2007-2013 Highlander Kluger · Service Manual BODY

REMOVAL

Removal / installation · Vehicles built from Jul 2010

Versions by build date: May 2007 – Jul 2008 Aug 2008 – Jun 2010 from Jul 2010


1. REMOVE INNER REAR VIEW MIRROR ASSEMBLY (w/o EC Mirror)

  1. for Type A:

    1. B175040
      Disengage the 2 claws and disconnect the inner mirror base cover.

    2. B175041E01
      Pull the lock lever in the direction indicated by the arrow in the illustration, and slide the inner rear view mirror assembly upward to remove it.
      Text in Illustration 
      *1
      Lock Lever

  1. for Type B:

    1. B279254
      Using a T20 "TORX" socket wrench, remove the screw.

    2. B280442
      Slide the inner rear view mirror assembly in the direction indicated by the arrow shown in the illustration to remove it.


2. REMOVE INNER REAR VIEW MIRROR STAY HOLDER COVER (w/ EC Mirror)

  1. B175048E01
    Disengage the 2 claws and slide the inner rear view mirror stay holder cover as shown in the illustration.

  1. B175049
    Disengage the 2 claws and remove the inner rear view mirror stay holder cover.


3. REMOVE INNER REAR VIEW MIRROR ASSEMBLY (w/ EC Mirror)

  1. B175042
    Disconnect the connector.

  1. Using a "TORX" socket wrench (T20), remove the screw and the inner rear view mirror.


4. REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY LH

  1. E150144
    Remove the nut, and the front wiper arm and blade assembly LH.


5. REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY RH

  1. E150145
    Remove the nut, and the front wiper arm and blade assembly RH.


6. REMOVE FRONT FENDER TO COWL SIDE SEAL LH

  1. B173472
    Disengage the 2 claws.

  1. B173473E01
    Disengage the 2 double-sided tapes.

  1. Disengage the claw and remove the front fender to cowl side seal LH as shown in the illustration.


7. REMOVE FRONT FENDER TO COWL SIDE SEAL RH

HINT:
Use the same procedure for the RH side and the LH side.


8. REMOVE COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY

  1. Remove the 2 clips.

    E150149

  1. Disengage the 20 claws and remove the cowl top ventilator louver sub-assembly.


9. REMOVE FRONT PILLAR GARNISH LH

  1. B260103E01
    Pull the upper part of the garnish toward the inside of the cabin and disengage the garnish from the base of the 2 clips.

    HINT:
    Make the front pillar garnish LH hang down from the front pillar garnish clip.

  1. B260104E01
    Turn the end of the front pillar garnish clip 90° with needle-nosed pliers and remove it from the front pillar garnish LH.

    NOTICE:
    1. Front pillar garnish clips are reusable if they are not removed from the vehicle and have no damage.
    2. Replace the front pillar garnish clips with new ones if they are removed from the vehicle.

  1. Disengage the 3 guides at the front end of the front pillar garnish LH and remove it.

  1. B173225E01
    Protect the curtain shield airbag assembly.

    1. Cover the airbag with a 700 mm (27.56 in.) x 120 mm (4.72 in.) cloth or piece of nylon and fix the ends of the cover with tape as shown in the illustration.

      NOTICE:
      Cover the curtain shield airbag with a protective cover as soon as the front pillar garnish is removed.


10. REMOVE FRONT PILLAR GARNISH RH

  1. B260157E01
    Pull the upper part of the garnish toward the inside of the cabin and disengage the garnish from the base of the 2 clips.

    HINT:
    Make the front pillar garnish RH hang down from the front pillar garnish clip.

  1. B260158E01
    Turn the end of the front pillar garnish clip 90° with needle-nosed pliers and remove it from the front pillar garnish RH.

    NOTICE:
    1. Front pillar garnish clips are reusable if they are not removed from the vehicle and have no damage.
    2. Replace the front pillar garnish clips with new ones if they are removed from the vehicle.

  1. Disengage the 3 guides at the front end of the front pillar garnish RH and remove it.

  1. B173684E01
    Protect the curtain shield airbag assembly.

    1. Cover the airbag with a 700 mm (27.56 in.) x 120 mm (4.72 in.) cloth or piece of nylon and fix the ends of the cover with tape as shown in the illustration.

      NOTICE:
      Cover the curtain shield airbag with a protective cover as soon as the front pillar garnish is removed.


11. REMOVE ROOF CONSOLE BOX ASSEMBLY

  1. B173250
    Using a moulding remover, disengage the 2 clips, 3 guides and fastener.

  1. Disconnect the connector and remove the roof console box assembly.


12. REMOVE VISOR BRACKET COVER (for LH Side)

  1. B132069
    Using a moulding remover, disengage the 4 claws and remove the visor bracket cover.


13. REMOVE VISOR ASSEMBLY LH

  1. B173261
    Remove the 2 screws and remove the visor assembly LH.


14. REMOVE VISOR BRACKET COVER (for RH Side)

HINT:
Use the same procedure for the RH side and the LH side.


15. REMOVE VISOR ASSEMBLY RH

HINT:
Use the same procedure for the RH side and the LH side.


