2007-2013 Highlander Kluger · Service Manual SERVICE SPECIFICATIONS

SERVICE DATA

Specifications · Vehicles built May 2007 – Jun 2010

Versions by build date: May 2007 – Jun 2010 from Jul 2010

Camshaft timing oil control valve assembly
1 - 2
6.9 to 7.9 Ω at 20°C (68°F)
Throttle body
2 (M+) - 1 (M-)
0.3 to 100 kΩ at 20°C (68°F)
Duty vacuum switching valve
1 - 2
19 to 21 Ω at at 20°C (68°F)
Acceleration pedal assembly
Accelerator Position No. 1
Accelerator pedal is released:
0.5 to 1.1 V
Accelerator pedal is depressed:
2.5 to 4.5 V
Accelerator Position No. 2
Accelerator pedal is released:
1.2 to 2.0 V
Accelerator pedal is depressed:
3.4 to 5.0 V
Mass air flow meter
Standard Condition
Below 0.69 g/s
Crankshaft position sensor
1 - 2
1630 to 2740 Ω at -10 to 50 °C (14 to 122 °F)
2065 to 3225 Ω at 50 to 100 °C (122 to 212 °F)
Engine coolant temperature sensor
1 - 2
2.32 to 2.59 kΩ at approx. 20°C (68°F)
0.310 to 0.326 kΩ at approx. 80°C (176°F)
Knock control sensor
1 - 2
120 to 280 kΩ at 25°C (77°F)
Air fuel ratio sensor
(for Bank 1)
1 (HA1A) - 2 (+B)
1.8 to 3.4 Ω at 20°C (68°F)
1 (HA1A) - 4 (A1A-)
10 kΩ or higher (always)
Air fuel ratio sensor
(for Bank 2)
1 (HA2A) - 2 (+B)
1.8 to 3.4 Ω at 20°C (68°F)
1 (HA2A) - 4 (A2A-)
10 kΩ or higher (always)
Heated oxygen sensor
(for Bank 1)
2 (HT1B) - 1 (+B)
11 to 16 Ω at 20°C (68°F)
2 (HT1B) - 3 (E2)
10 kΩ or higher (always)
Heated oxygen sensor
(for Bank 2)
1 (HT2B) - 2 (+B)
11 to 16 Ω at 20°C (68°F)
1 (HT2B) - 4 (E2)
10 kΩ or higher (always)
Integration relay
(EFI relay)
(2E-12) - (2E-7)
10 kΩ or higher
(No battery voltage applied)
(2E-12) - (2E-7)
Below 1 Ω
(Battery voltage applied to terminals 2E-10 and 2E-9)
Integration relay
(C/OPN relay)
(2E-13) - (2E-7)
10 kΩ or higher
(No battery voltage applied)
(2E-13) - (2E-7)
Below 1 Ω
(Battery voltage applied to terminals 2E-8 and 2D-12)
Integration relay
(A/F relay)
(2A-4) - (2C-1)
10 kΩ or higher
(No battery voltage applied)
(2A-4) - (2C-1)
Below 1 Ω
(Battery voltage applied to terminals 2E-10 and 2E-7)
Ignition relay No. 1
3 - 5
10 kΩ or higher
(No battery voltage applied)
3 - 5
Below 1 Ω
(Battery voltage applied to terminals 1 and 2)
Ignition relay No. 2
3 - 5
10 kΩ or higher
(No battery voltage applied)
3 - 5
Below 1 Ω
(Battery voltage applied to terminals 1 and 2)
Fuel pump relay
3 - 4
Below 1 Ω
(No battery voltage applied)
3 - 4
10 kΩ or higher
(Battery voltage applied to terminals 1 and 2)
3 - 5
10 kΩ or higher
(No battery voltage applied)
3 - 5
Below 1 Ω
(Battery voltage applied to terminals 1 and 2)
← HOW TO DETERMINE NUT STRENGTH (from May 2007)SERVICE DATA (from Jul 2010) →