2007-2013 Highlander Kluger · Service Manual TRANSMISSION

P0746 Pressure Control Solenoid "A" Performance (Shift Solenoid Valve SL1)

Diagnostic trouble codes · Vehicles built May 2007 – Jul 2008

Versions by build date: May 2007 – Jul 2008 Aug 2008 – Jun 2010 from Jul 2010

SYSTEM DESCRIPTION

The ECM uses signals from the vehicle speed sensor to detect the actual gear position (1st, 2nd, 3rd, 4th or 5th gear).
Then the ECM compares the actual gear with the shift schedule in the ECM memory to detect mechanical problems of the shift solenoid valves, valve body or automatic transaxle (clutch, brake or gear, etc.).
DTC No.
DTC Detection Condition
Trouble Area
P0746
The gear required by the ECM does not match the actual gear when driving (2-trip detection logic)
  1. Shift solenoid valve SL1 remains open or closed
  2. Valve body is blocked
  3. Automatic transaxle (clutch, brake or gear, etc.)

MONITOR DESCRIPTION

The ECM commands gear shifts by turning the shift solenoid valves "ON/OFF". According to the input shaft revolution, intermediate (counter) shaft revolution and output shaft revolution, the ECM detects the actual gear position (1st, 2nd, 3rd, 4th or 5th gear position). When the gear position commanded by the ECM and the actual gear position are not the same, the ECM illuminates the MIL.

HINT:
Example:
When either condition (a) or (b) is met, the ECM detects a malfunction.
(a) The ECM commands the 1st gear, but the actual gear is 2nd.
(b) The ECM commands the 2nd gear, but the actual gear is 1st.


INSPECTION PROCEDURE

HINT:
Using Intelligent tester to perform Active Test allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Test early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Test.


PERFORM ACTIVE TEST
  1. Warm up the engine.

  2. Turn the ignition switch off.

  3. Connect Intelligent tester to the DLC3.

  4. Turn the ignition switch on (IG).

  5. Turn on the tester.

  6. Select the item "Powertrain / Engine and ECT / Active Test / Shift Status".

  7. According to the display on the tester, perform the "Active Test".

    HINT:
    While driving, the shift position can be forcibly changed with Intelligent tester.
    Comparing the shift position commanded by the Active Test with the actual shift position enables you to confirm the problem (Click here).
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Control the Shift Position
    [Test Details]
    Operate the shift solenoid valve and set each shift position by yourself.
    [Vehicle Condition]
    1. IDL: ON
    2. Less than 50 km/h (31 mph)
    [Others]
    1. Press "→" button: Shift up
    2. Press "←" button: Shift down
    1st/2nd/3rd/4th/5th
    Possible to check the operation of the shift solenoid valves.

    HINT:
    1. This test can be conducted when the vehicle speed is 50 km/h (31 mph) or less.
    2. The shift position commanded by the ECM is shown in the Data List / Shift Status display on Intelligent tester.


1. CHECK OTHER DTCS OUTPUT (IN ADDITION TO DTC P0746)
  1. Connect Intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG) and turn the Intelligent tester main switch ON.

  1. When you use Intelligent tester:Select the item "Powertrain / Engine and ECT / DTC / Current or Pending".

  1. Read the DTCs using Intelligent tester.

    Result:
    Result
    Proceed to
    P0746
    A
    P0746 and other DTCs
    B

    HINT:
    If any other codes besides "P0746" are output, perform the troubleshooting for those DTCs first.



B
GO TO DTC CHART (Click here)
A


2. INSPECT SHIFT SOLENOID VALVE (SL1)

  1. G020767E88
    Remove the shift solenoid valve SL1.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    20°C (68°F)
    5.0 to 5.6 Ω

  1. Connect the positive (+) lead with a 21 W bulb to terminal 2 and the negative (-) lead to terminal 1 of the solenoid valve connector, then check the movement of the valve.

    OK:
    The solenoid makes an operating sound.



NG
REPLACE SHIFT SOLENOID VALVE (SL1) (Click here)
OK


3. INSPECT TRANSMISSION VALVE BODY ASSEMBLY

OK:
There are no foreign objects on each valve and they operate smoothly.



NG
REPAIR OR REPLACE TRANSMISSION VALVE BODY ASSEMBLY (Click here)
OK


4. INSPECT TORQUE CONVERTER CLUTCH ASSEMBLY

OK:
The torque converter clutch operates normally.



NG
REPLACE TORQUE CONVERTER CLUTCH ASSEMBLY (Click here)
OK

REPAIR OR REPLACE AUTOMATIC TRANSAXLE ASSEMBLY (Click here)


← P0741 Torque Converter Clutch Solenoid Performance (Shift Solenoid Valve DSL) (from Jul 2010)P0746 Pressure Control Solenoid "A" Performance (Shift Solenoid Valve SL1) (Aug 2008 – Jun 2010) →