2007-2013 Highlander Kluger · Service Manual TRANSMISSION

Transmission Control Switch Circuit

Circuit diagnosis · Vehicles built from Jul 2010

Versions by build date: May 2007 – Jul 2008 Aug 2008 – Jun 2010 from Jul 2010

DESCRIPTION

When moving the shift lever into the S position using the transmission control switch, it is possible to switch the shift range position between "1" (first range) and "5" (fifth range).
Shifting up "+" once raises one shift range position, and shifting down "-" lowers one shift range position.

WIRING DIAGRAM

C171936E06

INSPECTION PROCEDURE


1. CHECK HARNESS AND CONNECTOR (BATTERY - SHIFT LOCK CONTROL UNIT ASSEMBLY)

  1. C168574E03
    Disconnect the transmission control switch connector of shift lock control unit assembly.

  1. Turn the ignition switch on (IG), and measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    3 - Body ground
    Ignition switch on (IG)
    11 to 14 V
    ↑
    Ignition switch off
    Below 1 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


2. CHECK HARNESS AND CONNECTOR (SHIFT LOCK CONTROL UNIT ASSEMBLY - BODY GROUND)

  1. C168574E03
    Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    5 - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3. INSPECT SHIFT LOCK CONTROL UNIT ASSEMBLY

  1. C168599E03
    Measure the resistance between each terminal of shift lock control unit assembly when the shift lever is moved to each position.

    Standard resistance (Check for short):
    Tester Connection
    Shift Position
    Specified Condition
    3 - 7
    S, "+" and "-"
    Below 1 Ω
    ↑
    Except S, "+" and "-"
    10 kΩ or higher
    2 - 5
    Press continuously
    "+"
    (Up shift)
    Below 1 Ω
    ↑
    S
    10 kΩ or higher
    1 - 5
    Press continuously
    "-"
    (Down shift)
    Below 1 Ω
    ↑
    S
    10 kΩ or higher



NG
REPLACE SHIFT LOCK CONTROL UNIT ASSEMBLY (Click here)
OK


4. CHECK HARNESS AND CONNECTOR (SHIFT LOCK CONTROL UNIT ASSEMBLY - ECM)

  1. C227913E04
    Connect the transmission control switch connector of shift lock control unit assembly.

  1. Disconnect the ECM connector.

  1. Measure the voltage according to the value(s) in the table below when the shift lever is moved to each position.

    Standard voltage:
    Tester Connection
    Shift Position
    Specified Condition
    D55-24 (S) -
    Body ground
    S, "+" and "-"
    11 to 14 V
    ↑
    Except S, "+" and "-"
    Below 1 V

  1. C227913E06
    Turn the ignition switch off.

  1. Measure the resistance according to the value(s) in the table below when the shift lever is moved to each position.

    Standard resistance:
    Tester Connection
    Shift Position
    Specified Condition
    D55-16 (SFTU) - Body ground
    Press continuously "+" (Up shift)
    Below 1 Ω
    ↑
    S
    10 kΩ or higher
    D55-22 (SFTD) - Body ground
    Press continuously "-" (Down shift)
    Below 1 Ω
    ↑
    S
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE


← Transmission Control Switch Circuit (Aug 2008 – Jun 2010)Pattern Select Switch Circuit (May 2007 – Jun 2010) →