2007-2013 Highlander Kluger · Service Manual TRANSMISSION

REASSEMBLY

Removal / installation · Vehicles built from May 2007


1. INSTALL FRONT DIFFERENTIAL SIDE GEAR

  1. C050242
    Apply ATF to the 2 front differential side gears, 2 side gear thrust washers, 2 front differential pinions and 2 pinion thrust washers and install them to the differential case.


2. INSTALL NO. 1 FRONT DIFFERENTIAL PINION SHAFT

  1. C050241E06
    Coat the No. 1 front differential pinion shaft with ATF, and install it to the differential case.


3. INSPECT BACKLASH

  1. C050252
    Using a dial indicator, inspect the backlash of the side gear.

    Standard backlash:
    0.05 to 0.20 mm (0.0020 to 0.0079 in.)

    Thrust washer thickness 
    Mark
    Thickness
    -
    1.625 mm (0.0640 in.)
    -
    1.725 mm (0.0679 in.)
    -
    1.825 mm (0.0719 in.)


4. INSTALL FRONT DIFFERENTIAL PINION SHAFT STRAIGHT PIN

  1. C050253
    Using a pin punch and a hammer, install the pinion shaft straight pin.

  1. C050254
    Using a chisel and a hammer, stake the differential case.

    NOTICE:
    Stake the differential case after adjusting the backlash.


5. INSTALL FRONT DIFFERENTIAL CASE FRONT TAPERED ROLLER BEARING

  1. D026447E01
    Using SST and a press, install the front differential case front tapered roller bearing to the differential case.
    SST
    09316-12010  
    09550-60010   (09951-00490)
    09950-70010   (09951-07100)

    NOTICE:
    Do not damage the bearing cage when installing the bearing inner race.

  1. C083736
    Using SST and a hammer, install the front differential case tapered roller bearing front outer race to the transaxle housing.
    SST
    09550-60010   (09951-00490)
    09950-60020   (09951-00910)


6. INSTALL FRONT DIFFERENTIAL CASE REAR TAPERED ROLLER BEARING

  1. D026448E02
    Using SST and a press, install the front differential case front tapered roller bearing to the differential case.
    SST
    09316-12010  
    09550-60010   (09951-00490)
    09950-70010   (09951-07100, 09951-07150)

    NOTICE:
    Do not damage the bearing cage when installing the bearing inner race.

  1. D026449E01
    Using SST and a hammer, install the front differential case tapered roller bearing rear outer race to the transaxle housing.
    SST
    09950-70010   (09951-07100, 09951-07150)
    09950-60020   (09951-00890)

    NOTICE:
    No clearance is allowed between the bearing and transaxle housing.


7. ADJUST DIFFERENTIAL SIDE BEARING PRELOAD

  1. D026450
    Install the differential assembly to the transaxle case.

  1. C115282E01
    Clean the mating surfaces of the transaxle case and transaxle housing.

  1. Install the transaxle housing to the transaxle case and tighten them with the 16 bolts.

    Torque:
    Bolt A:
    25 N*m{ 255 kgf*cm , 18 ft.*lbf }
    Bolt B:
    33 N*m{ 337 kgf*cm , 24 ft.*lbf }
    Bolt C:
    29 N*m{ 295 kgf*cm , 21 ft.*lbf }
    Bolt D:
    28 N*m{ 286 kgf*cm , 21 ft.*lbf }

    HINT:
    Apply adhesive or equivalent to bolts A and D.

    Adhesive:
    Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent

    Bolt length:
    Bolt A, B:
    50 mm (1.969 in.)
    Bolt C:
    42 mm (1.654 in.)
    Bolt D:
    72 mm (2.835 in.)

    NOTICE:
    Apply adhesive to the bolts and tighten them within 10 minutes of application.

    HINT:
    Bolt A is a non-reusable bolt. However, bolt A can be used after cleaning it.

  1. D025604E01
    Using SST, turn the differential assembly to the right and left 2 or 3 times to settle the bearing.
    SST
    09564-32011  

  1. Using SST and a torque wrench, measure the turning torque of the differential.

    SST
    09564-32011  

    Turning torque at 60 rpm:
    New bearing:
    0.20 to 0.69 N*m (2.0 to 7.0 kgf*cm, 1.8 to 6.1 in.*lbf)
    Used bearing:
    0.10 to 0.35 N*m (1.0 to 3.6 kgf*cm, 0.9 to 3.1 in.*lbf)

    HINT:
    If the turning torque is not as specified, refer to the table below to select a thrust washer so that the specified value is achieved.

    Flange thickness: mm (in.) 
    Mark
    Thickness
    Mark
    Thickness
    0
    2.000 (0.0787)
    9
    2.450 (0.0965)
    j
    2.025 (0.0797)
    T
    2.475 (0.0974)
    1
    2.050 (0.0807)
    A
    2.500 (0.0984)
    K
    2.075 (0.0817)
    U
    2.525 (0.0994)
    2
    2.100 (0.0827)
    B
    2.550 (0.1004)
    L
    2.125 (0.0837)
    V
    2.575 (0.1014)
    3
    2.150 (0.0846)
    C
    2.600 (0.1024)
    M
    2.175 (0.0857)
    W
    2.625 (0.1034)
    4
    2.200 (0.0866)
    D
    2.650 (0.1043)
    N
    2.225 (0.0876)
    X
    2.675 (0.1053)
    5
    2.250 (0.0886)
    E
    2.700 (0.1063)
    P
    2.275 (0.0896)
    Y
    2.725 (0.1073)
    6
    2.300 (0.0906)
    F
    2.750 (0.1083)
    Q
    2.325 (0.0915)
    AA
    2.775 (0.1093)
    7
    2.350 (0.0925)
    G
    2.800 (0.1102)
    R
    2.375 (0.0935)
    AB
    2.825 (0.1112)
    8
    2.400 (0.0945)
    H
    2.850 (0.1122)
    S
    2.425 (0.0954)
    -
    -

  1. C115282
    Remove the 16 bolts and the transaxle housing.

  1. D026450
    Remove the differential assembly.


8. INSTALL FRONT DIFFERENTIAL RING GEAR

  1. D025215E07
    Using ATF and heater, heat the front differential ring gear to 90 to 110°C (194.0 to 230.0°F).

    NOTICE:
    Do not heat the ring gear to more than 110°C (230.0°F).

  1. Clean the contact surface of the front differential case.

  1. D026445E08
    Align the matchmarks, and install the front differential ring gear case quickly.

    NOTICE:
    Do not install the bolts while the ring gear is hot.

  1. D026446
    Tighten the 14 bolts.

    Torque:
    95 N*m{ 970 kgf*cm , 70 ft.*lbf }

    NOTICE:
    Tighten the bolts a little at a time in a diagonal pattern.


9. INSTALL TRANSAXLE HOUSING OIL SEAL

  1. C083054E04
    Using SST and a hammer, install a new oil seal.
    SST
    09316-60011   (09316-00011)

  1. Coat the lip of oil seal with a little MP grease.

    Oil seal installation depth:
    -0.5 to 0.5 mm (-0.020 to 0.020 in.)


10. INSTALL DIFFERENTIAL SIDE BEARING RETAINER OIL SEAL

  1. C083053E01
    Using SST and a hammer, install a new oil seal.
    SST
    09223-15020  
    09950-70010   (09951-07150)

  1. Coat the lip of the oil seal with a little MP grease.

    Oil seal installation depth:
    -0.5 to 0.2 mm (-0.020 to 0.008 in.)

← INSPECTION (from May 2007)PRECAUTION (May 2007 – Jul 2008) →