16. REMOVE FRONT ASSIST GRIP SUB-ASSEMBLY (w/o Sliding Roof)

  1. B153056E01
    Using a clip remover, disengage the 4 claws.

    NOTICE:
    Do not forcibly pry the assist grip covers to prevent them from being deformed.

    HINT:
    1. Gently pry on the assist grip covers as shown in the illustration to remove them.
    2. Tape the clip remover tip before use.

  1. B153057
    Pull off the 2 assist grip covers by hand.

  1. Disengage the 2 clips and remove the front assist grip sub-assembly.

  1. Remove the 2 clips from the vehicle body.

    HINT:
    Use the same procedure for the RH side and the LH side.


17. REMOVE ASSIST GRIP ASSEMBLY (w/ Sliding Roof)

  1. B173257E01
    Using a screwdriver, disengage the 6 claws and remove the 2 assist grip covers.

    NOTICE:
    Do not forcibly pry the assist grip covers to prevent them from being deformed.

    HINT:
    Tape the screwdriver tip before use.

  1. B173258
    Disengage the 4 clips and remove the assist grip sub-assembly.

  1. Remove the 4 clips from the vehicle body.

    HINT:
    Use the same procedure for the RH side and the LH side.


18. REMOVE VISOR HOLDER

  1. B151362E01
    Turn the visor holder approximately 45° and pull it out as shown in the illustration.

  1. Disengage the 2 claws and remove the visor holder.

    HINT:
    Use the same procedure for the RH side and the LH side.


19. REMOVE ROOF HEADLINING ASSEMBLY
It is not necessary to completely remove the roof headlining assembly. Slightly lower the front section of the roof headlining assembly so that the windshield glass can be removed.

20. REMOVE WINDSHIELD GLASS

  1. B173463
    Disconnect the connector and clamp. (w/ Deicer)

  1. Disconnect the windshield glass stoppers.

    B173423E01

    NOTICE:
    1. There are No. 1 and No. 2 stoppers on the windshield glass sub-assembly as shown in the illustration. Be careful not to damage the windshield glass when cutting off the adhesive.
    2. To prevent the windshield glass sub-assembly from dropping when performing this operation, be sure to hold the windshield glass sub-assembly using suction cups.

    HINT:
    Depending on the vehicle, a 1-piece or 2-piece type stopper is used.

  1. B173424E01
    Apply protective tape to the installation position of the windshield glass sub-assembly on the vehicle body.

    NOTICE:
    Apply protective tape to the installation surface to prevent it from being scratched.

  1. Pass a piano wire between the vehicle body and windshield glass sub-assembly from the interior.

    B173425E01

  1. Tie both wire ends to wooden blocks or similar objects.

  1. Cut the adhesive by pulling the piano wire around the windshield glass sub-assembly.

    NOTICE:
    1. When separating the windshield glass sub-assembly from the vehicle, be careful not to damage the vehicle's paint or interior/exterior ornaments.
    2. To prevent the instrument panel from being scratched when removing the windshield glass sub-assembly, place a plastic sheet between the piano wire and instrument panel.
    3. Leave as much adhesive on the vehicle body as possible when removing the windshield glass sub-assembly.

  1. B173426E01
    Place matchmarks on the windshield glass sub-assembly and vehicle body on the locations indicated in the illustration.

    HINT:
    Matchmarks are not needed if the windshield glass sub-assembly is not going to be reused.

  1. Using suction cups, remove the windshield glass sub-assembly.

    NOTICE:
    Be careful not to drop the windshield glass sub-assembly.


21. REMOVE WINDOW GLASS ADHESIVE DAM
  1. Using a scraper, remove the windshield glass adhesive dam.

    NOTICE:
    1. Be careful not to damage the windshield glass.
    2. Be sure to replace the adhesive dam with a new one.


22. REMOVE NO. 2 WINDSHIELD GLASS STOPPER
  1. Using a scraper, remove the No. 2 window glass stoppers.

    NOTICE:
    1. Be careful not to damage the windshield glass.
    2. Be sure to replace the No. 2 windshield glass stoppers with new ones.


23. REMOVE NO. 1 WINDSHIELD GLASS STOPPER (for 2-piece Type)

  1. B173427
    Remove the 2 No. 1 windshield glass stoppers.

    NOTICE:
    Be sure to replace the No. 1 windshield glass stoppers with new ones.


24. CLEAN WINDSHIELD GLASS

  1. B106080
    Using a scraper, remove the damaged stoppers, dams and adhesive sticking to the glass.

  1. Clean the outer edges of the glass with a non-residue solvent.

    NOTICE:
    Do not touch the glass surface after cleaning it.
    Even if using new glass, clean it with a non-residue solvent.


25. CLEAN VEHICLE BODY

  1. B149737E02
    Clean and shape the contact surfaces of the vehicle body.

    1. On the contact surfaces of the vehicle body, use a knife to cut away excess adhesive as shown in the illustration.

      HINT:
      Leave as much adhesive on the vehicle body as possible.

      NOTICE:
      Be careful not to damage the vehicle body.

  1. Clean the contact surfaces of the vehicle body with cleaner.

    HINT:
    Even if all the adhesive has been removed, clean the vehicle body.

← REMOVAL (Aug 2008 – Jun 2010)INSTALLATION (May 2007 – Jul 2008) →