2007-2013 Highlander Kluger · Service Manual HEATER & AIR CONDITIONING SYSTEM

TERMINALS OF ECU

System information · Vehicles built May 2007 – Jun 2010

Versions by build date: May 2007 – Jun 2010 from Jul 2010


CHECK AIR CONDITIONING AMPLIFIER
E127561E04
  1. Measure the voltage of the connectors.

    HINT:
    Check from the rear of the connector while it is connected to the air conditioning amplifier.

    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    D33-1 (IG+) - D33-14 (GND)
    GR - W-B
    Power source (IG)
    Ignition switch on (IG)
    11 to 14 V
    D33-2 (SOL+) - D33-14 (GND)
    L - W-B
    Air conditioning compressor operation signal
    Engine idling
    Pulse generation
    (see waveform 1)
    Blower switch LO
    Air Conditioning switch ON
    D33-3 (PTC1) - Body ground (*1)
    P - Body ground
    PTC NO. 1 heater relay operation signal
    Engine idling
    Below 1 V → 11 to 14 V
    Set temperature: MAX HOT
    Engine coolant temperature: Below 65°C (149°F)
    Ambient temperature: Below 10°C (50°F)
    Blower switch OFF → LO
    D33-4 (PTC3) - Body ground (*1)
    W - Body ground
    PTC NO. 3 heater relay operation signal
    Engine idling
    Below 1 V → 11 to 14 V
    Set temperature: MAX HOT
    Engine coolant temperature: Below 65°C (149°F)
    Ambient temperature: Below 10°C (50°F)
    Blower switch OFF → LO
    D33-5 (TAM) - D33-14 (GND)
    B - W-B
    Ambient temperature sensor signal
    Ignition switch on (IG)
    1.8 to 2.2 V
    Ambient temperature: 25°C (77°F)
    D33-8 (LOCK) - D33-14 (GND)
    V - W-B
    Air compressor lock sensor signal
    Engine idling
    Pulse generation
    (see waveform 5)
    Air Conditioning switch ON
    Blower switch LO
    D33-9 (PRE) - D33-13 (SG-2)
    R - SB
    Air conditioning pressure sensor signal
    Refrigerant pressure: Normal
    0.76 to 4.74 V
    D33-9 (PRE) - D33-13 (SG-2)
    R - SB
    Air conditioning pressure sensor signal
    Refrigerant pressure: Abnormal (less than 0.196 MPa [2.0 kgf/cm2, 28 psi])
    0.5 to 4.83 V
    D33-9 (PRE) - D33-13 (SG-2)
    R - SB
    Air conditioning pressure sensor signal
    Refrigerant pressure: Abnormal (more than 3.03 MPa [32 kgf/cm2, 455 psi])
    4.74 V or higher
    D33-10 (S5-3) - D33-14 (GND)
    O - W-B
    Power supply for pressure sensor
    Ignition switch on (IG)
    4.5 to 5.5 V
    D33-11 (CANH) - D33-14 (GND)
    LG - W-B
    Hi-level CAN bus line
    Ignition switch on (IG)
    Pulse generation
    (see waveform 3)
    D33-12 (CANL) - D33-14 (GND)
    W - W-B
    Lo-level CAN bus line
    Ignition switch on (IG)
    Pulse generation
    (see waveform 4)
    D33-13 (SG-2) - Body ground
    SB - Body ground
    Ground for pressure sensor
    Always
    Below 1 V
    D33-14 (GND) - Body ground
    W-B - Body ground
    Ground for main power supply
    Always
    Below 1 V
    D33-20 (MGC) - D33-14 (GND)
    V - W-B
    Air conditioning compressor magnetic clutch operation signal
    Engine idling
    Below 1 V
    Blower switch LO
    Air Conditioning switch ON
    D33-21 (B) - D33-14 (GND)
    B - W-B
    Power source (Back-up)
    Always
    11 to 14 V
    D33-22 (PTC2) - Body ground (*1)
    G - Body ground
    PTC NO. 2 heater relay operation signal
    Engine idling
    Below 1 V → 11 to 14 V
    Set temperature: MAX HOT
    Engine coolant temperature: Below 65°C (149°F)
    Ambient temperature: Below 10°C (50°F)
    Blower switch OFF → LO
    D33-23 (BLW) - D33-14 (GND)
    R - W-B
    Blower motor control signal
    Ignition switch on (IG)
