2007-2013 Highlander Kluger · Service Manual ENGINE

REMOVAL

Removal / installation · Vehicles built May 2007 – Jul 2008

Versions by build date: May 2007 – Jul 2008 Aug 2008 – Jun 2010 Jul 2010 – Jul 2013 from Aug 2013


1. REMOVE ENGINE UNDER COVER ASSEMBLY

  1. A171849
    Remove the 2 bolts and engine under cover assembly RR.

  1. A171850
    Remove the 2 bolts, 2 screws, 5 clips and engine under cover assembly.


2. REMOVE NO. 1 ENGINE UNDER COVER

  1. A171855
    Remove the 6 bolts, 2 clips and No. 1 engine under cover.


3. DRAIN ENGINE COOLANT

  1. Loosen the radiator drain cock plug.

    A169414E01

    HINT:
    Collect the coolant in a container and dispose of it according to the regulations in your area.

  1. Remove the radiator cap sub-assembly from the radiator assembly.

    NOTICE:
    Do not remove the radiator cap sub-assembly while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.

  1. Loosen the 2 cylinder block drain cock plugs.


4. REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY LH

  1. E150144
    Remove the nut, and the front wiper arm and blade assembly LH.


5. REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY RH

  1. E150145
    Remove the nut, and the front wiper arm and blade assembly RH.


6. REMOVE COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY

  1. E150146
    Disengage the 2 claws and disconnect the front fender to cowl side seal LH.

  1. E150147
    Disengage the 2 claws and disconnect the front fender to cowl side seal RH.

  1. Remove the 2 clips.

    E150149

  1. Disengage the 20 claws and remove the cowl top ventilator louver sub-assembly.


7. REMOVE WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY

  1. E150150
    Disconnect the connector.

  1. Remove the 4 bolts, and the windshield wiper motor and link assembly.


8. REMOVE OUTER COWL TOP PANEL SUB-ASSEMBLY

  1. C165925
    Disengage the 4 clamps and separate the wiper wire harness from the outer cowl top panel sub-assembly.

  1. C165926
    Remove the 8 bolts, 6 nuts, and the outer cowl top panel sub-assembly.


9. REMOVE V-BANK COVER SUB-ASSEMBLY

  1. A162365
    Hold the front of the V-bank cover sub-assembly and raise it to disengage the 2 clips on the front of the V-bank cover sub-assembly. Continue rising the V-bank cover sub-assembly to disengage the clip on the rear of the V-bank cover sub-assembly and remove the V-bank cover sub-assembly.

    NOTICE:
    Attempting to disengage both front and rear clips at the same time may cause the V-bank cover sub-assembly to break.


10. REMOVE AIR CLEANER CAP SUB-ASSEMBLY

  1. A170887
    Disconnect the 3 vacuum hoses.

  1. A170447
    Loosen the No. 1 air cleaner hose clamp.

  1. Disconnect the hose clamps and No. 2 ventilation hose.

  1. Disconnect the mass air flow meter connector.

  1. A170451
    Release the 2 clips, and remove the 2 bolts.

  1. Remove the air cleaner cap sub-assembly and air cleaner filter element.


11. REMOVE THROTTLE BODY

  1. A135707
    Disconnect the throttle body connector and clamp.

  1. A135708
    Disconnect the 2 water by-pass hoses from the throttle body.

  1. A135709
    Remove the 4 bolts and throttle body.

  1. A133820E01
    Remove the throttle body gasket from the intake air surge tank assembly.

← ON-VEHICLE INSPECTION (from May 2007)REMOVAL (Aug 2008 – Jun 2010) →