2007-2013 Highlander Kluger · Service Manual BODY

DISASSEMBLY

Removal / installation · Vehicles built May 2007 – Jul 2008

Versions by build date: May 2007 – Jul 2008 Aug 2008 – Jun 2010 from Jul 2010


1. DISCONNECT NEGATIVE BATTERY TERMINAL

CAUTION:
Wait for 90 seconds after disconnecting the terminal to prevent airbag deployment (Click here).

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).


2. REMOVE FRONT DOOR LOWER FRAME BRACKET GARNISH

  1. B172931
    Disengage the claw and clip, and remove the front door lower frame bracket garnish.


3. REMOVE FRONT DOOR INSIDE HANDLE BEZEL PLUG

  1. B172920E01
    Using a screwdriver with the tip wrapped with protective tape, disengage the 3 claws, and remove the front door inside handle bezel plug.


4. REMOVE FRONT ARMREST UPPER BASE PANEL

  1. B172922E01
    Using a screwdriver with the tip wrapped with protective tape, disengage the 7 claws and clip, and remove the front armrest upper base panel.

  1. Disconnect the connector.


5. REMOVE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY (for Driver Side)

  1. B172926
    Remove the 3 screws and the power window regulator master switch assembly.


6. REMOVE POWER WINDOW REGULATOR SWITCH ASSEMBLY (for Front Passenger Side)

  1. B172927
    Disengage the 2 claws and remove the power window regulator switch assembly.


7. REMOVE DOOR CONTROL SWITCH ASSEMBLY (for Front Passenger Side)

  1. B172928
    Disengage the 2 claws and remove the door control switch assembly.


8. REMOVE ASSIST GRIP COVER

  1. B174183E01
    Using a screwdriver with the tip wrapped with protective tape, disengage the 4 claws and remove the assist grip cover.


9. REMOVE COURTESY LIGHT ASSEMBLY

  1. B172929E01
    Using a screwdriver with the tip wrapped with protective tape, disengage the claw and remove the courtesy light assembly.

  1. Disconnect the connector.


10. REMOVE FRONT DOOR TRIM BOARD SUB-ASSEMBLY

  1. B172932
    Remove the 3 screws.

  1. B172933
    Using a clip remover, disengage the 9 clips.

  1. Disengage the 5 claws and separate the front door trim board sub-assembly from the front door inner glass weatherstrip.

  1. B172934
    Disengage the 2 clamps.

  1. Disconnect the front door lock remote control cable and front door inside locking cable.

  1. Disconnect the connector.


11. REMOVE FRONT DOOR INSIDE HANDLE SUB-ASSEMBLY

  1. B172936
    Remove the 2 screws.

  1. Disengage the 2 claws and remove the front door inside handle sub-assembly.


12. REMOVE FRONT DOOR WIRE (for Driver Side)

  1. B172937
    Disengage the 3 clamps and remove the front door wire.


13. REMOVE FRONT DOOR INNER GLASS WEATHERSTRIP

  1. B172938
    Remove the front door inner glass weatherstrip from the front door panel.


14. REMOVE FRONT NO. 1 SPEAKER ASSEMBLY

  1. E150556
    Disconnect the connector.

  1. Remove the 4 bolts and front No. 1 speaker assembly.

    NOTICE:
    Do not touch the cone part of the speaker.


15. REMOVE OUTER REAR VIEW MIRROR ASSEMBLY WITH COVER

  1. B173464E01
    Disconnect the connector and clamp.

  1. Disengage the clip.

  1. B173465
    Remove the 3 nuts.

  1. Disengage the claw and remove the outer rear view mirror assembly with cover.


16. REMOVE FRONT DOOR SERVICE HOLE COVER

  1. B172939
    Disconnect the each connector and 2 clamps, and remove the front door service hole cover.

    HINT:
    Remove the remaining butyl tape on the door side.


17. REMOVE FRONT DOOR GLASS SUB-ASSEMBLY

  1. B172940
    Remove the hole plug.

  1. Connect the negative battery terminal.

  1. Connect the power window regulator motor connector.

  1. Connect the power window regulator master switch assembly and move the front door glass sub-assembly so that the door glass bolts can be seen.

