2007-2013 Highlander Kluger · Service Manual HEATER & AIR CONDITIONING SYSTEM

DATA LIST / ACTIVE TEST

System information · Vehicles built from Jul 2010

Versions by build date: May 2007 – Jun 2010 from Jul 2010


READ DATA LIST

HINT:
Using the intelligent tester to read the Data List allows the values or states of switches, sensors, actuators, and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

  1. Connect the intelligent tester to the DLC3.

  2. Turn the ignition switch on (IG) and turn the intelligent tester on.

  3. Read the Data List by following the prompts on the tester.

    Air Conditioner: 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Room Temperature sensor
    (Room Temp)
    Room temperature sensor /
    Min.: -6.5°C (20.3°F)
    Max.: 57.25°C (135.05°F)
    Actual cabin temperature is displayed
    -
    Ambient Temp Sensor
    (Ambi Temp Sens)
    Ambient temperature sensor /
    Min.: -23.3°C (-9.94°F)
    Max.: 65.94°C (150.71°F)
    Actual ambient temperature is displayed
    -
    Adjusted Ambient Temp
    (Ambi Temp)
    Adjusted ambient temperature /
    Min.: -30.8°C (-23.44°F)
    Max.: 50.8°C (123.44°F)
    -
    -
    Solar Sensor (D side)
    (Solar Sens-D)
    Driver side solar sensor /
    Min.: 0, Max.: 255
    Driver side solar sensor value increases as brightness increases
    -
    Solar Sensor (P side)
    (Solar Sens-P)
    Passenger side solar sensor /
    Min.: 0, Max.: 255
    Front passenger side solar sensor value increases as brightness increases
    -
    Engine Coolant Temp
    (Coolant Temp)
    Engine coolant temperature sensor /
    Min.: 1.3°C (34.34°F)
    Max.: 90.55°C (194.99°F)
    Actual engine coolant temperature is displayed
    -
    Set Temperature (D side)
    (Set Temp-D)
    Driver side set temperature /
    Min.: 0°C (32°F)
    Max.: 30°C (86°F)
    Driver side actual set temperature is displayed
    -
    Set Temperature (P side)
    (Set Temp-P)
    Passenger side set temperature /
    Min.: 0°C (32°F)
    Max.: 30°C (86°F)
    Front passenger side actual set temperature is displayed
    -
    Blower Motor Speed Level
    (Blower Level)
    Blower motor speed level /
    Min.: 0, Max.: 31
    Increases in range between 0 and 31 as blower motor speed increases
    -
    Air Mix Servo Targ Pulse (D)
    (Air Mix Pulse-D)
    Driver side air mix control servo motor target pulse /
    Min.: 0, Max.: 255
    1. LHD:
      MAX COLD: 5 (pulse)
      MAX HOT: 103 (pulse)
    1. RHD:
      MAX COLD: 105 (pulse)
      MAX HOT: 7 (pulse)
    -
    Air Mix Servo Targ Pulse (P)
    (Air Mix Pulse-P)
    Passenger side air mix control servo motor target pulse /
    Min.: 0, Max.: 255
    1. LHD:
      MAX COLD: 105 (pulse)
      MAX HOT: 7 (pulse)
    1. RHD:
      MAX COLD: 5 (pulse)
      MAX HOT: 103 (pulse)
    -
    Air Outlet Servo Pulse (D)
    (Air Out Pulse-D)
    Driver side air outlet control servo motor target /
    Min.: 0, Max.: 255
    FACE: 8 (pulse)
    B/L: 30 (pulse)
    FOOT: 67 (pulse)
    FOOT/DEF: 80 (pulse)
    DEF: 97 (pulse)
    -
    Air Inlet Damper Targ Pulse
    (A/I Damp Targ Pls)
    Air inlet damper target pulse /
    Min.: 0, Max.: 255
    RECIRCULATION: 7 (pulse)
    FRESH: 28 (pulse)
    -
    Evaporator Fin Thermistor
    (Evap Fin Temp)
    Evaporator temperature sensor /
    Min.: -29.7°C (-21.46°F)
    Max.: 59.55°C (139.19°F)
    Actual evaporator temperature is displayed
    -
    Evaporator Target Temp
    (Evap Tag Temp)
    Evaporator target temperature /
    Min.: -327.68°C (-557.82°F)
    Max.: 327.68°C (621.81°F)
    Evaporator target temperature displayed
    -
    Regulator Pressure Sensor
    (Reg Press Sens)
    Regulator pressure sensor /
    Min.:-0.45668 MPaG
    Max.: 3.29437 MPaG
    Actual regulator pressure is displayed
    -
    Regulator Control Current
    (Reg Ctrl Currnt)
    Regulator control current /
    Min.: 0 A
    Max.: 0.997 A
    Value changes between 0 A and 0.997 A in accordance with compressor operation
    -
    Room Temp Sensor (Rear)
    (Rear Room Temp)
    Rear room temperature sensor /
    Min.: -6.5°C (20.3°F)
    Max.: 57.25°C (135.05°F)
    Actual rear cabin temperature is displayed
    -
    Set Temperature (Rear)
    (Set Temp Rear)
    Rear set temperature /
    Min.: 0
    Max.: 255
    Actual rear set temperature is displayed
    -
    Blower Motor Level (Rear)
    (Blower Level-R)
    Rear blower motor speed level /
    Min.; 0, Max.: 31
    Increases in range between 0 and 31 as rear blower motor speed increases
    -
    Air Outlet Servo Pulse (R)
    (Air Out Pulse-R)
    Rear air outlet control servo motor target pulse /
    Min.: 0, Max.: 255
    Rr FACE: 83 (pulse)
    Rr B/L: 38 (pulse)
    Rr FOOT: 7 (pulse)
    -
    Air Mix Servo Targ Pulse (R)
    (Air Mix Pulse-R)
    Rear air mix control servo motor target pulse /
    Min.: 0, Max.: 255
    1. LHD:
      MAX COLD: 9 (pulse)
      MAX HOT: 54 (pulse)
    1. RHD:
      MAX COLD: 9 (pulse)
      MAX HOT: 54 (pulse)
    -
    Ambient Temp Sens (Rear)
    (R-Ambi Temp Sen)
    Rear Evaporator temperature sensor /
    Min.: -29.7°C (-21.46°F)
    Max.: 59.55°C (139.19°F)
    Actual evaporator temperature is displayed
    -
    Flow Sensor
    (Flow Sens)
    A/C flow sensor / Min.: 0V, Max.: 5 V
    Ignition switch on (IG): 0.3 to 4.7 V
    A/C flow sensor is malfunctioning when a constant value below 0.3 V or higher than 4.7 V is displayed continuously for more than 4 seconds.
    A/C Cutoff Signal
    (A/C Cutoff)
    A/C control cutoff signal /
    OFF or ON
    A/C switch on: OFF
    A/C switch off: ON
    -
    Number of Trouble Codes
    (#Codes)
    Number of trouble codes /
    Min.: 0, Max.: 255
    Number of DTCs displayed
    -


