DATA LIST / ACTIVE TEST
System information · Vehicles built from May 2007
| DATA LIST |
- HINT:
- Using the intelligent tester to read the DATA LIST allows values or status of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the DATA LIST information early in troubleshooting is one way to save diagnostic time.
- CAUTION:
- In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
Connect the intelligent tester to the DLC3.
Turn the ignition switch on (IG).
Turn the intelligent tester on.
Enter the following menus.
Select: Body / D-Door Motor / DATA LIST.
D-Door Motor: Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
D Door P/W Auto SW
Driver door power window auto switch signal/ON or OFF
ON: Driver door power window auto switch operates
OFF: Driver door power window auto switch does not operate
-
D Door P/W Up SW
Driver door power window manual up switch signal/ON or OFF
ON: Driver door power window manual up switch operates
OFF: Driver door power window manual up switch does not operate
-
D Door P/W Down SW
Driver door power window manual down switch signal/ON or OFF
ON: Driver door power window manual down switch operates
OFF: Driver door power window manual down switch does not operate
-
Glass Position (Close - 1/4)
Jam protection operation within range of fully closed to 1/4 open window glass position/OK or CAUTION
OK: Margin is sufficient during manual UP operation
CAUTION: May be displayed even when no resistance is applied in each position. In this case, there is a foreign object stuck in that position.
-
Glass Position (1/4 - 2/4)
Jam protection operation within range of 1/4 to 1/2 open window glass position/OK or CAUTION
OK: Margin is sufficient during manual UP operation
CAUTION: May be displayed even when no resistance is applied in each position. In this case, there is a foreign object stuck in that position.
-
Glass Position (2/4 - 3/4)
Jam protection operation within range of 1/2 to 3/4 open window glass position/OK or CAUTION
OK: Margin is sufficient during manual UP operation
CAUTION: May be displayed even when no resistance is applied in each position. In this case, there is a foreign object stuck in that position.
-
Glass Position (3/4 - Open)
Jam protection operation within range of 3/4 to fully open window glass position/OK or CAUTION
OK: Margin is sufficient during manual UP operation
CAUTION: May be displayed even when no resistance is applied in each position. In this case, there is a foreign object stuck in that position.
-
Select: Body / Main Body / DATA LIST.
Main Body: Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
Communication D Door Motor
Connection status between power window regulator motor assembly (driver door) and main body ECU (Instrument panel junction block)/OK/Stop
OK: Communication is normal
STOP: Communication is stopped
-
D Door Courtesy SW
Driver side door courtesy switch signal/ON or OFF
ON: Driver side door is open
OFF: Driver side door is closed
-
| ACTIVE TEST |
- HINT:
- Using the intelligent tester to perform ACTIVE TESTS allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. DATA LIST information can be displayed while performing ACTIVE TESTS.
Connect the intelligent tester to the DLC3.
Turn the ignition switch on (IG).
Turn the intelligent tester on.
Enter the following menus.
Select: Body / D-Door Motor / Active Test.
D-Door Motor: Tester Display
Test Part
Control Range
Diagnostic Note
Power Window
Power window
UP or OFF
-
Power Window
Power window
DOWN or OFF
-
Select: Body / Main Body / Active Test.
Main Body: Tester Display
Test Part
Control Range
Diagnostic Note
IG OFF P/W Control Permission Output
Power window
ON or OFF (After ignition switch is turned OFF)
-