2007-2013 Highlander Kluger · Service Manual TRANSMISSION

INSTALLATION

Removal / installation · Vehicles built Aug 2008 – Jun 2010

Versions by build date: May 2007 – Jul 2008 Aug 2008 – Jun 2010 from Jul 2010


1. INSTALL TRANSMISSION WIRE

  1. D030867
    Coat a new O-ring of the transmission wire connector with ATF and install it.

  1. D030866
    Install the transmission wire with the bolt.

    Torque:
    5.4 N*m{ 55 kgf*cm , 48 in.*lbf }


2. CONNECT TRANSMISSION WIRE

  1. C091927E08
    Coat a new O-ring of the ATF temperature sensor with ATF.

  1. Install the ATF temperature sensor with the lock plate and bolt.

    Torque:
    6.6 N*m{ 67 kgf*cm , 58 in.*lbf }

  1. Connect the 7 shift solenoid valve connectors.


3. INSTALL AUTOMATIC TRANSAXLE OIL PAN SUB-ASSEMBLY

  1. D030865E03
    Install the 2 magnets in the oil pan.

  1. Apply adhesive to the 18 bolts.

    Adhesive:
    Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent

  1. C091925
    Using a new gasket, install the oil pan to the transaxle case with the 18 bolts.

    Torque:
    7.8 N*m{ 80 kgf*cm , 69 in.*lbf }

    NOTICE:
    Apply adhesive to the bolts and tighten them within 10 minutes of application.


4. INSTALL AUTOMATIC TRANSAXLE ASSEMBLY

HINT:
(Click here)


5. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).


6. ADD AUTOMATIC TRANSAXLE FLUID

7. INSPECT AUTOMATIC TRANSAXLE FLUID

HINT:
Drive the vehicle so that the engine and transaxle are at normal operating temperature.

Fluid temperature:
70 to 80°C (158 to 176°F)

  1. Park the vehicle on a level surface and set the parking brake.

  1. D025120E05
    With the engine idling and the brake pedal depressed, move the shift lever to all positions from P to S1 and return to the P position.

  1. Take out the dipstick and wipe it clean.

  1. Put the dipstick back all the way.

  1. Take out the dipstick again and check that the fluid level is within the HOT range.
    If the fluid level is below the HOT range, add new fluid and recheck the fluid level.
    If the fluid level exceeds the HOT range, drain the fluid once, add the proper amount of new fluid and recheck the fluid level.
    If there are leaks, it is necessary to repair or replace O-rings, FIPGs, oil seals, plugs and/or other parts.


8. INSPECT FOR TRANSAXLE FLUID LEAK

9. INSTALL NO. 2 ENGINE UNDER COVER

  1. A171854
    Install the No. 2 engine under cover with the 2 bolts.


10. INSTALL NO. 1 ENGINE UNDER COVER

  1. A171855
    Install the No. 1 engine under cover with the 6 bolts and 2 clips.


11. INSTALL ENGINE UNDER COVER ASSEMBLY

  1. A171850
    Install the engine under cover assembly with the 2 bolts, 2 screws and 5 clips.

  1. A171849
    Install the engine under cover assembly RR with the 2 bolts.


12. RESET MEMORY

HINT:
(Click here)

← INSTALLATION (May 2007 – Jul 2008)INSTALLATION (from Jul 2010) →