2007-2013 Highlander Kluger · Service Manual ENGINE

INSTALLATION

Removal / installation · Vehicles built from Jul 2010

Versions by build date: May 2007 – Jul 2008 Aug 2008 – Jun 2010 from Jul 2010


1. INSTALL FUEL TANK CUSHION SET

  1. A173206E01
    Install the 2 fuel tank cushion sets and 2 No. 5 fuel tank cushions.


2. INSTALL FUEL TANK SIDE PLATE

  1. A173205E01
    Install the fuel tank side plate and fuel tank bracket with the bolt and nut.

    Torque:
    30 N*m{ 306 kgf*cm , 22 ft.*lbf }

    HINT:
    While keeping the bolt from rotating, tighten the nut.


3. INSTALL TANK SUCTION TUBE SUPPORT

  1. A173207E01
    Install a new tank suction tube support as shown in the illustration.

    HINT:
    Align the protrusions of the tank suction tube support with the notches of the fuel tank assembly.


4. INSTALL FUEL TANK TO FILLER PIPE HOSE

  1. A173203
    Install the fuel tank to filler pipe hose with the hose clamp.


5. INSTALL FUEL PUMP TUBE SUB-ASSEMBLY

  1. A173202E01
    Engage the 2 claws to install the fuel pump tube sub-assembly.


6. INSTALL NO. 1 FUEL TANK CUSHION

  1. A173208E01
    Apply new butyl tape to the No. 1 fuel tank cushion as shown in the illustration.

    Length:
    Dimension
    Length
    A
    55 mm (2.17 in.)
    B
    20 mm (0.79 in.)
    C
    60 mm (2.36 in.)
    D
    20 mm (0.79 in.)
    E
    80 mm (3.15 in.)
    F
    20 mm (0.79 in.)
    G
    53.4 mm (2.10 in.)
    H
    49.2 mm (1.94 in.)
    I
    18.9 mm (0.74 in.)
    J
    43.3 mm (1.70 in.)

  1. Install the No. 1 fuel tank cushion.


7. INSTALL REAR FUEL TANK SIDE PLATE

  1. A173200
    Install the rear fuel tank side plate.


8. INSTALL FUEL TANK ASSEMBLY
  1. Set the fuel tank assembly onto a transmission jack.

  1. Using the transmission jack, install the fuel tank assembly.

  1. Tighten the 2 nuts.

    A173199

    Torque:
    20 N*m{ 200 kgf*cm , 14 ft.*lbf }

  1. Install the fuel tank band sub-assembly LH and RH with the 4 bolts.

    Torque:
    45 N*m{ 459 kgf*cm , 33 ft.*lbf }

  1. A175986E02
    Align the matchmarks and install the fuel tank to filler pipe hose to the filler pipe.

  1. Install the hose clamp within the range shown in the illustration.

    HINT:
    1. A = 45°
    2. B = 120°

  1. A175987E02
    Connect the No. 3 fuel tank breather tube.

  1. Install the hose clamp within the range shown in the illustration.

    HINT:
    1. A = 120°
    2. B = 2 to 7 mm (0.079 to 0.276 in.)

  1. A175780E01
    Connect the fuel tank vent hose.

  1. Install the clip within the range shown in the illustration.

    HINT:
    A= 120°

  1. A171925E03
    Connect the fuel pump tube sub-assembly.

    1. Push in the quick connector to the fuel pipe and push in the retainer to lock the claws.

      NOTICE:
      1. Check if there is any damage or foreign matter on the connecting parts.
      2. After connecting, check if the quick connector and the pipe are securely connected by pulling on them.


9. INSTALL NO. 1 FUEL TANK PROTECTOR SUB-ASSEMBLY

  1. A173194E01
    Install the No. 1 fuel tank protector sub-assembly with the 7 nuts.

    Torque:
    5.5 N*m{ 56 kgf*cm , 49 in.*lbf }

  1. Install 3 new clips (A).


10. TEMPORARILY INSTALL REAR SUSPENSION MEMBER (for 4WD)

  1. C166233E01
    Support the rear suspension member with a jack using a wooden block.

    HINT:
    1. Use a properly sized wooden block to keep the jack and suspension member level.
    2. Support the rear suspension member until retightening of the suspension member is complete.

