2007-2013 Highlander Kluger · Service Manual TRANSMISSION

P0724 Brake Switch "B" Circuit High

Diagnostic trouble codes · Vehicles built Aug 2008 – Jun 2010

Versions by build date: May 2007 – Jul 2008 Aug 2008 – Jun 2010 from Jul 2010

DESCRIPTION

The purpose of this circuit is to prevent the engine from stalling while driving in lock-up condition when brakes are suddenly applied.
When the brake pedal is depressed, this switch sends a signals to the ECM. Then the ECM cancels the operation of the lock-up clutch while braking is in progress.
DTC No.
DTC Detection Condition
Trouble Area
P0724
The stop light switch remains ON even when the vehicle is driven in a STOP (less than 3 km/h (2 mph) and GO (30 km/h (19 mph) or more) fashion 5 times. (2-trip detection logic).
  1. Short in stop light switch circuit
  2. Stop light switch
  3. ECM

MONITOR DESCRIPTION

This DTC indicates that the stop light switch remains on. When the stop light switch remains ON during "stop and go" driving, the ECM interprets this as a fault in the stop light switch and the MIL comes on and the ECM stores the DTC. The vehicle must stop (less than 3 km/h (2 mph)) and go (30 km/h (19 mph) or more) 5 times for two driving cycles in order to detect a malfunction.

WIRING DIAGRAM

Click here.

INSPECTION PROCEDURE


1. READ VALUE USING DATA LIST

HINT:
Using Intelligent tester to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

  1. Warm up the engine.

  1. Turn the ignition switch off.

  1. Connect Intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG).

  1. Turn on the tester.

  1. Select the item "Powertrain / Engine and ECT / Data List".

  1. According to the display on the tester, read the "Data List".

    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Stop Light Switch
    Stop light switch Status/
    ON or OFF
    Brake Pedal is depressed: ON
    Brake Pedal is released: OFF
    -

    NOTICE:
    In the table below, the value listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether apart is faulty or not.

    Result:
    Result
    Proceed to
    NG
    A
    OK
    B



B
Go to step 3
A


2. INSPECT STOP LIGHT SWITCH ASSEMBLY

  1. C168528E01
    Remove the stop light switch assembly.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Switch position
    Specified Condition
    1 - 2
    Switch pin free
    Below 1 Ω
    ↑
    Switch pin pushed in
    10 kΩ or higher
    3 - 4
    Switch pin free
    10 kΩ or higher
    ↑
    Switch pin pushed in
    Below 1 Ω



NG
REPLACE STOP LIGHT SWITCH ASSEMBLY (Click here)
OK


3. CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - ECM)

  1. C168529E02
    Install the stop light switch assembly.

  1. Measure the voltage according to the value(s) in the table below when the brake pedal is depressed and released.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    D31-15 (STP) - Body ground
    Brake pedal is depressed
    11 to 14 V
    Brake pedal is released
    Below 1 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM (for 2GR-FE) (Click here)


← P0724 Brake Switch "B" Circuit High (May 2007 – Jul 2008)P0724 Brake Switch "B" Circuit High (from Jul 2010) →