2007-2013 Highlander Kluger · Service Manual HEATER & AIR CONDITIONING SYSTEM

INSTALLATION

Removal / installation · Vehicles built Aug 2008 – Jun 2010

Versions by build date: May 2007 – Jul 2008 Aug 2008 – Jun 2010 Jul 2010 – Jul 2013 from Aug 2013


1. INSTALL AIR CONDITIONING UNIT

  1. Install the air conditioning unit with the 3 bolts.

    E151012E01

    Torque:
    9.8 N*m{ 100 kgf*cm , 87 in.*lbf }

    NOTICE:
    Tighten the bolts in the order shown in the illustration to install the air conditioning unit assembly.


2. INSTALL INSTRUMENT PANEL REINFORCEMENT ASSEMBLY WITH AIR CONDITIONING UNIT (w/o PTC Heater)
  1. Driver Side:

    1. Using a "TORX" socket wrench (T40), install the instrument panel reinforcement assembly with the 3 "TORX" bolts.

      Torque:
      17 N*m{ 173 kgf*cm , 13 ft.*lbf }

  1. Passenger Side:

    1. Using a 12 mm hexagon wrench, adjust the position of the 2 collars.

      Torque:
      6.0 N*m{ 61 kgf*cm , 53 in.*lbf }

    2. Using a "TORX" socket wrench (T40), install the instrument panel reinforcement assembly with the 2 "TORX" bolts.

      Torque:
      20 N*m{ 204 kgf*cm , 15 ft.*lbf }


      E151009E01

  1. Install the 2 bolts and 2 caps to the engine compartment side.

    Torque:
    20 N*m{ 204 kgf*cm , 15 ft.*lbf }

  1. Install the instrument panel reinforcement assembly with air conditioning unit with the nut.

    Torque:
    9.8 N*m{ 100 kgf*cm , 87 in.*lbf }

  1. Engage the cooler drain hose.

    E151007

  1. Connect the blower motor connector.

  1. Install the 2 nuts and bolt.

  1. Connect each connector.

  1. Connect the 2 earth wires with the 2 bolts <A>.

    Torque:
    8.4 N*m{ 86 kgf*cm , 74 in.*lbf }

  1. Engage each clamp.

    E151006E01


3. INSTALL INSTRUMENT PANEL REINFORCEMENT ASSEMBLY WITH AIR CONDITIONING UNIT (w/ PTC Heater)
  1. Driver Side:

    1. Using a "TORX" socket wrench (T40), install the instrument panel reinforcement assembly with the 3 "TORX" bolts.

      Torque:
      17 N*m{ 173 kgf*cm , 13 ft.*lbf }

  1. Passenger Side:

    1. Using a 12 mm hexagon wrench, adjust the position of the 2 collars.

      Torque:
      6.0 N*m{ 61 kgf*cm , 53 in.*lbf }

    2. Using a "TORX" socket wrench (T40), install the instrument panel reinforcement assembly with the 2 "TORX" bolts.

      Torque:
      20 N*m{ 204 kgf*cm , 15 ft.*lbf }


      E151009E01

  1. Install the 2 bolts and 2 caps to the engine compartment side.

    Torque:
    20 N*m{ 204 kgf*cm , 15 ft.*lbf }

  1. Install the instrument panel reinforcement assembly with air conditioning unit with the nut.

    Torque:
    9.8 N*m{ 100 kgf*cm , 87 in.*lbf }

  1. Engage the cooler drain hose.

    E151007

  1. Connect the 2 quick heater connectors.

  1. Connect the blower motor connector.

  1. Install the 2 nuts and bolt.

  1. Connect each connector.

  1. Connect the 2 earth wires with the 2 bolts <A>.

    Torque:
    8.4 N*m{ 86 kgf*cm , 74 in.*lbf }

  1. Engage each clamp.

    E151005E01


4. INSTALL NO. 1 INSTRUMENT PANEL BRACE SUB-ASSEMBLY

  1. E151002
    Install the 3 nuts.

  1. Install the 2 bolts.

  1. Install the No. 1 instrument panel brace sub-assembly with the screw.

    Torque:
    9.8 N*m{ 100 kgf*cm , 87 in.*lbf }

  1. E151001
    Engage each clamp.