  1. C166255
    Raise the rear suspension member with a jack.

  1. Temporarily install the rear suspension member, the 2 rear upper suspension member stoppers and rear lower suspension member stopper retainers with the 4 nuts and the 2 bolts.

  1. C166224E02
    Fully tighten the 2 nuts.

    Torque:
    115 N*m{ 1170 kgf*cm , 85 ft.*lbf }


11. FULLY TIGHTEN REAR SUSPENSION MEMBER (for 4WD)

  1. C167779E01
    Using SST and a socket wrench (19 mm), fully tighten the nut (LH side).

    Torque:
    without SST:
    181 N*m{ 1850 kgf*cm , 133 ft.*lbf }
    with SST:
    134 N*m{ 1366 kgf*cm , 98 ft.*lbf }

    SST
    09961-00950  

    NOTICE:
    1. Use a torque wrench with a fulcrum length of 425 mm (16.73 in.).
    2. This torque value is effective when SST is parallel to the torque wrench.

  1. C166256E01
    Using SST and a socket wrench (19 mm), fully tighten the nut (RH side).

    Torque:
    without SST:
    181 N*m{ 1850 kgf*cm , 133 ft.*lbf }
    with SST:
    134 N*m{ 1366 kgf*cm , 98 ft.*lbf }

    SST
    09961-00950  

    NOTICE:
    1. Use a torque wrench with a fulcrum length of 425 mm (16.73 in.).
    2. This torque value is effective when SST is parallel to the torque wrench.


12. INSTALL REAR DRIVE SHAFT SNAP RING LH (for 4WD)
  1. Install a new rear drive shaft snap ring.


13. INSTALL REAR DRIVE SHAFT ASSEMBLY LH (for 4WD)

  1. C166347
    Align the shaft splines and install the rear drive shaft assembly with a brass bar and hammer.

    NOTICE:
    1. Set the snap ring with the opening facing downward.
    2. Be careful not to damage the oil seal, boot, or dust cover.
    3. Install the drive shaft assembly while keeping it level.


14. INSTALL REAR DRIVE SHAFT SNAP RING RH (for 4WD)

HINT:
Perform the same procedure as the LH side.


15. INSTALL REAR DRIVE SHAFT ASSEMBLY RH (for 4WD)

HINT:
Perform the same procedure as the LH side.


16. INSTALL REAR DIFFERENTIAL DRAIN PLUG (for 4WD)

  1. C166707
    Using a hexagon wrench (10 mm), install the drain plug with a new gasket.

    Torque:
    49 N*m{ 500 kgf*cm , 36 ft.*lbf }


17. ADD DIFFERENTIAL OIL (for 4WD)
  1. Fill the rear differential carrier assembly with hypoid gear oil.


18. INSPECT DIFFERENTIAL OIL (for 4WD)
  1. Stop the vehicle on a level place.

  1. Remove the differential filler plug and gasket.

  1. C165855E01
    Check that the oil surface is within 5 mm (0.20 in.) of the lowest position of the inner surface of the differential filler plug opening.

    NOTICE:
    1. Excessively large or small amounts of oil may cause trouble.
    2. After replacing oil, drive the vehicle and check the oil level.

    HINT:
    If necessary, fill the rear differential carrier with hypoid gear oil.

