2007-2013 Highlander Kluger · Service Manual BODY ELECTRICAL

B15C2 Speed Signal Malfunction

Diagnostic trouble codes · Vehicles built from Jul 2012

Versions by build date: Jul 2010 – Jun 2012 from Jul 2012

DESCRIPTION

The navigation receiver assembly receives a vehicle speed signal from the combination meter assembly and information from the navigation antenna assembly, and then adjusts vehicle position.
The navigation receiver assembly stores this DTC when the difference between the speed information that the navigation antenna assembly receives and the SPD pulse received from the combination meter assembly becomes large.

HINT:
  1. A voltage of 12 V or 5 V is output from each ECU and then input to the combination meter assembly. The signal is changed to a pulse signal at the transistor in the combination meter assembly. Each ECU controls the respective systems based on the pulse signal.
  2. If a short occurs in any of the ECUs or in the wire harness connected to an ECU, all systems in the diagram below will not operate normally.

DTC No.
DTC Detection Condition
Trouble Area
B15C2
A difference between the GPS speed and SPD pulse is detected.
  1. Combination meter assembly
  2. Wire harness or connector
  3. Junction connector
  4. Navigation receiver assembly

WIRING DIAGRAM

E211393E01

INSPECTION PROCEDURE


1. CHECK VEHICLE SENSOR (OPERATION CHECK)

  1. E176549
    Enter the "Check GPS & Vehicle Sensor" (Vehicle Sensors) (Click here).

  1. While driving the vehicle, compare the "Speed" indicator to the reading on the speedometer. Check if these readings are almost equal.

    OK:
    The readings are almost equal.



NG
Go to step 2
OK

REPLACE NAVIGATION RECEIVER ASSEMBLY (Click here)

2. INSPECT COMBINATION METER ASSEMBLY (OUTPUT WAVEFORM)

  1. E152386E16
    Check the output waveform.
    1. Remove the combination meter assembly with the connector(s) still connected.

    2. Connect an oscilloscope to terminal E1-9 (+S) and body ground.

    3. Turn the ignition switch ON.

    4. Turn a wheel slowly.

    5. Check the signal waveform according to the condition(s) in the table below.

      Item
      Condition
      Measurement terminal
      E1-9 (+S) - Body ground
      Tool setting
      5 V/DIV., 20 ms./DIV.
      Vehicle condition
      Wheel being rotated
      Text in Illustration 
      *a
      Component with harness connected
      (Combination Meter Assembly)

      OK:
      The waveform is similar to that shown in the illustration.

      HINT:
      When the system is functioning normally, one wheel revolution generates 4 pulses. As the vehicle speed increases, the width indicated by (A) in the illustration narrows.



NG
GO TO METER / GAUGE SYSTEM (Click here)
OK


3. CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - COMBINATION METER ASSEMBLY)
  1. Disconnect the E4 navigation receiver assembly connector.

  1. Disconnect the E1 combination meter assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    E4-3 (SPD) - E1-9 (+S)
    Always
    Below 1 Ω



NG
Go to step 4
OK

REPLACE NAVIGATION RECEIVER ASSEMBLY (Click here)

4. CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - JUNCTION CONNECTOR)
  1. Disconnect the E4 navigation receiver assembly connector.

  1. Disconnect the E17 junction connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    E4-3 (SPD) - E17-7
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - JUNCTION CONNECTOR)
OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (JUNCTION CONNECTOR)


← B15C2 Speed Signal Malfunction (Jul 2010 – Jun 2012)B15E1 Media Malfunction (from Jul 2010) →