    Pulse generation
    (see waveform 2)
    Blower switch LO
    D33-25 (ALT) - Body ground (*1)
    SB - Body ground
    Generator signal
    Engine idling
    Pulse generation
    D33-27 (HLS) - Body ground (*1)
    V - Body ground
    Headlight signal
    Engine idling
    Below 1 V
    Headlight switch ON
    D33-29 (TR) - D33-34 (SG-4)
    BR- B
    Room temperature sensor signal (for Front)
    Ignition switch on (IG)
    1.8 to 2.2 V
    Vehicle interior temperature: 25°C (77°F)
    D33-32 (TSP) - D33-14 (GND)
    GR - W-B
    Front passenger side solar sensor signal
    Ignition switch on (IG)
    0.8 to 4.3 V
    Solar sensor subject to electric light
    D33-33 (TSD) - D33-14 (GND)
    O - W-B
    Driver side solar sensor signal
    Ignition switch on (IG)
    0.8 to 4.3 V
    Solar sensor subject to electric light
    D33-35 (SG-4) - Body ground
    LG - Body ground
    Ground for room temperature sensor (for Front)
    Always
    Below 1 V
    D33-37 (LIN1) - D33-14 (GND)
    R - W-B
    LIN communication signal
    Ignition switch on (IG)
    Pulse generation
    D33-38 (RDEF) - D33-14 (GND)
    W - W-B
    Rear defogger switch signal
    Ignition switch on (IG)
    Rear defogger switch OFF
    11 to 14 V
    D33-38 (RDEF) - D33-14 (GND)
    W - W-B
    Rear defogger switch signal
    Ignition switch on (IG)
    Rear defogger switch ON
    Below 1 V
    D34-1 (RBUS) - D34-21 (RBUG) (*2)
    R - V
    BUS IC control signal (for Rear)
    Ignition switch on (IG)
    Pulse generation
    D34-4 (TEC) - D34-19 (SGND) (*2)
    B - GR
    Evaporator temperature sensor signal (for Rear)
    Ignition switch on (IG)
    1.4 to 1.8 V
    Evaporator temperature: 15°C (59°F)
    D34-7 (SG-6) - Body ground (*3)
    W - Body ground
    Ground for room temperature sensor signal (for Rear)
    Always
    Below 1 V
    D34-13 (RLIN) - D34-20 (GND2) (*2)
    B - SB
    LIN communication signal (for Rear)
    Ignition switch on (IG)
    Pulse generation
    D34-17 (TR) - D34-7 (SG-6) (*3)
    BR - W
    Room temperature sensor signal (for Rear)
    Ignition switch on (IG)
    1.8 to 2.2 V
    Vehicle interior temperature: 25°C (77°F)
    D34-19 (SGND) - Body ground (*2)
    GR - Body ground
    Ground for evaporator temperature sensor signal (for Rear)
    Always
    Below 1 V
    D34-20 (GND2) - Body ground (*2)
    SB - Body ground
    Ground for power supply
    Always
    Below 1 V
    D34-21 (RBUG) - Body ground (*2)
    V - Body ground
    Ground for BUS IC (for Rear)
    Always
    Below 1 V
    D34-22 (BLWH) - D34-20 (GND2) (*2)
    G - SB
    Blower motor control signal (for Rear)
    Ignition switch on (IG)
    Pulse generation
    Blower switch LO
    D34-23 (RBBU) - D34-21 (RBUG) (*2)
    Y - V
    Power supply for BUS IC (for Rear)
    Ignition switch on (IG)
    11 to 14 V
    D34-24 (+B2) - D34-20 (GND2) (*2)
    LG - SB
    Power source (Back-up) (for Rear)
    Always
    11 to 14 V
    z17-2 (BUS G) - Body ground
    -
    Ground for BUS IC
    Always
    Below 1 V
    z17-3 (BUS) - a1-2 (BUS G)
    -
    BUS IC control signal
    Ignition switch on (IG)
    Pulse generation
    z17-4 (B BUS) - a1-2 (BUS G)
    -
    Power supply for BUS IC
    Ignition switch on (IG)
    11 to 14 V
    z17-5 (SG) - Body ground
    -
    Ground for evaporator temperature sensor
    Always
    Below 1 V
    z17-6 (TE) - z17-5 (SG)
    -
    Evaporator temperature sensor signal (for Front)
    Ignition switch on (IG)
    1.4 to 1.8 V
    Evaporator temperature: 15°C (59°F)

