2007-2013 Highlander Kluger · Service Manual ENGINE

INSTALLATION

Removal / installation · Vehicles built Jul 2010 – Jul 2013

Versions by build date: May 2007 – Jul 2008 Aug 2008 – Jun 2010 Jul 2010 – Jul 2013 from Aug 2013


1. INSTALL CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (for Bank 2)

  1. Exhaust side:

    1. A141324E02
      Apply a coat of engine oil to a new O-ring and install it onto the camshaft timing oil control valve assembly.

    2. A135695
      Install the camshaft timing oil control valve assembly with the bolt.

      Torque:
      10 N*m{ 102 kgf*cm , 7 ft.*lbf }

    3. Connect the camshaft timing oil control valve assembly connector. (RHD)

  1. Intake side:

    1. A141323E02
      Apply a coat of engine oil to a new O-ring and install it onto the camshaft timing oil control valve assembly.

    2. A171717
      Install the camshaft timing oil control valve assembly with the bolt.

      Torque:
      10 N*m{ 102 kgf*cm , 7 ft.*lbf }

    3. Connect the camshaft timing oil control valve assembly connector. (RHD)


2. INSTALL CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (for Bank 1)

  1. Exhaust side:

    1. A141323E02
      Apply a coat of engine oil to a new O-ring and install it onto the camshaft timing oil control valve assembly.

    2. A171715
      Install the camshaft timing oil control valve assembly with the bolt.

      Torque:
      10 N*m{ 102 kgf*cm , 7 ft.*lbf }

    3. Connect the camshaft timing oil control valve assembly connector. (RHD)

  1. Intake side:

    1. A141322E02
      Apply a coat of engine oil to a new O-ring and install it onto the camshaft timing oil control valve assembly.

    2. A171716
      Install the camshaft timing oil control valve assembly with the bolt.

      Torque:
      10 N*m{ 102 kgf*cm , 7 ft.*lbf }

    3. Connect the camshaft timing oil control valve assembly connector. (RHD)


3. INSTALL HARNESS PROTECTOR (for LHD)

  1. Connect the 2 studs [A].

    A171713E02

  1. Connect the 2 clamps [B].

  1. Connect the 19 connectors [C].

  1. Install the 5 bolts and nuts [D].

    Torque:
    8.3 N*m{ 84 kgf*cm , 73 in.*lbf }


4. INSTALL HARNESS CLAMP BRACKET (for RHD)

  1. Install the 2 bolts and harness clamp brackets.

    Torque:
    8.3 N*m{ 84 kgf*cm , 73 in.*lbf }


    A171714


5. TEMPORARILY INSTALL NO. 1 SURGE TANK STAY

NOTICE:
DO NOT apply oil to the bolts listed below:
Tightening Parts
No. 1 Surge Tank Stay and Intake Air Surge Tank Assembly
No. 1 Surge Tank Stay and Cylinder Head Cover RH

  1. A171949
    Temporarily install the intake air surge tank assembly with 3 new gaskets on the intake manifold.

    NOTICE:
    Do not allow the gaskets to slip out of place during installation.

  1. Temporarily install the No. 1 surge tank stay with the 2 bolts.


6. TEMPORARILY INSTALL THROTTLE BODY BRACKET

NOTICE:
DO NOT apply oil to the bolts listed below:
Tightening Parts
Throttle body bracket and Intake Air Surge Tank Assembly
Throttle body bracket and Cylinder Head Cover RH

  1. A172966
    Temporarily install the throttle body bracket with the 2 bolts.


7. INSTALL INTAKE AIR SURGE TANK ASSEMBLY

NOTICE:
DO NOT apply oil to the bolts listed below:
Tightening Parts
Intake Manifold and Intake Air Surge Tank Assembly

  1. A169366E03
    Install the surge tank with the 4 bolts and 2 nuts in the order shown in the illustration.

    Torque:
    Nut:
    16 N*m{ 163 kgf*cm , 12 ft.*lbf }
    Bolt:
    18 N*m{ 183 kgf*cm , 13 ft.*lbf }

    HINT:
    Use a 5 mm hexagon socket wrench to tighten the 4 bolts.