    Oil grade:
    Hypoid gear oil API GL-5
    Recommended oil viscosity:
    Above -18°C (0°F) : SAE 90
    Below -18°C (0°F) : SAE 80W or 80W-90
    Capacity:
    0.9 +/- 0.05 liters (0.95 +/- 0.05 US qts, 0.79 +/- 0.04 lmp. qts)

  1. Check for oil leakage when the oil level is low.

  1. Install the differential filler plug and a new gasket.

    Torque:
    49 N*m{ 500 kgf*cm , 36 ft.*lbf }


19. INSTALL REAR DIFFERENTIAL FILLER PLUG (for 4WD)

  1. C166706
    Using a hexagon wrench (10 mm), install the filler plug with a new gasket.

    Torque:
    49 N*m{ 500 kgf*cm , 36 ft.*lbf }


20. TEMPORARILY INSTALL REAR NO. 1 SUSPENSION ARM ASSEMBLY RH (for 4WD)

C166223E01
  1. Temporarily install the rear No. 1 suspension arm assembly RH to the rear suspension member sub-assembly with the bolt and the nut.

    NOTICE:
    1. Ensure that the identification mark faces the rear side of the vehicle.
    2. Since a stopper nut is used, temporarily tighten the bolt.


21. TEMPORARILY INSTALL REAR NO. 2 SUSPENSION ARM ASSEMBLY LH (for 4WD)

C166222E02
  1. Temporarily install the rear No. 2 suspension arm assembly LH to the rear suspension member sub-assembly with the rear suspension toe adjust cam sub-assembly, the No. 2 camber adjust cam and the nut.

    NOTICE:
    Ensure that the identification mark faces the rear side of the vehicle.

    HINT:
    When temporarily tightening the nut, keep the rear suspension toe adjust cam sub-assembly from rotating.


22. TEMPORARILY INSTALL REAR NO. 2 SUSPENSION ARM ASSEMBLY RH (for 4WD)

HINT:
Perform the same procedure as the LH side.


23. INSTALL REAR AXLE CARRIER SUB-ASSEMBLY LH (for 4WD)

  1. C166002
    Temporarily install the the rear axle carrier sub-assembly with the 2 bolts and the 2 nuts.

    NOTICE:
    1. Be careful not to damage the outboard joint boot.
    2. Be careful not to damage the speed sensor rotor.
    3. Prevent foreign matter from adhering to the speed sensor rotor.

  1. C166001
    Install the rear axle carrier sub-assembly with the 2 bolts and the 2 nuts.

    Torque:
    290 N*m{ 2956 kgf*cm , 213 ft.*lbf }

    NOTICE:
    1. Be careful not to damage the outboard joint boot.
    2. Be careful not to damage the speed sensor rotor.
    3. Prevent foreign matter from adhering to the speed sensor rotor.
    4. Do not rotate the drive shaft with the rear axle hub and bearing assembly removed.

    HINT:
    Insert the bolts from the rear side.


24. INSTALL REAR AXLE CARRIER SUB-ASSEMBLY RH (for 4WD)

HINT:
Perform the same procedure as the LH side.


25. TEMPORARILY INSTALL REAR STRUT ROD ASSEMBLY LH (for 4WD)

  1. C165999E01
    Check that the identification mark of the rear strut rod assembly is positioned on the inner side of the vehicle.

  1. Temporarily install the rear strut rod assembly with the 2 bolts and the 2 nuts.

    NOTICE:
    Since stopper nuts are used, temporarily tighten the bolts.


26. TEMPORARILY INSTALL REAR STRUT ROD ASSEMBLY RH (for 4WD)

HINT:
Perform the same procedure as the LH side.


27. INSTALL REAR AXLE HUB AND BEARING ASSEMBLY LH (for 4WD)

  1. C166348E01
    Align the matchmarks on the drive shaft and rear axle hub.

    NOTICE:
    Do not rotate the drive shaft.

  1. C165997
    Install the parking brake assembly and the rear axle hub and bearing assembly with the 4 bolts.

    Torque:
    75 N*m{ 764 kgf*cm , 55 ft.*lbf }

    NOTICE:
    Do not twist the No. 3 parking brake cable assembly when installing it.


28. INSTALL REAR AXLE HUB AND BEARING ASSEMBLY RH (for 4WD)

HINT:
Perform the same procedure as the LH side.


29. INSTALL REAR DISC (for 4WD LH Side)

  1. C166438E01
    Align matchmarks and install the rear disc.

    NOTICE:
    When replacing the rear disc with a new one, select the installation position where the rear disc has minimal runout.