  2. E074977E11
    Using an oscilloscope, check waveform 1.
    Compressor and magnetic clutch operation signal 
    Item
    Content
    Tester Connection
    D33-2 (SOL+) - D33-14 (GND)
    Tool Setting
    5 V/DIV., 500 μsec./DIV.
    Condition
    Engine idling, Blower switch LO, air conditioning switch ON

  3. E103396E05
    Using an oscilloscope, check waveform 2.
    Blower motor control signal 
    Item
    Content
    Tester Connection
    D33-23 (BLW) - D33-14 (GND)
    Tool Setting
    1 V/DIV., 500 μsec./DIV.
    Condition
    Ignition switch on (IG), Blower switch LO

    HINT:
    When the blower level is increased, the duty ratio changes accordingly.

  4. A086154E10
    Using an oscilloscope, check waveform 3.
    CAN communication signal 
    Item
    Content
    Tester Connection
    D33-11 (CANH) - D33-14 (GND)
    Tool Setting
    1 V/DIV., 10 μsec./DIV.
    Condition
    Ignition switch on (IG)

    HINT:
    The waveform varies depending on the CAN communication signal.

  5. A086155E11
    Using an oscilloscope, check waveform 4.
    CAN communication signal 
    Item
    Content
    Tester Connection
    D33-12 (CANL) - D33-14 (GND)
    Tool Setting
    1 V/DIV., 10 μsec./DIV.
    Condition
    Ignition switch on (IG)

    HINT:
    The waveform varies depending on the CAN communication signal.

  6. E147961E01
    Using an oscilloscope, check waveform 5.
    Air Conditioning compressor lock sensor signal 
    Item
    Content
    Tester Connection
    D33-8 (LOCK) - D33-14 (GND)
    Tool Setting
    200 mV/DIV., 10 ms./DIV.
    Condition
    Engine is running
    Blower switch: LO
    Air conditioning switch: ON

    HINT:
    The waveform varies depending on the engine speed.

    *1: w/ PTC Heater
    *2: for Rear Air Conditioning
    *3: for Rear Automatic Air Conditioning


CHECK FRONT AIR CONDITIONING CONTROL
E152670E03
  1. Measure the voltage of the connectors.

    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    E8-2 (IG+) - E8-6 (GND)
    V - GR
    Power source (IG)
    Ignition switch on (IG)
    11 to 14 V
    E8-3 (LIN1) - E8-6 (GND)
    R - GR
    LIN communication signal
    Ignition switch on (IG)
    Pulse generation
    E8-6 (GND) - Body ground
    GR - Body ground
    Ground for front air conditioning control
    Always
    Below 1 V


CHECK REAR AIR CONDITIONING CONTROL (for Rear Air Conditioning)
E152670E02
  1. Measure the voltage of the connectors.

    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    R1-7 (IG+) - R1-12 (E)
    V - W-B
    Power source (IG)
    Ignition switch on (IG)
    11 to 14 V
    R1-5 (MPX-) - R1-12 (E)
    B - W-B
    LIN communication signal
    Ignition switch on (IG)
    Pulse generation
    R1-12 (E) - Body ground
    W-B - Body ground
    Ground for rear air conditioning control
    Always
    Below 1 V

← PROBLEM SYMPTOMS TABLE (from Jul 2012)TERMINALS OF ECU (from Jul 2010) →