PERFORM ACTIVE TEST

HINT:
Using the intelligent tester to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.

  1. Connect the intelligent tester to the DLC3.

  2. Turn the ignition switch on (IG) and turn the intelligent tester on.

  3. Perform the Active Test by following the prompts on the tester.

    Air Conditioner: 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Blower Motor
    Blower motor
    Min.: 0, Max.: 31
    -
    Magnetic Clutch Relay
    Magnetic clutch relay
    OFF, ON
    -
    Defogger Relay (Rear)
    Defogger relay (Rear)
    OFF, ON
    -
    Mirror Heater Relay
    Mirror Heater
    OFF, ON
    -
    Deicer Relay (Front)
    Front window deicer
    OFF, ON
    -
    Heater Active Level
    Heater active level
    Min.: 0, Max.: 3
    -
    Air Mix Servo Targ Pulse (D)
    Air mix servo motor pulse (D side)
    1. LHD:
      Min.: 5, Max.: 103
    1. RHD:
      Min.: 7, Max.: 105
    -
    Air Mix Servo Targ Pulse (P)
    Air mix servo motor pulse (P side)
    1. LHD:
      Min.: 7, Max.: 105
    1. RHD:
      Min.: 5, Max.: 103
    -
    Air Outlet Servo Targ Pulse (D)
    Air outlet servo motor pulse (D side)
    Min.: 8, Max.: 97
    -
    Air Inlet Damper Targ Pulse
    Air inlet damper target pulse
    Min.: 7, Max.: 28
    -
    Rear Blower Motor
    Rear blower motor
    Min.: 0, Max.: 31
    -
    Rear Air Mix Servo Targ Pulse
    Rear air mix control servo motor pulse
    Min.: 9, Max.: 54
    -

← DATA LIST / ACTIVE TEST (May 2007 – Jun 2010)DIAGNOSTIC TROUBLE CODE CHART (May 2007 – Jul 2008) →