2007-2013 Highlander Kluger · Service Manual HEATER & AIR CONDITIONING SYSTEM

DATA LIST / ACTIVE TEST

System information · Vehicles built May 2007 – Jun 2010

Versions by build date: May 2007 – Jun 2010 from Jul 2010


READ DATA LIST

HINT:
Using the intelligent tester to read the Data List allows the values or states of switches, sensors, actuators, and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

  1. Connect the intelligent tester to the DLC3.

  2. Turn the ignition switch on (IG) and turn the intelligent tester on.

  3. Read the Data List by following the prompts on the tester.

    Data List / Air Conditioner: 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Ambi Temp Sens
    Ambient temperature sensor /
    Min.: -23.3°C (-9.94°F)
    Max.: 65.95°C (150.71°F)
    Actual ambient temperature is displayed
    -
    Coolant Temp
    Engine coolant temperature sensor /
    Min.: 1.3°C (34.34°F)
    Max.: 90.55°C (194.99°F)
    Actual engine coolant temperature is displayed
    -
    Blower Level
    Blower motor speed level /
    Min.: 0, Max.: 31
    Increases in range between 0 and 31 as blower motor speed increases
    -
    Air Mix Pulse-P
    Passenger side air mix servo motor target pulse /
    Min.: 0, Max.: 255
    1. LHD:
      MAX COLD: 105 (pulse)
      MAX HOT: 7 (pulse)
    1. RHD:
      MAX COLD: 5 (pulse)
      MAX HOT: 103 (pulse)
    -
    Air Out Pulse-D
    Driver side air outlet servo motor target /
    Min.: 0, Max.: 255
    FACE: 8 (pulse)
    B/L: 30 (pulse)
    FOOT: 67 (pulse)
    FOOT/DEF: 80 (pulse)
    DEF: 97 (pulse)
    -
    A/I Damp Targ Pls
    Air inlet damper target pulse /
    Min.: 0, Max.: 255
    RECIRCULATION: 7 (pulse)
    FRESH: 28 (pulse)
    -
    Evap Fin Temp
    Evaporator temperature sensor /
    Min.: -29.7°C (-21.46°F)
    Max.: 59.55°C (139.19°F)
    Actual evaporator temperature is displayed
    -
    Reg Press Sens
    Regulator pressure sensor /
    Min.: 0 kgf/cm2G
    Max.: 38.25 kgf/cm2G
    Actual regulator pressure is displayed
    -
    Reg Ctrl Currnt
    Regulator control current /
    Min.: 0 A
    Max.: 0.997 A
    Value changes between 0 A and 0.997 A in accordance with compressor and magnetic clutch operation
    -
    Blower Level-R
    Rear blower motor speed level /
    Min.: 0, Max.: 31
    Increases in range between 0 and 31 as rear blower motor speed increases
    -
    Air Out Pulse-R
    Rear side air outlet control servo motor target pulse /
    Min.: 0, Max.: 255
    Rr FACE: 83 (pulse)
    Rr B/L: 38 (pulse)
    FOOT: 7 (pulse)
    -
    Air Mix Pulse-R
    Rear side air mix control servo motor target pulse /
    Min.: 0, Max.: 255
    1. LHD:
      MAX COLD: 9 (pulse)
      MAX HOT: 54 (pulse)
    1. RHD:
      MAX COLD: 9 (pulse)
      MAX HOT: 54 (pulse)
    -
    R-Evap Temp Sen
    Rear Evaporator temperature sensor /
    Min.: -29.7°C (-21.46°F)
    Max.: 59.55°C (139.19°F)
    Actual evaporator temperature is displayed
    -
    #Codes
    Number of trouble codes /
    Min.: 0, Max.: 255
    Number of DTCs displayed
    -


PERFORM ACTIVE TEST

HINT:
Using the intelligent tester to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.

  1. Connect the intelligent tester to the DLC3.

  2. Turn the ignition switch on (IG) and turn the intelligent tester on.

  3. Perform the Active Test by following the prompts on the tester.

    Active Test / Air Conditioner: 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Blower Motor
    Blower motor
    Min.: 0, Max.: 31
    -
    A/C Mag Clutch
    Magnetic clutch relay
    OFF, ON
    -
    Defogger Rly-R
    Defogger relay (Rear)
    OFF, ON
    -
    Electric Heater1
    PTC heater 1
    OFF, ON
    -
    Electric Heater2
    PTC heater 2
    OFF, ON
    -
    Electric Heater3
    PTC heater 3
    OFF, ON
    -
    Air Mix Pulse-P
    Air mix servo motor pulse (P side)
    1. LHD:
      Min.: 5, Max.: 103
    1. RHD:
      Min.: 7, Max.: 105
    -
    Air Out Pulse-D
    Air outlet servo motor pulse (D side)
    Min.: 8, Max.: 97
    -
    A/I Damp Targ Pls
    Air inlet damper target pulse
    Min.: 7, Max.: 28
    -
    R Blower Motor
    Rear blowerr motor
    Min.: 0, Max.: 31
    -
    R Air Mix Pulse
    Rear air mix control servo motor pulse
    1. LHD:
      Min.: 9, Max.: 54
    1. RHD:
      Min.: 9, Max.: 54
    -

← DTC CHECK / CLEAR (from May 2007)DATA LIST / ACTIVE TEST (from Jul 2010) →