2007-2013 Highlander Kluger · Service Manual HEATER & AIR CONDITIONING SYSTEM

B1451/51 Compressor Solenoid Circuit

Diagnostic trouble codes · Vehicles built Aug 2008 – Jun 2010

Versions by build date: May 2007 – Jul 2008 Aug 2008 – Jun 2010 from Jul 2010

DESCRIPTION

In this circuit, the compressor receives a refrigerant compression demand signal from the air conditioning amplifier.
Based on this signal, the compressor changes the degree of refrigerant compression.
DTC No.
DTC Detection Condition
Trouble Area
B1451/51
Open or short in solenoid of externally changeable compressor circuit
  1. Compressor and magnetic clutch
  2. Wire harness between air conditioning amplifier and compressor and pulley
  3. Air conditioning amplifier

WIRING DIAGRAM

E115016E12

INSPECTION PROCEDURE


1. READ VALUE USING INTELLIGENT TESTER (REG CTRL CURRNT)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG) and turn the intelligent tester main switch on.

  1. Select the items below in the Data List, and read the value displayed on the intelligent tester.

    Data List / Air Conditioner: 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Reg Ctrl Currnt
    Regulator control current /
    Min.: 0 A
    Max.: 0.997 A
    Value changes between 0 A and 0.997 A in accordance with compressor operation
    -

    OK:
    The display is as specified in the normal condition column.


    Result:
    Result
    Proceed to
    NG
    A
    OK (Checking from PROBLEM SYMPTOMS TABLE)
    B
    OK (Checking from DTC)
    C



B
PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)

C
REPLACE AIR CONDITIONING AMPLIFIER (Click here)
A


2. INSPECT COMPRESSOR AND MAGNETIC CLUTCH
E152688E07
  1. Disconnect the compressor and magnetic clutch connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    3 - 6
    25°C (77°F)
    10.1 to 11.1 Ω



NG
REPLACE COMPRESSOR AND MAGNETIC CLUTCH (Click here)
OK


3. CHECK HARNESS AND CONNECTOR (COMPRESSOR AND MAGNETIC CLUTCH - AIR CONDITIONING AMPLIFIER)

  1. E152689E04
    Disconnect the B44 compressor and magnetic clutch connector.

  1. Disconnect the D33 amplifier connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    B44-3 (SOL+) - D33-2 (SOL+)
    Always
    Below 1 Ω
    B44-3 (SOL+) - Body Ground
    Always
    1 MΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4. CHECK HARNESS AND CONNECTOR (COMPRESSOR AND MAGNETIC CLUTCH - BODY GROUND)

  1. E152687E07
    Disconnect the B44 compressor and magnetic clutch connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    B44-6 (SOL-) - Body Ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE AIR CONDITIONING AMPLIFIER (Click here)


← B1451/51 Compressor Solenoid Circuit (May 2007 – Jul 2008)B1451/51 Compressor Solenoid Circuit (from Jul 2010) →