  1. A169364
    Connect the 2 water by-pass hoses to the throttle with motor body assembly.

  1. A169363
    Connect the connector.

  1. Install the clamp and connect the throttle with motor body assembly connector.

  1. A171946E03
    Connect the 4 hoses.

    HINT:
    1. H: vapor feed hose
    2. I: union to check valve hose
    3. J: No. 1 ventilation hose
    4. K: vacuum hose


8. FULLY TIGHTEN NO. 1 SURGE TANK STAY

NOTICE:
DO NOT apply oil to the bolts listed below:
Tightening Parts
No. 1 Surge Tank Stay and Intake Air Surge Tank Assembly
No. 1 Surge Tank Stay and Cylinder Head Cover RH

  1. A172967E02
    Fully tighten the 2 bolts in the order shown in the illustration.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }


9. FULLY TIGHTEN THROTTLE BODY BRACKET

NOTICE:
DO NOT apply oil to the bolts listed below:
Tightening Parts
Throttle body bracket and Intake Air Surge Tank Assembly
Throttle body bracket and Cylinder Head Cover RH

  1. A172966E02
    Fully tighten the 2 bolts in the order shown in the illustration.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }


10. CONNECT ENGINE ROOM MAIN WIRE

  1. A172968
    Connect the 5 harness clamps.


11. INSTALL AIR CLEANER CAP SUB-ASSEMBLY

  1. A171941E01
    Install the air cleaner filter element, align the groove on the air cleaner hose with the throttle body alignment tab and tighten the clamp as shown in the illustration.

    HINT:
    1. A = 30°
    2. B = 11 to 14 mm (0.433 in. to 0.551 in.)

  1. Install the air cleaner cap with the 2 bolts and clips.

    Torque:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }

  1. A170887
    Connect the 3 vacuum hoses.

  1. A171944
    Connect the mass air flow meter connector.

  1. Connect the No. 2 ventilation hose and fuel vapor feed hose assembly.


12. ADD ENGINE COOLANT
  1. Tighten the radiator drain cock plug by hand.

  1. Tighten the 2 cylinder block drain cock plugs.

    Torque:
    13 N*m{ 130 kgf*cm , 9 ft.*lbf } for cylinder block drain cock plugs

  1. Loosen the air drain cock plug from the water inlet housing.

  1. A169415E01
    Loosen the air drain plug at the top of the radiator 3 or 4 turns.

  1. Add TOYOTA Super Long Life Coolant (SLLC) to the radiator inlet opening until coolant overflows from the engine air drain cock hole. Then tighten the air drain cock plug to the water inlet housing.

    Torque:
    13 N*m{ 130 kgf*cm , 9 ft.*lbf } for air drain cock plug

  1. Continue to add TOYOTA Super Long Life Coolant (SLLC) to the radiator inlet opening until coolant overflows from the radiator air drain hole. Then close the air drain plug at the top of the radiator.

    Torque:
    1.5 N*m{ 15 kgf*cm , 13 in.*lbf } for air drain plug

    HINT:
    If the coolant level at the radiator inlet opening drops after squeezing the No. 1 and No. 2 radiator hoses, add coolant.

  1. Slowly fill the radiator with TOYOTA Super Long Life Coolant (SLLC).

    Standard capacity:
    Condition
    Specified Condition
    w/ Rear Heater
    11.7 liters (12.4 US qts, 10.3 Imp. qts)
    w/o Rear Heater
    9.5 liters (10.1 US qts, 8.4 Imp. qts)

    HINT:
    1. TOYOTA vehicles are filled with TOYOTA SLLC at the factory. In order to avoid damage to the engine cooling system and other technical problems, only use TOYOTA SLLC or similar high quality ethylene glycol based non-silicate, non-amine, non-nitrite, non-borate coolant with long-life hybrid organic acid technology (coolant with long-life hybrid organic acid technology is a combination of low phosphates and organic acids).
    2. Contact your TOYOTA dealer for further details.

    NOTICE:
    Never use water as a substitute for engine coolant.

  1. Slowly pour coolant into the radiator reservoir tank until it reaches the FULL line.

  1. Squeeze the No. 1 and No. 2 radiator hoses several times by hand, and then check the level of the coolant.
    If the coolant level is low, add coolant.

  1. Bleed air from the cooling system.

    1. Warm up the engine until the thermostat opens. While the thermostat is open, circulate the coolant for several minutes.

      HINT:
      The thermostat open timing can be confirmed by squeezing the inlet radiator hose by hand, and checking when the engine coolant starts to flow inside the hose.

    2. Maintain the engine speed at 2500 to 3000 rpm.

    3. Squeeze the inlet and outlet radiator hoses several times by hand to bleed air.

      CAUTION:
      When squeezing the radiator hoses:
      1. Wear protective gloves.
      2. Be careful as the radiator hoses are hot.
      3. Keep your hands away from the radiator fan.