30. INSTALL REAR DISC (for 4WD RH Side)

HINT:
Perform the same procedure as the LH side.


31. INSTALL REAR DISC BRAKE CALIPER ASSEMBLY LH (for 4WD)

  1. C165996
    Install the rear disc brake caliper assembly with the 2 bolts.

    Torque:
    78 N*m{ 795 kgf*cm , 57 ft.*lbf }


32. INSTALL REAR DISC BRAKE CALIPER ASSEMBLY RH (for 4WD)

HINT:
Perform the same procedure as the LH side.


33. TEMPORARILY INSTALL REAR AXLE SHAFT NUT LH (for 4WD)

  1. C167784
    Clean the threaded parts on the rear drive shaft assembly and rear axle shaft nut using a non-residue solvent.

    NOTICE:
    1. Be sure to perform this work for a new rear drive shaft assembly.
    2. Keep the threaded parts free of oil and foreign objects.

  1. While applying the brakes, temporarily install a new rear axle shaft nut.

    Torque:
    294 N*m{ 2996 kgf*cm , 216 ft.*lbf }

    NOTICE:
    Stake the nut after inspecting for looseness and runout in the following steps.


34. TEMPORARILY INSTALL REAR AXLE SHAFT NUT RH (for 4WD)

HINT:
Perform the same procedure as the LH side.


35. INSTALL REAR SPEED SENSOR LH (for 4WD)

  1. C165809
    Install the rear speed sensor to the rear axle carrier sub-assembly with the bolt .

    Torque:
    8.5 N*m{ 87 kgf*cm , 75 in.*lbf }

    NOTICE:
    1. Keep the rear speed sensor tip and sensor installation hole free from foreign matter.
    2. To prevent interference with the bearing rotor, do not rotate the rear speed sensor body when inserting the rear speed sensor body or after inserting the rear speed sensor body.
    3. Do not twist the rear speed sensor wire when installing.


36. INSTALL REAR SPEED SENSOR RH (for 4WD)

HINT:
Perform the same procedure as the LH side.


37. STABILIZE SUSPENSION (for 4WD)

  1. C166003E01
    Jack up the rear axle carrier sub-assembly, placing a wooden block underneath to avoid damage. Apply load to the suspension so that the rear drive shaft assembly is positioned horizontally.

    CAUTION:
    Do not jack up the rear axle carrier sub-assembly too high as the vehicle may fall.

    NOTICE:
    Do not bend the brake dust cover.

    HINT:
    1. If the rear drive shaft assembly cannot be positioned horizontally as shown in the illustration even when the rear axle carrier sub-assembly is jacked up, apply additional load to the vehicle such as by having a person sit in the rear seat.
    2. Use the same procedure for the RH side and LH side.


38. FULLY TIGHTEN REAR NO. 1 SUSPENSION ARM ASSEMBLY LH (for 4WD)

  1. C166007
    Fully tighten the rear No. 1 suspension arm assembly with the bolt and nut.

    Torque:
    112 N*m{ 1141 kgf*cm , 82 ft.*lbf }

    NOTICE:
    1. Since a stopper nut is used, fully tighten the bolt.
    2. The final torque must be applied under standard vehicle height conditions.


39. FULLY TIGHTEN REAR NO. 1 SUSPENSION ARM ASSEMBLY RH (for 4WD)

C166219E01
  1. Fully tighten the 2 bolts.

    Torque:
    Bolt (A):
    80 N*m{ 815 kgf*cm , 59 ft.*lbf }
    Bolt (B):
    112 N*m{ 1141 kgf*cm , 82 ft.*lbf }

    NOTICE:
    1. Since a stopper nut is used, temporarily tighten the bolt.
    2. The final torque must be applied under standard vehicle height conditions.


40. FULLY TIGHTEN REAR NO. 2 SUSPENSION ARM ASSEMBLY LH (for 4WD)

C166217E01
  1. Align the matchmarks on the adjust cams and rear suspension member sub-assembly.

