PTC Heater Circuit
Circuit diagnosis · Vehicles built Aug 2008 – Jun 2010
Versions by build date: May 2007 – Jul 2008 Aug 2008 – Jun 2010 from Jul 2010
DESCRIPTION
PTC heater relays are closed in accordance with signals from the air conditioning amplifier and power is supplied to the PTC heater.WIRING DIAGRAM


INSPECTION PROCEDURE
| 1. INSPECT FUSE (PTC NO. 1, PTC NO. 2, PTC NO. 3) |
Remove the PTC NO. 1, PTC NO. 2 and PTC NO. 3 fuses from the engine room No. 2 relay block.
Measure the resistance of the fuses.
- Standard resistance:
Tester Connection
Condition
Specified Condition
PTC NO. 1
Always
Below 1 Ω
PTC NO. 2
Always
Below 1 Ω
PTC NO. 3
Always
Below 1 Ω
|
|
||||
| OK | |
| 2. INSPECT PTC HEATER RELAY |
Remove the No. 1, No. 2 and No. 3 PTC heater relays from the engine room No. 2 relay block.

Measure the resistance of the relays.
- Standard resistance:
Tester Connection
Condition
Specified Condition
3 - 5
When battery voltage is not applied to terminals 1 and 2)
10 kΩ or higher
3 - 5
When battery voltage is applied to terminals 1 and 2)
Below 1 Ω
|
|
||||
| OK | |
| 3. CHECK HARNESS AND CONNECTOR (PTC HEATER RELAY - BODY GROUND) |
Remove the No. 1, No. 2 and No. 3 PTC heater relays from the engine room No. 2 relay block.

Measure the resistance according to the value(s) in the table below.
- Standard resistance:
Tester Connection
Condition
Specified Condition
No. 1 PTC heater relay terminal 2 - Body ground
Always
Below 1 Ω
No. 2 PTC heater relay terminal 2 - Body ground
Always
Below 1 Ω
No. 3 PTC heater relay terminal 2 - Body ground
Always
Below 1 Ω
|
|
||||
| OK | |
| 4. CHECK HARNESS AND CONNECTOR (AIR CONDITIONING AMPLIFIER - PTC HEATER RELAY) |
Remove the No. 1, No. 2 and No. 3 PTC heater relays from the engine room No. 2 relay block.

Turn the ignition switch on (IG).
When the PTC heater operating conditions are met (engine at idling speed or faster, ambient temperature is 10°C (50°F) or less, engine coolant temperature is 65°C (149°F) or less, set temperature switch is set to MAX HOT), turn the blower switch to the LO setting.
Measure the voltage according to the value(s) in the table below.
- Standard voltage:
Tester Connection
Condition
Specified Condition
No. 1 PTC heater relay terminal 1 - Body ground
Always
11 to 14 V
No. 2 PTC heater relay terminal 1 - Body ground
Always
11 to 14 V
No. 3 PTC heater relay terminal 1 - Body ground
Always
11 to 14 V
|
|
||||
| OK | |
| 5. CHECK HARNESS AND CONNECTOR (BATTERY - PTC HEATER RELAY) |
Remove the No. 1, No. 2 and No. 3 PTC heater relays from the engine room No. 2 relay block.

Measure the voltage according to the value(s) in the table below.
- Standard voltage:
Tester Connection
Condition
Specified Condition
No. 1 PTC heater relay terminal 5 - Body ground
Always
11 to 14 V
No. 2 PTC heater relay terminal 5 - Body ground
Always
11 to 14 V
No. 3 PTC heater relay terminal 5 - Body ground
Always
11 to 14 V
|
|
||||
| OK | |
| 6. CHECK HARNESS AND CONNECTOR (PTC HEATER RELAY - PTC HEATER) |
Remove the No. 1, No. 2 and No. 3 PTC heater relays from the engine room No. 2 relay block.

Measure the resistance according to the value(s) in the table below.
- Standard resistance:
Tester Connection
Condition
Specified Condition
No. 1 PTC heater relay terminal 3 - D40-2 (B)
Always
Below 1 Ω
No. 2 PTC heater relay terminal 3 - D40-3 (B)
Always
Below 1 Ω
No. 3 PTC heater relay terminal 3 - D40-1 (B)
Always
Below 1 Ω
|
|
||||
| OK | |
| 7. CHECK AIR CONDITIONING AMPLIFIER |
Remove the air conditioning amplifier (Click here) with its connectors still connected.

Turn the ignition switch on (IG).
When the PTC heater operating conditions are met (engine at idling speed or faster, ambient temperature is 10°C (50°F) or less, engine coolant temperature is 65°C (149°F) or less, set temperature switch is set to MAX HOT), turn the blower switch to the Lo setting.
Measure the voltage according to the value(s) in the table below.
- Standard voltage:
Tester Connection
Condition
Specified Condition
D33-3 (PTC1) - Body ground
Always
11 to 14 V
D33-22 (PTC2) - Body ground
Always
11 to 14 V
D33-4 (PTC3) - Body ground
Always
11 to 14 V
|
|
||||
| OK | |
| 8. REPLACE PTC HEATER |
Replace the PTC heater (Click here).
| NEXT | |
| 9. CHECK PTC HEATER (OPERATION) |
Operate the PTC heater to check that it functions properly.
- OK:
- PTC heater function operates normally.
|
|
||||
| OK | ||
| ||
