2007-2013 Highlander Kluger · Service Manual HEATER & AIR CONDITIONING SYSTEM

SYSTEM DESCRIPTION

Troubleshooting · Vehicles built from Jul 2010

Versions by build date: May 2007 – Jun 2010 from Jul 2010


GENERAL
  1. The air conditioning system has the following features:

    1. An automatic, dual-control air conditioner system comprising front/rear independent temperature control is used.
    2. In accordance with the temperature set using the temperature control switch, the air conditioning amplifier determines the outlet temperature based on the input signals from various sensors. In addition, corrections are made in accordance with the signals from the water temperature sensor to control the outlet air temperature.
    3. Controls the blower motor in accordance with the airflow volume determined by the air conditioning amplifier based on the input signals from various sensors.
    4. Automatically changes the outlets in accordance with the outlet mode ratio that is determined by the air conditioning amplifier based on the input signals from various sensors.
    5. Based on the signals from the ambient temperature sensor, this system calculates the outside temperature and indicates it in the multi-information display.
    6. The left/right independent temperature control and neural network control make air conditioner control available to suit the persons in the driver seat and in the passenger seat.
    7. The Positive Temperature Coefficient (PTC) heater system contains a PTC heater that heats the air that has passed through the heater core to ensure the proper heater performance.
    8. Turns the rear defogger and outside rear mirror heaters on for 15 minutes when the rear defogger switch is pressed. Turns them off if the switch is pressed while they are operating.
    9. Checks the sensors in accordance with the operation of the air conditioner switches.
    10. The air conditioning amplifier has the function of controlling the indicator lighting.
    11. When a high load is applied to the EPS system, the EPS ECU will send a signal to the air conditioning amplifier. After receiving the signal, the air conditioning amplifier may turn off the rear defogger, front deicer, and seat heaters.


MODE POSITION AND DAMPER OPERATION
E152627E03
Control Damper
Control Position
Damper Position
Operation
Air Inlet Control Damper
FRESH
A
Brings in fresh air
RECIRC
B
Recirculates internal air
Air Mix Control Damper
(Left/Right Independent Control)
Driver and Front Passenger Side
MAX COOL to MAX HOT
(TEMP. SETTING 18 to 32°C (65 to 85°F))
C, D, E
Varies mixture ratio of fresh air and recirculation air in order to regulate temperature continuously from HOT to COOL
Mode Control Film Damper
Driver and Front Passenger Side
E106656
FACE
I, J, L, O, U
Air blows out of center registers and side registers.
E106657
BI-LEVEL
I, M, Q, R, T
Air mainly blows out of center registers, side registers, and footwell register ducts.
E106658
FOOT
H, K, N, P, S
Air mainly blows out of front and rear footwell register ducts.
In addition, air blows out slightly from front and side defrosters, and side registers.
E106659
FOOT/DEF
G, K, N, P, S
Air mainly blows out of front and side defrosters to defrost windshield. Air also blows out from front and rear footwell register ducts, and side registers.
E106660
DEF
F, K, N, U, V
Air blows out of front and side defrosters and side registers to defrost windshield.
E152628E01
Control Damper
Control Position
Damper Position
Operation
Air Mix Control Damper
MAX COOL to MAX HOT TEMP. SETTING 18 to 32°C (65 to 90°F)
D, E
Varies mixture ratio of fresh air and recirculating air in order to regulate temperature continuously from HOT to COOL
Mode Control Film Damper
E106656
FACE
A
Air blows out of roof face ducts.
E106657
BI-LEVEL
B
Air blows out of roof face ducts and rear foot ducts.
E106658
FOOT
C
Air blows out of rear foot ducts.

AIR OUTLET AND AIRFLOW VOLUME
E153099E01
Air Outlet Mode
Air Outlet Position Symbol
A
B
C
D
E
Center Face
Side Face
Foot
Footwell
Defroster
E106656
FACE
E107019
E107019
X
X
X
E106657
BI-LEVEL
E107021
E107021
E107020
E107021
X
E106658
FOOT
X
E107317
E107020
E107020
E107317
E106659
FOOT/DEF
X
E107317
E107021
E107021
E107021
E106660
DEF
X
E107021
X
X
E107019

HINT:
The size of the circle ○ indicates the proportion of airflow volume.

E152630E01
Air Outlet Mode
Air Outlet Position Symbol
A
B
Side Face
Rear Foot
E106656
FACE
E107019
X
E106657
BI-LEVEL
E107021
E107021
E106658
FOOT
X
E107019

HINT:
The size of the circle ○ indicates the proportion of airflow volume.


A/C FLOW SENSOR
The A/C flow sensor, which is mounted on the compressor with pulley, is used to detect the amount of refrigerant flow. The A/C flow sensor converts the amount of refrigerant flow that is detected to a voltage value to send it to the A/C amplifier. The voltage value sent from the A/C flow sensor changes depending on the amount of refrigerant flow. As the amount of refrigerant flow becomes larger, the voltage becomes lower. As the amount of refrigerant flow becomes smaller, the voltage becomes higher. The A/C amplifier supplies 5 V to the A/C flow sensor and monitors change in the voltage value sent from the A/C flow sensor. The A/C amplifier then sends a signal to the ECM via CAN communication to allow the ECM to control the engine speed while the air conditioning is on.
← SYSTEM DESCRIPTION (May 2007 – Jun 2010)HOW TO PROCEED WITH TROUBLESHOOTING (May 2007 – Jul 2008) →