
    Reconnect the automatic light control sensor connector.

  1. Connect an oscilloscope to the automatic light control sensor connector.

  1. B113714E01
    Check the waveform.

    OK:
    Tester Connection
    Tool Setting
    Condition
    Specified Condition
    F1-3 (CLTE) - F1-5 (CLTS)
    5 V/DIV., 5 ms./DIV.
    Ignition switch on (IG), light control switch in AUTO
    Correct waveform is as shown

HINT:
If the ambient light becomes brighter, width A becomes narrower.



NG
REPLACE AUTOMATIC LIGHT CONTROL SENSOR
OK

REPLACE MAIN BODY ECU (INSTRUMENT PANEL JUNCTION BLOCK)


← DIAGNOSTIC TROUBLE CODE CHART (from May 2007)IG Signal Circuit (May 2007 – Jul 2008) →