  1. Connect the earth wire with the bolt.

    Torque:
    8.4 N*m{ 86 kgf*cm , 74 in.*lbf }


5. INSTALL NO. 2 INSTRUMENT PANEL BRACE SUB-ASSEMBLY

  1. E151004
    Install the 3 nuts.

  1. Install the bolt.

  1. Install the No. 2 instrument panel brace sub-assembly with the screw.

    Torque:
    9.8 N*m{ 100 kgf*cm , 87 in.*lbf }

  1. E151003
    Engage each clamp.

  1. Connect the earth wire with the bolt.

    Torque:
    8.4 N*m{ 86 kgf*cm , 74 in.*lbf }


6. INSTALL CENTER HEATER TO REGISTER DUCT

  1. E150999
    Engage the 4 claws and install the center heater to register duct.

  1. Engage the clamp.


7. INSTALL NO. 1 CONSOLE BOX DUCT (w/o Rear Air Conditioning System)

  1. E151000
    Install the clip and the No. 1 console box duct.


8. INSTALL REAR NO. 3 AIR DUCT

  1. E150998
    Engage the 2 claws and install the rear No. 3 air duct.

  1. Install the clip.

  1. E151083E01
    Engage the claw and install the floor carpet.


9. INSTALL REAR NO. 1 AIR DUCT

  1. E150997
    Engage the 2 claws and install the rear No. 1 air duct.

  1. Install the clip.

  1. Engage the clamp.

  1. E151082E01
    Engage the claw and install the floor carpet.


10. INSTALL AIR CONDITIONING AMPLIFIER ASSEMBLY

  1. E150334
    Install the air conditioning amplifier assembly with the 2 screws.

  1. Connect each connector.


11. INSTALL ECM (for RHD)

  1. A171720E01
    Install the 2 nuts, bolt and ECM.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

  1. Install the wire harness clamp.

  1. Connect the 5 ECM connectors.

  1. Connect the harness connector (LHD).


12. INSTALL POWER STEERING ECU ASSEMBLY (for LHD)

  1. C166319
    Install the power steering ECU assembly with the 3 nuts.

    Torque:
    14 N*m{ 143 kgf*cm , 10 ft.*lbf }

  1. C167533E01
    Check that the connector lever is at the fully unlocked position before installation.

    NOTICE:
    If the lever has been lifted out of the fully unlocked position, it may cause a faulty connection.

  1. C165548E01
    Connect the 4 connectors to the power steering ECU assembly.

  1. Lightly pull on the connector and check that the connector does not disconnect.


13. INSTALL POWER STEERING ECU ASSEMBLY (for RHD)

  1. C166320
    Install the power steering ECU assembly with the 3 nuts.

    Torque:
    14 N*m{ 143 kgf*cm , 10 ft.*lbf }

  1. C167534E01
    Check that the connector lever is at the fully unlocked position before installation.

    NOTICE:
    If the lever has been lifted out of the fully unlocked position, it may cause a faulty connection.

  1. C165551E01
    Connect the 4 connectors to the power steering ECU assembly.

  1. Lightly pull on the connector and check that the connector will not be disconnected.

  1. Install the wire harness clamp to the power steering ECU assembly.


14. CONNECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

  1. E151587
    Connect the instrument panel junction block assembly with the 3 nuts.

    Torque:
    8.4 N*m{ 86 kgf*cm , 74 in.*lbf }


15. INSTALL STEERING COLUMN ASSEMBLY (for LHD)

  1. C166135E01
    Check that the 2 bushings are securely installed to the steering column assembly.

    HINT:
    If the bushings are missing or damaged, replace the steering column assembly with a new one.

