2007-2013 Highlander Kluger · Service Manual TRANSMISSION

REASSEMBLY

Removal / installation · Vehicles built from May 2007


1. INSTALL OVERDRIVE DIRECT CLUTCH O-RING

  1. D026464E01
    Coat a new O-ring with ATF and install it to the direct clutch drum.

    NOTICE:
    Make sure that the O-ring is not twisted or pinched when it is installed.


2. INSTALL OVERDRIVE DIRECT CLUTCH DRUM SUB-ASSEMBLY

  1. D026462E05
    Coat the direct clutch drum with ATF and install it to the intermediate shaft.

    NOTICE:
    1. Be careful not to damage the O-ring.
    2. Be careful not to damage the lip of the direct clutch drum.


3. INSTALL OVERDRIVE DIRECT CLUTCH PISTON

  1. D026461E03
    Coat the overdrive direct clutch piston with ATF, and install it to the direct clutch drum.


4. INSTALL OVERDRIVE CLUTCH RETURN SPRING SUB-ASSEMBLY

  1. D026423E05
    Install the overdrive clutch return spring to the direct clutch drum.

    NOTICE:
    After installing the spring sub-assembly, check that all of the springs are engaged in the piston correctly.

  1. Coat the clutch balancer with ATF.

  1. D026424E05
    Install the clutch balancer to the direct clutch drum.

    NOTICE:
    1. Be careful not to damage the lip of the direct clutch balancer.
    2. Make sure that the lip of the seal is not pinched and that it has no other defects.
    3. Apply sufficient ATF to the sealing lip before installing the clutch balancer.

  1. D003677E01
    Place SST on the clutch balancer and compress the overdrive clutch return spring with a press.
    SST
    09387-00020  

  1. Using a snap ring expander, install the snap ring to the direct clutch drum.

  1. Be sure that the end gap of the snap ring is not aligned with the spring retainer claw.

    NOTICE:
    1. Stop the press when the spring seat is lowered to the place 1 to 2 mm (0.039 to 0.078 in.) from the snap ring groove. This prevents the spring seat from being deformed.
    2. Do not expand the snap ring excessively.

  1. D025588E02
    Set the end gap of the snap ring in the piston as shown in the illustration.

    NOTICE:
    The end gap of the snap ring should not align with any of the stoppers.


5. INSTALL OVERDRIVE DIRECT CLUTCH DISC

  1. D026417E01
    Coat the 4 discs with ATF.

  1. Install the 4 plates, 4 discs, and flange to the intermediate shaft.

    NOTICE:
    Make sure that the plates, discs, and flange are installed as shown in the illustration.

  1. D026421E01
    Using a screwdriver, install the snap ring.

  1. Check that the end gap of the snap ring is not aligned with one of the cutouts.

    NOTICE:
    The snap ring should be fully engaged in the groove of the drum.


6. INSTALL DIRECT MULTIPLE CLUTCH DISC

  1. D026416E03
    Coat the 3 discs with ATF.

  1. Install the cushion plate, 3 plates, 3 discs, and flange to the intermediate shaft.

    NOTICE:
    1. Install the cushion plate with the mark on the white surface facing to plate.
    2. Make sure that the discs, plates, and flange are installed in the correct order.

  1. D026419E03
    Using a screwdriver, install the snap ring.

  1. Check that the end gap of the snap ring is not aligned with one of the cutouts.

    NOTICE:
    The snap ring should be fully engaged in the groove of the drum.

← INSPECTION (from May 2007)COMPONENTS (from May 2007) →