2007-2013 Highlander Kluger · Service Manual BODY ELECTRICAL

SYSTEM DESCRIPTION

Troubleshooting · Vehicles built May 2007 – Jul 2008

Versions by build date: May 2007 – Jul 2008 from Aug 2008


OUTLINE OF THE COMBINATION METER ASSEMBLY
*: for 4WD
E146918E01
Meter gauge: 
Item
Detail
Speedometer
Indicates the vehicle speed based on a signal received from the skid control ECU. (CAN (CAN No. 1 Bus))
Tachometer
Indicates the engine speed based on a signal received from the ECM. (CAN (CAN No. 1 Bus))
Engine Coolant Temperature Receiver Gauge
Indicates the engine coolant temperature based on a signal received from the ECM. (CAN (CAN No. 1 Bus))
Fuel Receiver Gauge
Indicates the fuel level based on a fuel level signal received from the fuel sender gauge (Direct Line) and a fuel injection signal and an ST signal received from the ECM. (CAN (CAN No. 1 Bus))
Warning/Indicator: 
Item
Detail
Turn
Receives a turn signal from the turn signal flasher. (Direct Line)
Beam
Receives a beam indicator light signal from the main body ECU. (CAN (CAN No. 1 Bus))
Charge
Receives a charge indicator light signal from the generator. (Direct Line)
MIL (Check engine)
Receives a check engine warning light signal from the ECM. (Direct Line)
Door
Receives a door condition signal from the main body ECU. (CAN (CAN MS Bus))
Driver side seat belt
Receives a driver side seat belt signal from the center airbag sensor assembly. (CAN (CAN No. 1 Bus))
Front passenger side seat belt
Receives a passenger side seat belt signal from the center airbag sensor assembly and transmits a passenger side seat belt condition signal to the hazard warning switch. (Direct Line)
Tail
Receives a indicator light signal from the main body ECU. (CAN (CAN No. 1 Bus))
Front fog
Receives a front fog indicator light signal from the main body ECU. (CAN (CAN No. 1 Bus))
A/T shift
Receives an A/T shift condition signal from the park/neutral position switch and the ECM. (CAN (CAN No. 1 Bus))
A/T fluid temperature
Receives an A/T fluid temperature signal from the park/neutral position switch and the ECM. (CAN (CAN No. 1 Bus))
ECT snow
Receives an ECT snow signal from the park/neutral position switch and the ECM. (CAN (CAN No. 1 Bus))
Fuel
Receives a fuel signal from the fuel sender gauge. (Direct Line)
ABS
Receives an ABS signal from the skid control ECU. (CAN (CAN No. 1 Bus))
Slip
Receives a slip signal from the skid control ECU. (CAN (CAN No. 1 Bus))
Brake
Receives a brake signal from the brake fluid level warning switch (Direct Line) and the skid control ECU. (CAN (CAN No. 1 Bus))
Cruise
Receives a cruise signal from the ECM. (CAN (CAN No. 1 Bus))
SRS
Receives an SRS signal from the center airbag sensor assembly. (CAN (CAN No. 1 Bus))
Downhill assist control (*)
Receives a downhill assist control signal from the skid control ECU. (CAN (CAN No. 1 Bus))
VSC off (*)
Receives a VSC off signal from the skid control ECU. (CAN (CAN No. 1 Bus))
EPS
Receives an EPS signal from the power steering ECU. (CAN (CAN No. 1 Bus))
Washer
Receives a washer signal from the washer level warning switch. (Direct Line)
Master caution indicator light
Comes on when the warning display appears.

CLOCK ASSEMBLY (w/ Multi-information Display)
Item
Detail
Cruise information display
  1. Average fuel consumption
  2. Current fuel consumption
  3. Possible running distance
  4. Total cruising distance
  5. Total average fuel consumption
Five types of information (average fuel consumption, current fuel consumption, possible running distance, total cruising distance since reset, and total average fuel consumption since reset) can be displayed.
Warning display
  1. Door warning
  2. Each system warning
Interrupts the multi-information display immediately when a warning occurs.
Air conditioning display
Interrupts the multi-information display immediately when air conditioning is operated.
Rear view monitor display
Interrupts the multi-information display immediately when the A/T shift position is moved to R.
DTC (Diagnostic Trouble Code) display
Displays DTCs pertaining to the VSC function.

DISPLAY FLOW CHART

HINT:
Illustrations may differ from the actual screen displayed depending on the specifications of the vehicle and customized settings.

  1. Display flow chart:
    E152460E01

  2. Each warning mode flow chart:
    E152461E01

  3. Warning indication for each language:
    E152462E01
    E152463E01


LED INITIAL CHECK
  1. The illumination function of the warning, indicator, or reminder light listed below can be confirmed when the ignition switch on (IG).

    OK:
    Indicator/Warning Light
    Specified Condition
    Brake, ABS, Slip, EPS, VSC off (*), A/T fluid temperature, Downhill assist control (*)
    Indicator/Warning light comes on for about 3 seconds after turning the ignition switch on (IG).
    SRS
    Warning light comes on for about 6 seconds after turning the ignition switch on (IG).
    Charge, Oil pressure
    Indicator/Warning light comes on after turning the ignition switch on (IG).
    MIL (Check engine)
    Warning light comes on while turning the ignition switch on (IG) before engine start.

    *: for 4WD

← SYSTEM DIAGRAM (from Aug 2008)SYSTEM DESCRIPTION (from Aug 2008) →