2007-2013 Highlander Kluger · Service Manual TRANSMISSION

INSTALLATION

Removal / installation · Vehicles built Aug 2008 – Jun 2010

Versions by build date: May 2007 – Jul 2008 Aug 2008 – Jun 2010 from Jul 2010


1. INSTALL SPEED SENSOR (NC SENSOR)

  1. C090570
    Coat a new O-ring with ATF.

  1. Install the speed sensor with the bolt.

    Torque:
    11 N*m{ 112 kgf*cm , 8 ft.*lbf }

    HINT:
    Make sure to install the same manufacturer's sensor.

  1. Connect the speed sensor connector.


2. INSTALL SPEED SENSOR (NT SENSOR)

  1. C090569
    Coat a new O-ring with ATF.

  1. Install the speed sensor with the bolt.

    Torque:
    11 N*m{ 112 kgf*cm , 8 ft.*lbf }

    HINT:
    Make sure to install the same manufacturer's sensor.

  1. Connect the speed sensor connector.


3. INSTALL AIR CLEANER BRACKET

  1. A171820
    Install the 2 bolts and air cleaner bracket.

    Torque:
    12 N*m{ 123 kgf*cm , 9 ft.*lbf }


4. INSTALL AIR CLEANER CASE SUB-ASSEMBLY

  1. A170450
    Install the air cleaner case with the 3 bolts.

    Torque:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }

  1. Connect the hose and connector.


5. INSTALL AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY

6. INSTALL AIR CLEANER CAP SUB-ASSEMBLY

  1. A171941E01
    Install the air cleaner filter element, align the groove on the air cleaner hose with the throttle body alignment tab and tighten the clamp as shown in the illustration.

    HINT:
    1. A = 30°
    2. B = 11 to 14 mm (0.433 in. to 0.551 in.)

  1. Install the air cleaner cap with the 2 bolts and clips.

    Torque:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }

  1. A170887
    Connect the 3 vacuum hoses.

  1. A171944
    Connect the mass air flow meter connector.

  1. Connect the No. 2 ventilation hose and fuel vapor feed hose assembly.


7. INSTALL NO. 1 AIR CLEANER INLET

  1. A170454E01
    Install the No. 1 air cleaner inlet with the 2 bolts.

    Torque:
    7.0 N*m{ 71 kgf*cm , 62 in.*lbf } [A]

    Torque:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf } [B]

  1. Connect the 2 vacuum hoses.


8. INSTALL NO. 2 AIR CLEANER INLET

  1. A170453
    Install the No. 2 air cleaner inlet with the 2 bolts.

    Torque:
    7.0 N*m{ 71 kgf*cm , 62 in.*lbf }

  1. Connect the 2 vacuum hoses and harness clamps.


9. REMOVE COOL AIR INTAKE DUCT SEAL

  1. A170196
    Install the cool air intake duct seal with the 11 clips.


10. INSTALL BATTERY

  1. A171858E01
    Install the battery tray and battery.

  1. Install the battery clamp with the bolt and nut.

    Torque:
    Bolt:
    5.4 N*m{ 55 kgf*cm , 48 in.*lbf }
    Nut A:
    5.4 N*m{ 55 kgf*cm , 48 in.*lbf }
    Nut B:
    13 N*m{ 131 kgf*cm , 9 ft.*lbf }
    Nut C:
    6.4 N*m{ 64 kgf*cm , 57 in.*lbf }

  1. Install the positive battery terminal and nut.

  1. Connect the negative battery terminal, and tighten the nut.


11. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).

← INSTALLATION (May 2007 – Jul 2008)INSTALLATION (from Jul 2010) →