2007-2013 Highlander Kluger · Service Manual BODY

DISASSEMBLY

Removal / installation · Vehicles built Aug 2008 – Jun 2010

Versions by build date: May 2007 – Jul 2008 Aug 2008 – Jun 2010 from Jul 2010


1. DISCONNECT NEGATIVE BATTERY TERMINAL

CAUTION:
Wait for 90 seconds after disconnecting the terminal to prevent airbag deployment (Click here).

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).


2. REMOVE REAR DOOR INSIDE HANDLE BEZEL PLUG

  1. B172920E01
    Using a screwdriver with the tip wrapped with protective tape, disengage the 3 claws and remove the rear door inside handle bezel plug.


3. REMOVE REAR DOOR ARMREST UPPER BASE PANEL

  1. B172987E01
    Using a screwdriver with the tip wrapped with protective tape, disengage the 6 claws and 2 clips, and remove the rear door armrest upper base panel.

  1. Disconnect the connector.


4. REMOVE REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY

  1. B173154
    Disengage the 2 claws and remove the rear power window regulator switch assembly.


5. REMOVE DOOR ASSIST GRIP COVER

  1. B174184E01
    Using a screwdriver with the tip wrapped with protective tape, disengage the 4 claws and remove the door assist grip cover.


6. REMOVE REAR DOOR TRIM BOARD SUB-ASSEMBLY

  1. B173155
    Remove the 3 screws.

  1. B173156
    Using a clip remover, disengage the 9 clips.

  1. Disengage the 5 claws and separate the rear door trim board sub-assembly from the rear door inner glass weatherstrip.

  1. B173157
    Disengage the 2 clamps.

  1. Disconnect the front door lock remote control cable and rear door inside locking cable.


7. REMOVE REAR DOOR INSIDE HANDLE SUB-ASSEMBLY

  1. B173159
    Remove the 2 screws.

  1. Disengage the 2 claws and disconnect the rear door inside handle sub-assembly.


8. REMOVE REAR SPEAKER ASSEMBLY

  1. E150558
    Disconnect the connector.

  1. Remove the 3 bolts and rear speaker assembly.

    NOTICE:
    Do not touch the cone part of the speaker.


9. REMOVE REAR DOOR INNER GLASS WEATHERSTRIP

  1. B173160
    Remove the rear door inner glass weatherstrip from the rear door panel.


10. REMOVE REAR DOOR SERVICE HOLE COVER

  1. B173161
    Disconnect the connector.

  1. Remove the rear door service hole cover.

    HINT:
    Remove the remaining tape on the door.


11. REMOVE REAR DOOR CHECK ASSEMBLY

  1. B173162
    Remove the bolt, 2 nuts, and the rear door check assembly.


12. REMOVE REAR DOOR WEATHERSTRIP

  1. B173163
    Using a clip remover, disengage the 19 clips and remove the rear door weatherstrip.


13. REMOVE REAR DOOR GLASS RUN

  1. B173165
    Remove the rear door glass run.


14. REMOVE REAR DOOR FRAME GARNISH

  1. B173166
    Disengage the clip and remove the rear door frame garnish.

    HINT:
    This clip needs to be replaced with a new one because the clip will break when removing the rear door frame garnish.


15. REMOVE REAR DOOR WINDOW DIVISION BAR SUB-ASSEMBLY

  1. B173164
    Remove the rear door vent seal.

  1. B173167
    Remove the 2 bolts, screw, and the rear door window division bar sub-assembly.


16. REMOVE REAR DOOR QUARTER WINDOW GLASS

  1. B173168
    Remove the rear door quarter window glass and the rear door quarter window weatherstrip as a unit as shown in the illustration.

  1. Remove the rear door quarter window glass from the rear door quarter window weatherstrip.


17. REMOVE REAR DOOR GLASS SUB-ASSEMBLY

  1. B173170
    Remove the rear door glass sub-assembly from the rear door window regulator sub-assembly as shown in the illustration.

    NOTICE:
    Do not damage the door glass.


18. REMOVE REAR DOOR WINDOW REGULATOR SUB-ASSEMBLY

  1. B173172E01
    Disconnect the connector.

  1. Loosen the temporary bolt.

    NOTICE:
    Do not remove the temporary bolt. If the temporary bolt is removed, the rear door window regulator may fall and cause damage.

  1. Remove the 3 bolts.

  1. Remove the rear door window regulator sub-assembly and the rear power window regulator motor assembly as a unit.

  1. Remove the temporary bolt from the rear door window regulator sub-assembly.


19. REMOVE REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY

  1. B173173E01
    Connect the positive (+) lead of the battery to terminal 2, and the negative (-) lead to terminal 1 of the rear power window regulator motor assembly to move the lift arm to the position shown in the illustration.

  1. B173175
    Using a "TORX" driver (T25), remove the 3 screws and the rear power window regulator motor assembly.


20. REMOVE REAR DOOR LOCK ASSEMBLY

  1. B173177
    Using a "TORX" socket wrench (T30), remove the 3 screws.

  1. Move the rear door lock assembly downward and pull the release plate out of the rear door outside handle frame.

  1. Remove the door lock wiring harness seal from the rear door lock assembly.


21. REMOVE REAR DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY

  1. B173178
    Using a screwdriver, disengage the claw.

    HINT:
    Tape the screwdriver tip before use.