  1. C166130
    Install the steering column assembly with the bolt and 2 nuts.

    Torque:
    Bolt:
    36 N*m{ 367 kgf*cm , 27 ft.*lbf }
    Nut:
    25 N*m{ 255 kgf*cm , 18 ft.*lbf }

    NOTICE:
    There are two different bolt sizes (12 mm (0.472 in.) or 14 mm (0.551 in.)) available.

  1. Connect the connectors and engage the wire harness clamps to the steering column assembly.

  1. C166140
    Connect the connector to the power steering ECU assembly.

  1. C166139
    Connect the connector to the power steering ECU assembly.

    HINT:
    As shown in the illustration, securely return the lock lever to its original position to connect the connector.


16. INSTALL STEERING COLUMN ASSEMBLY (for RHD)

  1. C166135E01
    Check that the 2 bushings are securely installed to the steering column assembly.

    HINT:
    If the bushings are missing or damaged, replace the steering column assembly with a new one.

  1. C168095
    Install the steering column assembly with the bolt and 2 nuts.

    Torque:
    Bolt:
    36 N*m{ 367 kgf*cm , 27 ft.*lbf }
    Nut:
    25 N*m{ 255 kgf*cm , 18 ft.*lbf }

    NOTICE:
    There are two different bolt sizes (12 mm (0.472 in.) or 14 mm (0.551 in.)) available.

  1. Connect the connectors and engage the wire harness clamps to the steering column assembly.

  1. C166143
    Connect the connector to the power steering ECU assembly.

  1. C166141
    Connect the connector to the power steering ECU assembly.

    HINT:
    As shown in the illustration, securely return the lock lever to its original position to connect the connector.


17. CONNECT STEERING INTERMEDIATE SHAFT SUB-ASSEMBLY

  1. C165545E01
    Align the matchmarks on the steering intermediate shaft sub-assembly and the power steering link assembly.

  1. C165544
    Install a new bolt.

    Torque:
    35 N*m{ 360 kgf*cm , 26 ft.*lbf }

  1. C166146
    Install the steering intermediate shaft sub-assembly to the steering column hole shield.

  1. C166145
    Tighten the bolt.


18. INSTALL NO. 1 AIR DUCT SUB-ASSEMBLY (for LHD)

  1. C166133
    Engage the 2 claws to install the No. 1 air duct sub-assembly.


19. INSTALL NO. 1 AIR DUCT SUB-ASSEMBLY (for RHD)

  1. C166134
    Engage the 2 claws to install the No. 1 air duct sub-assembly.


20. INSTALL DRIVER SIDE KNEE AIRBAG ASSEMBLY
  1. Check that the ignition switch is off.

  1. Check that the battery negative (-) cable is disconnected.

    CAUTION:
    Wait for at least 90 seconds after disconnecting the cable to prevent airbag deployment.

  1. C165102
    Install the DLC3 to the driver side knee airbag assembly with the 2 claws.

  1. C168061
    Connect the connector to the driver side knee airbag assembly.

    NOTICE:
    When handling the airbag connector, take care not to damage the airbag wire harness.

  1. C168059
    Support the driver side knee airbag assembly with one hand as shown in the illustration.

  1. C165099
    Temporarily install the driver side knee airbag assembly with the 2 hooks.

  1. C165098
    Install the driver side knee airbag assembly with the 4 bolts.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }


