2007-2013 Highlander Kluger · Service Manual HEATER & AIR CONDITIONING SYSTEM

PTC Heater Circuit

Circuit diagnosis · Vehicles built from Jul 2010

Versions by build date: May 2007 – Jul 2008 Aug 2008 – Jun 2010 from Jul 2010

DESCRIPTION

PTC heater relays are closed in accordance with signals from the air conditioning amplifier and power is supplied to the PTC heater installed on the radiator heater unit.

WIRING DIAGRAM

E127578E15

INSPECTION PROCEDURE


1. INSPECT FUSE (PTC NO. 1, PTC NO. 2, PTC NO. 3)
  1. Remove the PTC NO. 1, PTC NO. 2 and PTC NO. 3 fuses from the engine room No. 2 relay block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    PTC NO. 1
    Always
    Below 1Ω
    PTC NO. 2
    Always
    Below 1Ω
    PTC NO. 2
    Always
    Below 1Ω



NG
REPLACE FUSE
OK


2. INSPECT PTC HEATER RELAY

  1. A092673E24
    Remove the PTC HTR1, PTC HTR2 and PTC HTR3 relays from the engine room No. 2 relay block.

  1. Measure the resistance of the relays.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    3 - 5
    when battery voltage is not applied to terminals 1 and 2
    10 kΩ or higher
    3 - 5
    when battery voltage is applied to terminals 1 and 2
    Below 1 Ω



NG
REPLACE PTC HEATER RELAY
OK


3. CHECK HARNESS AND CONNECTOR (PTC HEATER RELAY - BODY GROUND)

  1. E153678E17
    Remove the PTC HTR1, PTC HTR2 and PTC HTR3 relays from the engine room No. 2 relay block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    PTC HTR1 heater relay terminal 2 - Body ground
    Always
    Below 1 Ω
    PTC HTR2 heater relay terminal 2 - Body ground
    Always
    Below 1 Ω
    PTC HTR3 heater relay terminal 2 - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4. CHECK HARNESS AND CONNECTOR (AIR CONDITIONING AMPLIFIER - PTC HEATER RELAY)

  1. E153678E18
    Remove the PTC HTR1, PTC HTR2 and PTC HTR3 relays from the engine room No. 2 relay block.

  1. Turn the ignition switch on (IG).

  1. When the PTC heater operating conditions are met (engine at idling speed or faster, ambient temperature is 10°C (50°F) or less, engine coolant temperature is 65°C (149°F) or less, set temperature switch is set to MAX HOT), turn the blower switch to the Lo setting.

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    PTC HTR1 heater relay terminal 1 - Body ground
    Always
    11 to 14 V
    PTC HTR2 heater relay terminal 1 - Body ground
    Always
    11 to 14 V
    PTC HTR3 heater relay terminal 1 - Body ground
    Always
    11 to 14 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5. CHECK HARNESS AND CONNECTOR (BATTERY - PTC HEATER RELAY)

  1. E153678E19
    Remove the PTC HTR1, PTC HTR2 and PTC HTR3 relays from the engine room No. 2 relay block.

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    PTC HTR1 heater relay terminal 5 - Body ground
    Always
    11 to 14 V
    PTC HTR2 heater relay terminal 5 - Body ground
    Always
    11 to 14 V
    PTC HTR3 heater relay terminal 5 - Body ground
    Always
    11 to 14 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6. CHECK HARNESS AND CONNECTOR (PTC HEATER RELAY - PTC HEATER)

  1. E216666E02
    Remove the PTC HTR1, PTC HTR2 and PTC HTR3 relays from the engine room No. 2 relay block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    PTC HTR1 heater relay terminal 3 - D40-2 (B)
    Always
    Below 1 Ω
    PTC HTR2 heater relay terminal 3 - D40-3 (B)
    Always
    Below 1 Ω
    PTC HTR3 heater relay terminal 3 - D40-1 (B)
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


7. CHECK AIR CONDITIONING AMPLIFIER

  1. E127567E21
    Remove the air conditioning amplifier with its connectors still connected.

  1. Turn the ignition switch on (IG).

  1. When the PTC heater operating conditions are met (engine at idling speed or faster, ambient temperature is 10°C (50°F) or less, engine coolant temperature is 65°C (149°F) or less, set temperature switch is set to MAX HOT), turn the blower switch to the Lo setting.

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    D33-3 (PTC1) - Body ground
    Always
    11 to 14 V
    D33-22 (PTC2) - Body ground
    Always
    11 to 14 V
    D33-4 (PTC3) - Body ground
    Always
    11 to 14 V



NG
REPLACE AIR CONDITIONING AMPLIFIER
OK


8. REPLACE PTC HEATER
  1. Replace the PTC heater (Click here)


NEXT


9. CHECK PTC HEATER (OPERATION)
  1. Operate the PTC heater to check that functions properly.

    OK:
    PTC heater function operates normally.



NG
PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)
OK

END (PTC HEATER IS DEFECTIVE)


← PTC Heater Circuit (Aug 2008 – Jun 2010)Rear Blower Motor Circuit (May 2007 – Jul 2008) →