  1. Fully tighten the nut.

    Torque:
    100 N*m{ 1019 kgf*cm , 74 ft.*lbf }

    NOTICE:
    The final torque must be applied under standard vehicle height conditions.

    HINT:
    When fully tightening the nut, keep the rear suspension toe adjust cam sub-assembly from rotating.

  1. Fully tighten the bolt.

    Torque:
    112 N*m{ 1141 kgf*cm , 82 ft.*lbf }

    NOTICE:
    1. Since a stopper nut is used, fully tighten the bolt.
    2. The final torque must be applied under standard vehicle height conditions.


41. FULLY TIGHTEN REAR NO. 2 SUSPENSION ARM ASSEMBLY RH (for 4WD)

HINT:
Perform the same procedure as the LH side.


42. FULLY TIGHTEN REAR STRUT ROD ASSEMBLY LH (for 4WD)

  1. C166006
    Fully tighten the bolt.

    Torque:
    80 N*m{ 815 kgf*cm , 59 ft.*lbf }

    NOTICE:
    1. Since a stopper nut is used, fully tighten the bolt.
    2. The final torque must be applied under standard vehicle height conditions.

  1. C166005
    Fully tighten the bolt.

    Torque:
    80 N*m{ 815 kgf*cm , 59 ft.*lbf }

    NOTICE:
    1. Since a stopper nut is used, fully tighten the bolt.
    2. The final torque must be applied under standard vehicle height conditions.


43. FULLY TIGHTEN REAR STRUT ROD ASSEMBLY RH (for 4WD)

HINT:
Perform the same procedure as the LH side.


44. INSTALL NO. 3 PARKING BRAKE CABLE ASSEMBLY (for 4WD)

  1. C165998
    Install the No. 3 parking brake cable assembly with the bolt and the nut.

    Torque:
    Bolt:
    39 N*m{ 397 kgf*cm , 29 ft.*lbf }
    Nut:
    6.0 N*m{ 61 kgf*cm , 53 in.*lbf }

    NOTICE:
    Do not twist the No. 3 parking brake cable assembly when installing it.


45. INSTALL NO. 2 PARKING BRAKE CABLE ASSEMBLY (for 4WD)

HINT:
Perform the same procedure as the No. 3 parking brake cable assembly.


46. SEPARATE REAR DISC BRAKE CALIPER ASSEMBLY LH (for 4WD)

  1. C165996
    Remove the 2 bolts and separate the rear disc brake caliper assembly.

    NOTICE:
    Use wire or an equivalent tool to keep the brake caliper from hanging down by the flexible hose.


47. SEPARATE REAR DISC BRAKE CALIPER ASSEMBLY RH (for 4WD)

HINT:
Perform the same procedure as the LH side.


48. REMOVE REAR DISC (for 4WD LH Side)

  1. C166438E01
    Put matchmarks on the rear disc and the axle hub.

  1. D028126
    Release the parking brake and remove the rear disc.

    HINT:
    If the disc cannot be removed easily, turn and press firmly the shoe adjuster until the wheel comes free.


49. REMOVE REAR DISC (for 4WD RH Side)

50. INSPECT REAR AXLE HUB BEARING LOOSENESS (for 4WD LH Side)

  1. C165994
    Using a dial indicator, check for looseness near the center of the rear axle hub and bearing assembly.

    Maximum looseness:
    0 mm (0 in.)

    NOTICE:
    Ensure that the dial indicator is set perpendicular to the measurement surface.

    HINT:
    If the looseness exceeds the maximum, replace the rear axle hub and bearing assembly.


51. INSPECT REAR AXLE HUB BEARING LOOSENESS (for 4WD RH Side)

HINT:
Perform the same procedure as the LH side.


52. INSPECT REAR AXLE HUB RUNOUT (for 4WD LH Side)

  1. C165995
    Using a dial indicator, check for runout on the surface of the rear axle hub and bearing assembly outside the rear axle hub bolt.

    Maximum runout:
    0.08 mm (0.0031 in.)

    NOTICE:
    Ensure that the dial indicator is set perpendicular to the measurement surface.

