2007-2013 Highlander Kluger · Service Manual RESTRAINTS

Front Passenger Side Seat Belt Warning Light Malfunction

Circuit diagnosis · Vehicles built Aug 2008 – Jun 2010

Versions by build date: May 2007 – Jul 2008 Aug 2008 – Jun 2010 from Jul 2010

DESCRIPTION

When the passenger seat belt is not fastened with the ignition switch on (IG) and the passenger seat occupied, the passenger seat belt warning light display blinks. The occupant detection sensor detects if the passenger seat is occupied and sends signals to the combination meter assembly. After receiving the signals from the occupant detection sensor and inner belt, the combination meter assembly sends signals to the navigation receiver assembly*1 or hazard warning switch*2 to request the passenger seat belt warning light to blink or go off.

HINT:
  1. *1: w/ Navigation System
  2. *2: w/o Navigation System


WIRING DIAGRAM

B164953E03

INSPECTION PROCEDURE


1. PERFORM ACTIVE TEST USING INTELLIGENT TESTER
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG).

  1. Read the DATA LIST according to the displays on the tester screen.

    Combination Meter 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Front Passenger Side Seat Belt
    Front passenger side seat belt warning light
    Front passenger side seat belt warning light is OFF / ON
    Confirm that the vehicle is stopped with engine idling



NG
Go to step 3
OK


2. CHECK HARNESS AND CONNECTOR

  1. B178458E01
    Disconnect the E1 connector from the combination meter.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E1-11 (P/SB) - Body ground
    Passenger seat occupied and buckle switch is on
    Below 100 Ω



NG
Go to step 6
OK

REPLACE COMBINATION METER (Click here)

3. CHECK HARNESS AND CONNECTOR (BATTERY - NAVIGATION RECEIVER OR HAZARD WARNING LIGHT)

  1. B154243E08
    Disconnect E13 connector from the navigation receiver.*1

  1. Disconnect E13 connector from the hazard warning switch.*2

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    E13-1 (B) - Body ground
    Ignition switch on (IG)
    11 to 14 V

    HINT:
    1. *1: w/ Navigation System
    2. *2: w/o Navigation System



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR, OR REPLACE FUSE
OK


4. CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER OR HAZARD WARNING LIGHT - BODY GROUND)

  1. B154243E07
    Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E13-5 (E) - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5. CHECK HARNESS AND CONNECTOR

  1. B178244E03
    Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E1-31 (PBLT) - E13-3 (PBEW)
    Always
    Below 1 Ω
    E1-31 (PBLT) or E13-3 (PBEW) - Body ground
    Always
    10 kΩ or higher

  1. Proceed to the next step based on the inspection result.

    Result:
    Result
    Proceed to
    OK (w/Navigation system)
    A
    OK (w/o Navigation system)
    B
    NG
    C



A
REPLACE NAVIGATION RECEIVER (Click here)

B
REPLACE HAZARD WARNING SWITCH (Click here)
C

REPAIR OR REPLACE HARNESS OR CONNECTOR

6. CHECK HARNESS AND CONNECTOR (COMBINATION METER - FRONT SEAT INNER BELT)

  1. B178462E02
    Disconnect N17 connector from the front seat inner belt RH.*1

  1. Disconnect O35 connector from the front seat inner belt LH.*2

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E1-11 (P/SB) - N17-1*1
    E1-11 (P/SB) - O35-1*2
    Always
    Below 1 Ω
    E1-11 (P/SB) or N17-1 - Body ground*1
    E1-11 (P/SB) or O35-1 - Body ground*2
    Always
    10 kΩ or higher

    HINT:
    1. *1: LHD
    2. *2: RHD



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (COMBINATION METER - FRONT SEAT INNER BELT)
OK


7. CHECK HARNESS AND CONNECTOR (FRONT SEAT INNER BELT - BODY GROUND)

  1. B178463E02
    Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    N17-4 - Body ground*1
    O35-4 - Body ground*2
    Always
    Below 1 Ω

    HINT:
    1. *1: LHD
    2. *2: RHD



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (FRONT SEAT INNER BELT - BODY GROUND)
OK


8. INSPECT OCCUPANT DETECTION SENSOR

  1. B156681E03
    Disconnect A connector from the occupant detection sensor.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    A-1 - A-3
    Passenger seat is occupied
    Below 100 Ω
    A-1 - A-3
    Passenger seat is not occupied
    1 MΩ or higher



NG
REPLACE OCCUPANT DETECTION SENSOR
OK

REPLACE FRONT SEAT INNER BELT (PASSENGER SIDE) (Click here)


← Front Passenger Side Seat Belt Warning Light Malfunction (May 2007 – Jul 2008)Front Passenger Side Seat Belt Warning Light Malfunction (from Jul 2010) →