21. INSTALL BRAKE PEDAL SUPPORT SUB-ASSEMBLY (for LHD)

  1. C165374
    Install the brake pedal support sub-assembly with the 4 nuts.

    Torque:
    13 N*m{ 132 kgf*cm , 10 ft.*lbf }

  1. C165373
    Install the brake pedal support sub-assembly to the instrument panel reinforcement with the 2 bolts.

    Torque:
    35 N*m{ 357 kgf*cm , 26 ft.*lbf }

  1. C165371
    Connect the brake pedal load sensing switch connector and engage the clamp.


22. INSTALL BRAKE PEDAL SUPPORT SUB-ASSEMBLY (for RHD)

  1. C165376
    Install the brake pedal support sub-assembly with the 4 nuts.

    Torque:
    13 N*m{ 132 kgf*cm , 10 ft.*lbf }

  1. C165375
    Install the brake pedal support sub-assembly to the instrument panel reinforcement with the 2 bolts.

    Torque:
    35 N*m{ 357 kgf*cm , 26 ft.*lbf }

  1. C165372
    Connect the brake pedal load sensing switch connector and engage the clamp.


23. CONNECT BRAKE MASTER CYLINDER PUSH ROD CLEVIS

  1. C166415E01
    Apply lithium soap base glycol grease to the push rod pin.

  1. Connect the brake master cylinder push rod clevis to the brake pedal with the push rod pin, and install a new clip as shown in the illustration.


24. INSTALL BRAKE PEDAL RETURN SPRING

  1. C165369
    Install the brake pedal return spring between the instrument panel reinforcement and brake master cylinder push rod clevis.


25. INSTALL STOP LIGHT SWITCH ASSEMBLY

  1. E150075E01
    Temporarily install the stop light switch assembly with the stop light switch lock nut.

  1. E150611E01
    Turn the stop light switch assembly so that the clearance between the nut end and stop light switch cushion is between 0.5 to 2.4 mm (0.020 to 0.095 in.).

  1. Tighten the stop light switch lock nut.

    Torque:
    17 N*m{ 173 kgf*cm , 12 ft.*lbf }

  1. E150073
    Connect the connector.


26. INSTALL INSTRUMENT PANEL SAFETY PAD ASSEMBLY (for Pole Antenna Type)
  1. Engage the 5 claws.

    NOTICE:
    Do not allow the wire harness to get caught in the claws.

  1. Install the 2 bolts <D> and nut <H>.

  1. Install the 2 clips.

    B168377E01

  1. Engage each clamp.

  1. Install the 2 passenger airbag bolts <A>.

    Torque:
    20 N*m{ 204 kgf*cm , 15 ft.*lbf }

  1. Install the bolt <E>.

  1. Connect each connector and install the instrument panel safety pad assembly.

    B173015E01


27. INSTALL INSTRUMENT PANEL SAFETY PAD ASSEMBLY (for Glass Antenna Type)
  1. Engage the 5 claws.

    NOTICE:
    Do not allow the wire harness to get caught in the claws.

  1. Install the 2 bolts <D> and nut <H>.

  1. Install the 2 clips.

    B168377E01

  1. Engage each clamp.

  1. Install the 2 passenger airbag bolts <A>.

    Torque:
    20 N*m{ 204 kgf*cm , 15 ft.*lbf }

  1. Connect each connector and install the instrument panel safety pad assembly.

    B168376E01


28. CONNECT INSTRUMENT PANEL WIRE ASSEMBLY
  1. Check that the ignition switch is off.

  1. Check that the battery negative (-) terminal is disconnected.

    CAUTION:
    Wait for at least 90 seconds after disconnecting the cable to prevent airbag deployment.

  1. C165103
    Connect the connector.


29. INSTALL FRONT NO. 2 SPEAKER ASSEMBLY (for LH Side)

  1. E150560
    Connect the connector.

  1. Install the front No. 2 speaker assembly with the 2 bolts.


30. INSTALL NO. 1 INSTRUMENT PANEL SPEAKER PANEL SUB-ASSEMBLY

  1. B168375
    Engage the 2 guides.

  1. Engage the 2 claws and 2 clips, and install the No. 1 instrument panel speaker panel sub-assembly.


31. INSTALL FRONT NO. 2 SPEAKER ASSEMBLY (for RH Side)

HINT:
Use the same procedures for the RH side and the LH side.