  1. B173179
    Remove the rear door lock remote control cable assembly.


22. REMOVE REAR DOOR INSIDE LOCKING CABLE ASSEMBLY

  1. B173180
    Using a screwdriver, disengage the 3 claws.

    HINT:
    Tape the screwdriver tip before use.

  1. B173181
    Remove the rear door inside locking cable assembly.


23. REMOVE REAR DOOR OUTSIDE HANDLE COVER

  1. B173182
    Using a "TORX" socket wrench (T30), loosen the screw.

    HINT:
    The screw cannot be removed because it is integrated into the rear door outside handle frame sub-assembly.

  1. B173183
    Disengage the claw and remove the rear door outside handle cover.


24. REMOVE REAR DOOR OUTSIDE HANDLE ASSEMBLY

  1. B173184
    Pull and hold the release plate of the rear door outside handle frame sub-assembly as shown in the illustration.

    NOTICE:
    The rear door outside handle assembly may be damaged when removing the rear door outside handle assembly, unless the release plate of the rear door outside handle frame sub-assembly is pulled and held.

  1. B173185
    Remove the rear door outside handle assembly as shown in the illustration.


25. REMOVE REAR DOOR FRONT OUTSIDE HANDLE PAD

  1. B172957
    Disengage the 3 claws and remove the rear door front outside handle pad.


26. REMOVE REAR DOOR REAR OUTSIDE HANDLE PAD

  1. B172958
    Disengage the 2 claws and remove the rear door rear outside handle pad.


27. REMOVE REAR DOOR OUTSIDE HANDLE FRAME SUB-ASSEMBLY

  1. B173187
    Using a "TORX" socket wrench (T30), remove the screw.

  1. Disengage the 2 claws and remove the rear door outside handle frame sub-assembly.


28. REMOVE REAR DOOR BELT MOULDING ASSEMBLY

  1. B172793E01
    Put protective tape around the rear door belt moulding assembly.

  1. B172794
    Disengage the 6 claws and remove the rear door belt moulding assembly.

    NOTICE:
    Be careful when removing the moulding as there are claws attached to the front end of the moulding.


29. REMOVE REAR DOOR NO. 2 WEATHERSTRIP

  1. B173189
    Disengage the claw.

  1. Disengage the 11 clips and remove the rear door No. 2 weatherstrip.


30. REMOVE REAR DOOR OUTSIDE MOULDING SUB-ASSEMBLY

  1. B172802
    Turn back the rear door No. 2 weatherstrip.

  1. Remove the nut.

  1. B172803E01
    Peel off the upper rear door outside moulding pad and disengage the 8 clips, and then remove the rear door outside moulding sub-assembly.

  1. Remove the gasket from the rear door outside moulding sub-assembly.

  1. Remove the 2 No. 3 clips pad from the rear door outside moulding sub-assembly.

  1. Remove the 6 No. 4 clips pad from the rear door outside moulding sub-assembly.

  1. B172804E01
    Remove the upper rear door outside moulding pad from the rear door outside moulding sub-assembly.


31. REMOVE NO. 3 BLACK OUT TAPE
  1. Using a heat light, heat the No. 3 black out tape and vehicle body.

    Heating temperature:
    Item
    Temperature
    Vehicle Body
    40 to 60°C (104 to 140°F)

    NOTICE:
    Do not heat the vehicle body excessively.

  1. Pull back an end of the No. 3 black out tape and pull it parallel to the vehicle body to pull it off.


32. REMOVE NO. 2 BLACK OUT TAPE
  1. Using a heat light, heat the No. 2 black out tape and vehicle body.

    Heating temperature:
    Item
    Temperature
    Vehicle Body
    40 to 60°C (104 to 140°F)

    NOTICE:
    Do not heat the vehicle body excessively.

  1. Pull back an end of the No. 2 black out tape and pull it parallel to the vehicle body to pull it off.


33. REMOVE INNER UPPER BLACK OUT REAR DOOR TAPE
  1. Using a heat light, heat the inner upper black out rear door tape and vehicle body.

    Heating temperature:
    Item
    Temperature
    Vehicle Body
    40 to 60°C (104 to 140°F)

    NOTICE:
    Do not heat the vehicle body excessively.

  1. Pull back an end of the inner upper black out rear door tape and pull it parallel to the vehicle body to pull it off.


34. REMOVE INNER FRONT BLACK OUT REAR DOOR TAPE
  1. Using a heat light, heat the inner front black out rear door tape and vehicle body.

    Heating temperature:
    Item
    Temperature
    Vehicle Body
    40 to 60°C (104 to 140°F)

    NOTICE:
    Do not heat the vehicle body excessively.

  1. Pull back an end of the inner front black out rear door tape and pull it parallel to the vehicle body to pull it off.


35. REMOVE INNER REAR BLACK OUT REAR DOOR TAPE
  1. Using a heat light, heat the inner rear black out rear door tape and vehicle body.

    Heating temperature:
    Item
    Temperature
    Vehicle Body
    40 to 60°C (104 to 140°F)

    NOTICE:
    Do not heat the vehicle body excessively.

  1. Pull back an end of the inner rear black out rear door tape and pull it parallel to the vehicle body to pull it off.

← DISASSEMBLY (May 2007 – Jul 2008)DISASSEMBLY (from Jul 2010) →