2007-2013 Highlander Kluger · Service Manual TRANSMISSION

P0717 Turbine Speed Sensor Circuit No Signal

Diagnostic trouble codes · Vehicles built from Jul 2010

Versions by build date: May 2007 – Jul 2008 Aug 2008 – Jun 2010 from Jul 2010

DESCRIPTION

This sensor detects the rotation speed of the input turbine. By comparing the input turbine speed signal (NT) with the counter gear speed sensor signal (NC), the ECM detects the shift timing of the gears and appropriately controls the engine torque and hydraulic pressure according to various conditions. Thus, providing smooth gear shift.
DTC No.
DTC Detection Condition
Trouble Area
P0717
ECM detects conditions (a), (b) and (c) continuously for 5 sec. or more: (1-trip detection logic)
(a) Vehicle speed: 50 km/h (31 mph) or more
(b) Park/neutral position switch (NSW (STAR) and R) is OFF
(c) Speed sensor (NT): less than 300 rpm
  1. Open or short in transmission revolution sensor NT (speed sensor NT) circuit
  2. Transmission revolution sensor NT (speed sensor NT)
  3. ECM
  4. Automatic transaxle assembly
Reference (Using an oscilloscope):
Check the waveform between terminals NT+ and NT- of the ECM connector.
C053419E13
Standard: Refer to the illustration. 
Terminal
NT+ - NT-
Tool setting
5 V/DIV, 0.5 ms/DIV
Vehicle condition
Vehicle speed 20 km/h (12 mph)

MONITOR DESCRIPTION

The NT terminal of the ECM detects a revolution signal from the speed sensor (NT) (input RPM). The ECM calculates a gearshift comparing the speed sensor (NT) with the speed sensor (NC).
While the vehicle is operating in 2nd, 3rd, 4th or 5th gear in the shift position of D, if the input shaft revolution is less than 300 rpm *1although the output shaft revolution is more than 1000 rpm *2, the ECM detects the trouble, illuminates the MIL and stores the DTC.
*1: Pulse is not output or is irregularly output.
*2: The vehicle speed is 50 km/h (31 mph) or more.

WIRING DIAGRAM

C228070E03

INSPECTION PROCEDURE


1. INSPECT SPEED SENSOR INSTALLATION

  1. BR03795E36
    Check the speed sensor installation.

    OK:
    The installation bolt is tightened properly and there is no clearance between the sensor and transaxle case.



NG
REPLACE SPEED SENSOR (NT) (Click here)
OK


2. INSPECT SPEED SENSOR (NT)

  1. C110343E68
    Disconnect the speed sensor connector from the transaxle.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    20°C (68°F)
    560 to 680 Ω



NG
REPLACE SPEED SENSOR (NT) (Click here)
OK


3. CHECK HARNESS AND CONNECTOR (SPEED SENSOR - ECM)

  1. C227852E04
    Connect the speed sensor connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    B48-9 (NT+) - B48-10 (NT-)
    20°C (68°F)
    560 to 680 Ω

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance (Check for short):
    Tester Connection
    Condition
    Specified Condition
    B48-9 (NT+) - Body ground
    Always
    10 kΩ or higher
    B48-10 (NT-) - Body ground



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM (for 2GR-FE) (Click here)


← P0717 Turbine Speed Sensor Circuit No Signal (Aug 2008 – Jun 2010)P0724 Brake Switch "B" Circuit High (May 2007 – Jul 2008) →