  1. Disconnect the negative battery terminal and power window regulator master switch assembly.

  1. Disconnect the power window regulator motor connector.

  1. B172941
    Remove the 2 bolts.

    NOTICE:
    After the bolts are removed, do not allow the door to fall.

  1. B172942E01
    Remove the front door glass sub-assembly as shown in the illustration.

    NOTICE:
    Do not damage the door glass.


18. REMOVE FRONT DOOR WINDOW REGULATOR SUB-ASSEMBLY

  1. B172943E01
    Loosen the temporary bolt.

    NOTICE:
    Do not remove the temporary bolt. If the temporary bolt is removed, the front door window regulator may fall and cause damage.

  1. Remove the 5 bolts.

  1. Remove the front door window regulator sub-assembly and the front power window regulator motor assembly as a unit.

  1. Remove the temporary bolt from the front door window regulator sub-assembly.


19. REMOVE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY

  1. B172944
    Using a "TORX" driver (T25), remove the 3 screws and the front power window regulator motor assembly.


20. REMOVE FRONT DOOR GLASS RUN

  1. B172946
    Remove the front door glass run.


21. REMOVE FRONT DOOR REAR LOWER FRAME SUB-ASSEMBLY

  1. B172948
    Remove the bolt and the front door rear lower frame sub-assembly as shown in the illustration.


22. REMOVE FRONT DOOR OUTSIDE HANDLE COVER (for Driver Side)

  1. B172949
    Remove the hole plug.

  1. Using a "TORX" socket wrench (T30), loosen the screw and remove the front door outside handle cover and the door lock key cylinder as a unit.

    HINT:
    The screw cannot be removed because it is integrated into the front door outside handle frame sub-assembly.

  1. B172950
    Using a screwdriver, disengage the 2 claws and remove the front door outside handle cover.


23. REMOVE FRONT DOOR OUTSIDE HANDLE COVER (for Front Passenger Side)

  1. B172952
    Remove the hole plug.

  1. Using a "TORX" socket wrench (T30), loosen the screw and remove the front door outside handle cover and the door lock key cylinder as a unit.

    HINT:
    The screw cannot be removed because it is integrated into the front door outside handle frame sub-assembly.


24. REMOVE FRONT DOOR OUTSIDE HANDLE ASSEMBLY (w/o Smart Entry and Start System)

  1. B172953
    Remove the front door outside handle assembly as shown in the illustration.


25. REMOVE FRONT DOOR OUTSIDE HANDLE ASSEMBLY (w/ Smart Entry and Start System)

  1. B174199
    Disconnect the connector.

  1. B172955
    Remove the front door outside handle assembly as shown in the illustration.


26. REMOVE FRONT DOOR FRONT OUTSIDE HANDLE PAD

  1. B172957
    Disengage the 3 claws and remove the front door front outside handle pad.


27. REMOVE FRONT DOOR REAR OUTSIDE HANDLE PAD

  1. B172958
    Disengage the 2 claws and remove the front door rear outside handle pad.


28. REMOVE FRONT DOOR LOCK ASSEMBLY

  1. B172959
    Using a "TORX" socket wrench (T30), remove the 3 screws.

  1. Slide the front door lock assembly downward, and remove the front door lock assembly and cables as a unit.

  1. Remove the door lock wiring harness seal from the front door lock assembly.


29. REMOVE FRONT DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY

  1. B172961
    Remove the front door lock remote control cable assembly.


30. REMOVE FRONT DOOR INSIDE LOCKING CABLE ASSEMBLY

  1. B172962
    Using a screwdriver, disengage the 3 claws.

    HINT:
    Tape the screwdriver tip before use.