    HINT:
    If the runout exceeds the maximum, replace the rear axle hub and bearing assembly.


53. INSPECT REAR AXLE HUB RUNOUT (for 4WD RH Side)

HINT:
Perform the same procedure as the LH side.


54. INSTALL REAR DISC (for 4WD LH Side)

  1. C166438E01
    Align matchmarks and install the rear disc.

    NOTICE:
    When replacing the rear disc with a new one, select the installation position where the rear disc has minimal runout.


55. INSTALL REAR DISC (for 4WD RH Side)

HINT:
Perform the same procedure as the LH side.


56. INSTALL REAR DISC BRAKE CALIPER ASSEMBLY LH (for 4WD)

  1. C165996
    Install the rear disc brake caliper assembly with the 2 bolts.

    Torque:
    78 N*m{ 795 kgf*cm , 57 ft.*lbf }


57. INSTALL REAR DISC BRAKE CALIPER ASSEMBLY RH (for 4WD)

HINT:
Perform the same procedure as the LH side.


58. INSTALL REAR AXLE SHAFT NUT LH (for 4WD)

  1. C165541
    Using a chisel and a hammer, stake the rear axle shaft nut.


59. INSTALL REAR AXLE SHAFT NUT RH (for 4WD)

HINT:
Perform the same procedure as the LH side.


60. INSTALL REAR WHEELS (for 4WD)

Torque:
103 N*m{ 1050 kgf*cm , 76 ft.*lbf }


61. INSTALL NO. 4 EXHAUST PIPE SUPPORT BRACKET

  1. A173193
    Install the No. 4 exhaust pipe support bracket with the 2 bolts.

    Torque:
    22 N*m{ 224 kgf*cm , 16 ft.*lbf }


62. INSTALL CENTER EXHAUST PIPE ASSEMBLY

  1. A160224
    Using vernier calipers, measure the free length of the compression spring.
    Minimum
    41.5 mm (1.63 in.)

    HINT:
    If the length is less than the minimum, replace the compression spring.

  1. A138040E01
    Using a plastic-faced hammer and wooden block, tap in a new gasket until its surface is flush with the front No. 3 exhaust pipe sub-assembly.

    NOTICE:
    1. Tap in the gasket in the correct direction.
    2. Do not reuse the removed gasket.
    3. Do not push in the gasket while installing the center exhaust pipe assembly.

  1. Connect the 3 exhaust pipe supports, and install the center exhaust pipe assembly.

  1. A170125
    Install the 2 compression springs and 2 bolts.

    Torque:
    48 N*m{ 489 kgf*cm , 35 ft.*lbf }


63. INSTALL TAIL EXHAUST PIPE ASSEMBLY

  1. A160224
    Using vernier calipers, measure the free length of the compression spring.
    Minimum
    40.5 mm (1.59 in.)

    HINT:
    If the length is less than the minimum, replace the compression spring.

  1. A138040E01
    Using a plastic-faced hammer and wooden block, tap in a new gasket until its surface is flush with the center exhaust pipe assembly.

    NOTICE:
    1. Tap in the gasket in the correct direction.
    2. Do not reuse the removed gasket.
    3. Do not push in the gasket while installing the tail exhaust pipe assembly.

  1. Connect the exhaust pipe support, and install the tail exhaust pipe assembly.

  1. A170139
    Install the 2 compression springs and 2 bolts.

    Torque:
    48 N*m{ 489 kgf*cm , 35 ft.*lbf }


64. TEMPORARILY TIGHTEN PROPELLER WITH CENTER BEARING SHAFT ASSEMBLY (for 4WD)

  1. C166040E01
    Align the matchmarks on the propeller shaft flange and differential companion flange, and connect the shaft with the 4 bolts, 4 washers and 4 nuts.

  1. C166042E01
    Remove SST from the transaxle.

  1. Insert the yoke into the transaxle.

  1. C166041
    Install the 4 adjusting shims and propeller shaft with center bearing, and temporarily tighten the 4 bolts.

