DIAGNOSIS DISPLAY DETAILED DESCRIPTION
Troubleshooting · Vehicles built Aug 2008 – Jun 2010
Versions by build date: May 2007 – Jul 2008 Aug 2008 – Jun 2010
- HINT:
- This section contains a detailed description of displays in diagnostic mode.
- Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be shown exactly the same as on the actual vehicle screen.
- This section contains a detailed description of displays in diagnostic mode.
| SYSTEM CHECK |
System Check Mode Screen


Device Names and Hardware Address/*1
- HINT:
- Registered device names are displayed.
- If a device name is unknown to the system, its physical address is shown instead.
- Registered device names are displayed.
Address No.
Name
Address No.
Name
110
EMV
120
AVX
128
1DIN TV
140
AVN
144
G-BOOK
178
NAVI
17C
MONET
190
AUDIO H/U
1AC
CAMERA-C
1B0
Rr-TV
1C0
Rr-CONT
19D
BT-HF
1C4
PANEL
1C6
G/W
1C8
FM-M-LCD
1D8
CONT-SW
1EC
Body
118
EMVN
1F1
XM
1F2
SIRIUS
230
TV-TUNER
240
CD-CH2
250
DVD-CH
280
CAMERA
360
CD-CH1
3A0
MD-CH
17D
TEL
440
DSP-AMP
530
ETC
1F6
RSE
1A0
DVD-P
1D6
CLOCK
238
DTV
480
AMP
Check Result/*2
- HINT:
- Result codes for all devices are displayed.
Result
Meaning
Action
OK
The device does not respond with a DTC (excluding communication DTCs from the AVC-LAN).
-
EXCH
The device responds with a "replace"-type DTC.
Look up the DTC in "Unit Check Mode" and replace the device.
CHEK
The device responds with a "check"-type DTC.
Look up the DTC in "Unit Check Mode".
NCON
The device was previously present, but does not respond in diagnostic mode.
- Check power supply wire harness of the device.
- Check the AVC-LAN of the device.
Old
The device responds with an "old"-type DTC.
Look up the DTC in "Unit Check Mode".
NRES
The device responds in diagnostic mode, but gives no DTC information.
- Check power supply wire harness of the device.
- Check the AVC-LAN of the device.
- Check power supply wire harness of the device.
Code Clear/*3
- Present DTCs are cleared.
- Press the "Code CLR" switch for 3 seconds.
- Present DTCs are cleared.
Memory Clear/*4
- Present and past DTCs and registered connected device names are cleared.
- Press the "Memory CLR" switch for 3 seconds.
- Present and past DTCs and registered connected device names are cleared.
Diagnosis MENU Screen


- HINT:
- Each item is grayed out or not displayed based on the device settings.
Unit Check Mode Screen


Screen Description: Display
Contents
Device name/*1
Target device
Segment/*2
Target device logical address
DTC/*3
DTC (Diagnostic Trouble Code)
Timestamp/*4
The time and date of past DTCs are displayed. (The year is displayed in 2-digit format.)
Present code/*5
DTCs output in the service check are displayed.
Past code/*6
Diagnostic memory results and recorded DTCs are displayed.
Diagnosis clear switch/*7
Pushing this switch for 3 seconds clears the diagnostic memory data of the target device. (Both response to diagnostic system check result and the displayed data are cleared.)
LAN Monitor (Original) Screen


Check Result/*1
- HINT:
- Check results of all the devices are displayed.
Result
Meaning
Action
No Err (OK)
There are no communication DTCs.
-
CHEK
The device responds with a "check"-type DTC.
Look up the DTC in "Unit Check Mode".
NCON
The device was previously present, but does not respond in diagnostic mode.
- Check power supply wire harness of the device.
- Check the AVC-LAN of the device.
Old
The device responds with an "old"-type DTC.
Look up the DTC in "Unit Check Mode".
NRES
The device responds in diagnostic mode, but gives no DTC information.
- Check power supply wire harness of the device.
- Check the AVC-LAN of the device.
- Check power supply wire harness of the device.
LAN Monitor (Individual) Screen