  1. B172963
    Remove the front door inside locking cable assembly.


31. REMOVE FRONT DOOR OUTSIDE HANDLE FRAME SUB-ASSEMBLY (w/o Smart Entry and Start System)

  1. B172965
    Using a "TORX" socket wrench (T30), remove the screw.

  1. Disengage the 2 claws and remove the front door outside handle frame sub-assembly.


32. REMOVE FRONT DOOR OUTSIDE HANDLE FRAME SUB-ASSEMBLY (w/ Smart Entry and Start System)

  1. B174201
    Using a "TORX" socket wrench (T30), remove the screw.

  1. Disconnect the connector.

  1. Disengage the clamp.

  1. Disengage the 2 claws and remove the front door outside handle frame sub-assembly.


33. REMOVE FRONT DOOR LOCK OPEN ROD

  1. B172966E01
    Remove the front door lock open rod as shown in the illustration.


34. REMOVE DOOR ELECTRICAL KEY OSCILLATOR (w/ Smart Entry and Start System)

  1. B174202
    Remove the screw and door electrical key oscillator.


35. REMOVE FRONT DOOR CHECK ASSEMBLY

  1. B172968
    Remove the bolt, 2 nuts, and front door check assembly.


36. REMOVE FRONT DOOR WEATHERSTRIP

  1. B172969
    Using a clip remover, disengage the 17 clips and remove the front door weatherstrip.


37. REMOVE DOOR FRAME GARNISH

  1. B172947
    Disengage the clip and remove the door frame garnish.

    HINT:
    This clip needs to be replaced with a new one because the clip will break when removing the door frame garnish.


38. REMOVE FRONT DOOR NO. 2 STIFFENER CUSHION

  1. B172945
    Remove the 2 bolts.

  1. Remove the 2 guides and the front door No. 2 stiffener cushion.


39. REMOVE FRONT DOOR BELT MOULDING ASSEMBLY

  1. B172791E01
    Put protective tape around the front door belt moulding assembly.

  1. B172792
    Disengage the 6 claws and remove the front door belt moulding assembly.

    NOTICE:
    Be careful when removing the moulding as there are claws attached to the front and rear ends of the moulding.


40. REMOVE FRONT DOOR WEATHERSTRIP

  1. B172970
    Disengage the claw.

  1. Disengage the 8 clips and remove the front door weatherstrip.


41. REMOVE FRONT DOOR OUTSIDE MOULDING SUB-ASSEMBLY

  1. B172799
    Turn back the front door weatherstrip.

  1. Remove the nut.

  1. B172800E01
    Peel off the upper front door outside moulding pad and disengage the 11 clips, and then remove the front door outside moulding sub-assembly.

  1. Remove the gasket from the front door outside moulding sub-assembly.

  1. Remove the 3 No. 3 clips pad from the front door outside moulding sub-assembly.

  1. Remove the 8 No. 4 clips pad from the front door outside moulding sub-assembly.

  1. B172801E01
    Remove the upper front door outside moulding pad from the front door outside moulding sub-assembly.


42. REMOVE NO. 1 BLACK OUT TAPE
  1. Using a heat light, heat the No. 1 black out tape and vehicle body.

    Heating temperature:
    Item
    Temperature
    Vehicle Body
    40 to 60°C (104 to 140°F)

    NOTICE:
    Do not heat the vehicle body excessively.

  1. Pull back an end of the No. 1 black out tape and pull it parallel to the vehicle body to pull it off.


43. REMOVE INNER UPPER BLACK OUT FRONT DOOR TAPE
  1. Using a heat light, heat the inner upper black out front door tape and vehicle body.

    Heating temperature:
    Item
    Temperature
    Vehicle Body
    40 to 60°C (104 to 140°F)

    NOTICE:
    Do not heat the vehicle body excessively.

  1. Pull back an end of the inner upper black out front door tape and pull it parallel to the vehicle body to pull it off.


44. REMOVE INNER REAR BLACK OUT FRONT DOOR TAPE
  1. Using a heat light, heat the inner rear black out front door tape and vehicle body.

    Heating temperature:
    Item
    Temperature
    Vehicle Body
    40 to 60°C (104 to 140°F)

    NOTICE:
    Do not heat the vehicle body excessively.

  1. Pull back an end of the inner rear black out front door tape and pull it parallel to the vehicle body to pull it off.

← ON-VEHICLE INSPECTION (from May 2007)DISASSEMBLY (Aug 2008 – Jun 2010) →