  1. C166040E01
    Tighten the 4 bolts.

    Torque:
    74 N*m{ 750 kgf*cm , 54 ft.*lbf }


65. FULLY TIGHTEN PROPELLER WITH CENTER BEARING SHAFT ASSEMBLY (for 4WD)

  1. C167196
    Remove the piece of cloth from the joint.

  1. Using a hexagon wrench (6 mm), tighten the 6 bolts.

    Torque:
    26 N*m{ 265 kgf*cm , 19 ft.*lbf }

  1. C166068E01
    With the vehicle unloaded, adjust the dimension between the rear side of the cover and shaft as shown in the illustration.

    (A):
    58.0 +/- 0.5 mm (2.283 +/- 0.02 in.)

  1. Under the same condition as above, adjust the front and rear dimensions between the edge surface of the center support bearing and the edge surface of the cushion respectively as shown, and then tighten the bolts.

    C166069E01

    Torque:
    37 N*m{ 375 kgf*cm , 27 ft.*lbf }

    (B):
    12.5 +/- 1.0 mm (0.492 +/- 0.039 in.)

  1. Check that the center line of the bracket is at the right angle in the shaft axial direction.

  1. If any vibration or noise occurs, perform joint angle check as follows and replace the adjusting shim with a proper one.

    1. Turn the propeller shaft several times by hand to stabilize the center support bearings.

    2. Using a jack, raise and lower the differential to stabilize the differential mounting cushion.

    3. Remove the transfer dynamic damper.

    4. Using SST, measure the transfer installation angle (A) and front propeller shaft installation angle (B).

      SST
      09370-50010  

      No. 1 joint angle:
      (A) - (B) = -1.3° to -3.3°

    5. Using SST, measure the rear propeller shaft installation angle (C) and rear differential shaft installation angle (D).

      SST
      09370-50010  

      No. 2 joint angle:
      (C) - (D) = 1.8° to 3.5°


      C166070E01

      HINT:
      If the measured angle is not within the specification, adjust it with the center support bearing adjusting shim.

      Center support bearing adjusting shim thickness:
      Thickness mm (in.)
      Thickness mm (in.)
      3.2 (0.126)
      11.0 (0.433)
      4.5 (0.177)
      13.5 (0.531)
      6.5 (0.256)
      15.5 (0.610)
      9.0 (0.354)
      17.5 (0.689)

    6. Install the transfer dynamic damper.

      Torque:
      26 N*m{ 265 kgf*cm , 19 ft.*lbf }


66. INSTALL FRONT CENTER FLOOR COVER

  1. C168089
    Engage the 4 clips to install the center front floor cover.

  1. C168088
    Install the 4 bolts, 2 screws, and the nut.


67. INSTALL FUEL SUCTION TUBE ASSEMBLY WITH PUMP AND GAUGE
(Click here)

68. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).


69. INSPECT SRS WARNING LIGHT
  1. Inspect the SRS warning light (Click here).


70. INSPECT EXHAUST GAS LEAK
If exhaust gas is leaking, repair the leak. Replace damaged or worn parts as necessary.

71. INSPECT AND ADJUST TRANSFER OIL (for 4WD)

  1. C083746E03
    Remove the No. 1 transfer case plug and gasket.

  1. Check the oil level is within 0 to 5 mm (0 to 0.20 in.) below the lowest end of the hole for the No. 1 transfer case plug.

    NOTICE:
    1. When changing oil, recheck the oil level after driving.
    2. Excessively large or small quantity of oil may cause some trouble.

  1. When the oil level is too low, check for oil leakage.

  1. Tighten the No. 1 transfer case plug with a new gasket.

    Torque:
    49 N*m{ 500 kgf*cm , 36 ft.*lbf }


72. INSPECT REAR WHEEL ALIGNMENT (for 4WD)

HINT:
Click here


73. CHECK ABS SPEED SENSOR SIGNAL (for 4WD)

HINT:
Click here

← INSTALLATION (Aug 2008 – Jun 2010)COMPONENTS (May 2007 – Jun 2010) →