2007-2013 Highlander Kluger · Service Manual HEATER & AIR CONDITIONING SYSTEM

B1413/13 Evaporator Temperature Sensor Circuit

Diagnostic trouble codes · Vehicles built May 2007 – Jul 2008

Versions by build date: May 2007 – Jul 2008 Aug 2008 – Jun 2010 from Jul 2010

DESCRIPTION

The NO.1 cooler thermistor (evaporator temperature sensor) is installed on the evaporator in the front air conditioning unit to detect the temperature of the cooled air that has passed through the evaporator and to control the air conditioner. It sends signals to the air conditioning amplifier. The signals change in accordance with the resistance of the NO.1 cooler thermistor (evaporator temperature sensor). As the temperature decreases, the resistance increases. As the temperature increases, the resistance decreases. The air conditioning amplifier applies a voltage (5 V) to the NO.1 cooler thermistor (evaporator temperature sensor) and reads voltage changes as changes in the resistance of the NO.1 cooler thermistor (evaporator temperature sensor). This sensor is used for frost prevention.
DTC No.
DTC Detection Condition
Trouble Area
B1413/13
Open or short in evaporator temperature sensor circuit
  1. NO.1 cooler thermistor (evaporator temperature sensor)
  2. Air conditioning harness
  3. Air conditioning amplifier

WIRING DIAGRAM

E133418E03

INSPECTION PROCEDURE


1. READ VALUE USING INTELLIGENT TESTER (EVAP FIN TEMP)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG) and turn the intelligent tester main switch on.

  1. Select the item below in the Data List, and read the value displayed on the intelligent tester.

    Data List / Air Conditioner: 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Evap Fin Temp
    Evaporator temperature sensor / Min.: -29.7°C (-21.46°F)
    Max.: 59.55°C (139.28°F)
    Actual evaporator temperature is displayed
    Open circuit: -29.7°C (-21.46°F)
    Short circuit: 59.55°C (139.28°F)

    OK:
    The display is as specified in the normal condition column.


    Result:
    Result
    Proceed to
    NG
    A
    OK (Checking from PROBLEM SYMPTOMS TABLE)
    B
    OK (Checking from DTC)
    C



B
PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)

C
REPLACE AIR CONDITIONING AMPLIFIER (Click here)
A


2. INSPECT NO. 1 COOLER THERMISTOR (EVAPORATOR TEMPERATURE SENSOR)

  1. Remove the No. 1 cooler thermistor from the front evaporator.E154273E01

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    -10°C (14°F)
    7.30 to 9.10 kΩ
    1 - 2
    -5°C (23°F)
    5.65 to 6.95 kΩ
    1 - 2
    0°C (32°F)
    4.40 to 5.35 kΩ
    1 - 2
    5°C (41°F)
    3.40 to 4.15 kΩ
    1 - 2
    10°C (50°F)
    2.70 to 3.25 kΩ
    1 - 2
    15°C (59°F)
    2.14 to 2.58 kΩ
    1 - 2
    20°C (68°F)
    1.71 to 2.05 kΩ
    1 - 2
    25°C (77°F)
    1.38 to 1.64 kΩ
    1 - 2
    30°C (86°F)
    1.11 to 1.32 kΩ

    NOTICE:
    1. Touching the thermistor even slightly may change the resistance value. Be sure to hold the connector of the thermistor.
    2. When measuring, the thermistor temperature must be the same as the ambient temperature.

    HINT:
    As the temperature increases, the resistance decreases (see the graph).



NG
REPLACE NO. 1 COOLER THERMISTOR
OK


3. INSPECT AIR CONDITIONING HARNESS
  1. Remove the air conditioning harness.

  1. E135297E04
    Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    z17-6 (TEA) - 2
    Always
    Below 1 Ω
    z17-5 (SGA) - x2-1
    Always
    Below 1 Ω
    z17-6 (TEA) - Body ground
    Always
    10 kΩ or higher
    z17-5 (SGA) - Body ground
    Always
    10 kΩ or higher



NG
REPLACE AIR CONDITIONING HARNESS ASSY
OK

REPLACE AIR CONDITIONING AMPLIFIER (Click here)


← B1412/12 Ambient Temperature Sensor Circuit (from Jul 2010)B1413/13 Evaporator Temperature Sensor Circuit (Aug 2008 – Jun 2010) →