      NOTICE:
      1. Make sure that the radiator reservoir still has some coolant in it.
      2. If the coolant temperature gauge indicates an excessive temperature, turn off the engine and let it cool.
      3. If there is not enough coolant, the engine may overheat or be seriously damaged.
      4. If the radiator reservoir does not have enough coolant, perform the following: 1) stop the engine, 2) wait until the coolant has cooled down, and 3) add coolant until the reservoir is filled to the FULL line.

  1. Stop the engine and wait until the engine coolant cools down.

  1. Add engine coolant to the FULL line on the radiator reservoir.


13. INSPECT FOR COOLANT LEAK

CAUTION:
Do not remove the radiator cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.

NOTICE:
Before performing each inspection, turn the A/C switch off.

  1. A169405
    Fill the radiator with coolant and attach a radiator cap tester.

  1. Warm up the engine.

  1. Using the radiator cap tester, increase the pressure inside the radiator to 118 kPa (1.2 kgf/cm2, 17 psi), and check that the pressure does not drop.
    If the pressure drops, check the hoses, radiator and water pump for leaks. If no external leaks are found, check the heater core, cylinder block and cylinder head.


14. INSTALL OUTER COWL TOP PANEL SUB-ASSEMBLY

  1. C165926E01
    Install the outer cowl top panel sub-assembly with the 8 bolts and 6 nuts.

    Torque:
    Nut A:
    85 N*m{ 866 kgf*cm , 63 ft.*lbf }
    Bolt B:
    8.8 N*m{ 90 kgf*cm , 78 in.*lbf }
    Nut C:
    8.8 N*m{ 90 kgf*cm , 78 in.*lbf }

  1. C165925
    Engage the 4 clamps.


15. INSTALL WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY

  1. E150150
    Install the windshield wiper motor and link assembly with the 4 bolts.

    Torque:
    7.0 N*m{ 71 kgf*cm , 62 in.*lbf }

  1. Connect the connector.


16. INSTALL COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY

  1. Engage the 20 claws.

    E150149

  1. Install the cowl top ventilator louver sub-assembly with the 2 clips.

  1. E150146
    Engage the 2 claws and connect the front fender to cowl side seal LH.

  1. E150147
    Engage the 2 claws and connect the front fender to cowl side seal RH.


17. INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY RH
  1. Operate the wiper and stop the windshield wiper motor at the automatic stop position.

  1. When reinstalling:

    1. E112237E01
      Clean the wiper arm serrations.

    2. Clean the wiper pivot serrations with a wire brush.

  1. E147125E01
    Install the front wiper arm and blade assembly RH with the nut to the position shown in the illustration.

    Torque:
    24 N*m{ 245 kgf*cm , 18 ft.*lbf }

    HINT:
    Hold the wiper arm by hand when tightening the nut.

    Area
    Measurement
    A
    25.6 mm (1.00 in.)


18. INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY LH
  1. Operate the wiper and stop the windshield wiper motor at the automatic stop position.

  1. When reinstalling:

    1. E112237E01
      Clean the wiper arm serrations.

    2. Clean the wiper pivot serrations with a wire brush.

  1. E152618E01
    Install the front wiper arm and blade assembly LH with the nut to the position shown in the illustration.

    Torque:
    24 N*m{ 245 kgf*cm , 18 ft.*lbf }

    HINT:
    Hold the wiper arm by hand when tightening the nut.

    Area
    Measurement
    A
    31.9 mm (1.26 in.)

  1. Operate the front wipers while spraying washer fluid onto the windshield glass. Make sure that the front wipers function properly and the wipers do not come into contact with the vehicle body.


19. INSTALL V-BANK COVER SUB-ASSEMBLY

  1. A162365
    Fit the 3 retainers and install the V-bank cover.


20. INSTALL NO. 1 ENGINE UNDER COVER

  1. A237657
    Install the No. 1 engine under cover with the 6 bolts and 2 clips.


21. INSTALL ENGINE UNDER COVER ASSEMBLY

  1. A171850
    Install the engine under cover assembly with the 2 bolts, 2 screws and 5 clips.

  1. A171849
    Install the engine under cover assembly RR with the 2 bolts.

← INSTALLATION (Aug 2008 – Jun 2010)INSTALLATION (from Aug 2013) →