Screen Description: Display
Contents
Device name/*1
Target device
Segment/*2
Target logical address
DTC/*3
DTC (Diagnostic Trouble Code)
Sub-code (device address)/*4
Physical address stored with DTC (If there is no address, nothing is displayed.)
Connection check No./*5
Connection check number stored with DTC
DTC occurrence/*6
Number of times the same DTC has been recorded
Diagnosis clear switch/*7
Pushing this switch for 3 seconds clears the diagnostic memory data of the target device. (Both response to diagnostic system check result and the displayed data are cleared.)
| DISPLAY CHECK |
Vehicle Signal Check Mode Screen


Screen Description: Display
Contents
Battery
Battery voltage is displayed.
PKB
Parking brake ON/OFF state is displayed.
REV
Reverse signal ON/OFF state is displayed.
IG
IG switch ON/OFF state is displayed.
TAIL
TAIL signal (Light control switch) ON/OFF state is displayed.
SPEED
Vehicle speed is displayed in km/h.
- HINT:
- Only items sending vehicle signals will be displayed.
- This screen is updated once per second when input signals to the vehicle are changed.
- Only items sending vehicle signals will be displayed.
| NAVIGATION CHECK |
Navigation Check Screen


- HINT:
- Each item is grayed out or not displayed based on the device settings.
GPS Information Screen


Satellite information/*1
Information from a maximum of 12 satellites is displayed on the screen. This information includes the target GPS satellite number, elevation angle, direction, and signal level.Receiving condition/*2
(DENSO model): Display
Contents
T
The system is receiving a GPS signal, but is not using it for location.
P
The system is using the GPS signal for location.
-
The system cannot receive a GPS signal.
(AISIN AW model): Display
Contents
01H
The system cannot receive a GPS signal.
02H
The system is tracing a satellite.
03H
The system is receiving a GPS signal, but is not using it for location.
04H
The system is using the GPS signal for location.
Measurement information/*3: Display
Contents
2D
2-dimensional location method is being used.
3D
3-dimensional location method is being used.
NG
Location data cannot be used.
Error
Reception error has occurred.
-
Any other state.
Position information/*4 Display
Contents
Position
Latitude and longitude information on the current position is displayed.
Date information/*5: Display
Contents
Date
The date/time information obtained from GPS signal is displayed in Greenwich mean time (GMT). The last 4 digits are displayed.
Vehicle Sensors Screen


Vehicle signal: Display
Contents
REV/*1
REV signal ON/OFF state is displayed.
SPD/*2
SPD signal condition is displayed.
Sensor signal: Display
Contents
Gyro sensor/*3
Gyro sensor output condition is displayed (when the vehicle runs straight or is stationary, the voltage is approximately 2.5 V).
- HINT:
- Signals are updated once per second only when vehicle sensor signals are changed.
Microphone & Voice Recognition Check Screen


Screen Description: Display
Contents
Microphone input level meter/*1
Monitors the microphone input level every 100 ms and displays the results in 8 different levels.
Recording switch/*2
Starts recording.
Stop switch/*3
Stops recording.
Play switch/*4
Plays the recorded voice.
Recording indicator/*5
Comes on while recording.
- HINT:
- The microphone input function is on at all times when this screen is displayed.
- While recording or playing, the switches other than the stop switch cannot be pushed.
- When no voice is recorded, the play switch cannot be pushed.
- Recording will stop after 5 seconds or by pushing the stop switch.
- The microphone input function is on at all times when this screen is displayed.
DVD Player Information Screen


Screen Description: Display
Contents
Trouble code/*1
Each code corresponding to the malfunctions is displayed. For details, refer to "Trouble Code Description".
Occurrence time/*2
- The date (year, month, day) and time (hour, minute, second) when the trouble code was detected are displayed as a time stamp. (Greenwich mean time)
- The time data to be displayed are received from the GPS receiver.
Trouble code clear switch/*3
All code data being displayed are cleared by pushing this switch for 3 seconds.
Returning switch/*4
The previous page is displayed. If the current displayed page is the first page, this switch cannot be operated.
Proceeding switch/*5
The next page is displayed. If the current displayed page is the last page, this switch cannot be operated.
Trouble Code Description: Code
Malfunction
Countermeasure
01
Cannot be recognized
Replace navigation receiver assembly.
03
Cannot be read
Follow the inspection procedure for DTC 58-42 (Click here).
- HINT:
- This is a DVD player check function in the navigation receiver assembly (built-in navigation ECU).
- The date (year, month, day) and time (hour, minute, second) when the trouble code was detected are displayed as a time stamp. (Greenwich mean time)