32. INSTALL NO. 2 INSTRUMENT PANEL SPEAKER PANEL SUB-ASSEMBLY

  1. B173014
    Engage the 2 guides.

  1. Engage the 2 claws and 2 clips, and install the No. 2 instrument panel speaker panel sub-assembly.


33. INSTALL FRONT PILLAR GARNISH RH

  1. B173685E01
    Remove the protective cover.

  1. B173683E01
    Install a new clip <A> on the front pillar garnish RH.

  1. Engage the 3 guides and 2 clips, then install the front pillar garnish RH.


34. CONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP RH

  1. B173239E01
    Align the alignment mark (pink) on the weatherstrip with the protruding portion on the body indicated by the arrow in the illustration, and install the front door opening trim weatherstrip RH.

    NOTICE:
    After installation, check that the corners fit correctly.


35. INSTALL FRONT PILLAR GARNISH LH

  1. B173226E01
    Remove the protective cover.

  1. B173223E01
    Install a new clip <A> on the front pillar garnish LH.

  1. Engage the 3 guides and 2 clips, then install the front pillar garnish LH.


36. CONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP LH

  1. B173235E01
    Align the alignment mark (blue) on the weatherstrip with the protruding portion on the body indicated by the arrow in the illustration, and install the front door opening trim weatherstrip LH.

    NOTICE:
    After installation, check that the corners fit correctly.


37. INSTALL ENGINE SWITCH (w/ Smart Entry and Start System)

  1. A170658
    Engage the 2 claws to install the switch.

  1. Connect the switch connector.


38. INSTALL FRONT NO. 2 CONSOLE BOX INSERT (for LHD)

  1. B168374
    Engage the claw and 2 guides.

  1. Install the front No. 2 console box insert with the 3 screws <F> and clip.


39. INSTALL FRONT NO. 2 CONSOLE BOX INSERT (for RHD)

  1. B173038
    Engage the claw and 2 guides.

  1. Install the front No. 2 console box insert with the 3 screws <F> and clip.


40. INSTALL FRONT NO. 1 CONSOLE BOX INSERT (for LHD)

  1. B168373
    Engage the claw and 2 guides.

  1. Install the front No. 1 console box insert with the 3 screws <F> and 2 clips.


41. INSTALL FRONT NO. 1 CONSOLE BOX INSERT (for RHD)

  1. B173037
    Engage the claw and 2 guides.

  1. Install the front No. 1 console box insert with the 3 screws <F> and clip.


42. INSTALL CONSOLE BOX ASSEMBLY (w/o Rear Air Conditioning System)

  1. B173629
    Engage the 6 claws.

  1. B173628
    Install the console box assembly with the 4 bolts and 2 screws.


43. INSTALL CONSOLE BOX ASSEMBLY (w/ Rear Air Conditioning System)

  1. B175149
    Engage the 6 claws.

  1. Connect the connector.

  1. B181135
    Install the console box assembly with the 4 bolts and 2 screws.


44. INSTALL LOWER REAR CONSOLE BOX
  1. Install the lower rear console box.


45. INSTALL NO. 2 CONSOLE BOX DUCT (w/o Rear Air Conditioning System)

  1. B173013
    Install the No. 2 console box duct as shown in the illustration.


46. INSTALL UPPER CONSOLE PANEL SUB-ASSEMBLY

  1. B168372
    Connect the connector.

  1. Engage the 4 claws and 4 clips, and install the upper console panel sub-assembly.


47. INSTALL LOWER INSTRUMENT PANEL SUB-ASSEMBLY
  1. Connect each connector and clamp.

  1. B168370
    Engage the 4 claws and 3 clips.

  1. Install the lower instrument panel sub-assembly with the 2 bolts <B> and 3 screws <F>.


48. INSTALL NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY

  1. B173000
    Engage the 2 guides.

  1. Engage the 3 claws and install the No. 2 instrument panel under cover sub-assembly.


49. INSTALL COWL SIDE TRIM SUB-ASSEMBLY RH

HINT:
Use the same procedure for the RH side and the LH side.


50. INSTALL FRONT DOOR SCUFF PLATE RH

HINT:
Use the same procedure for the RH side and the LH side.


51. INSTALL LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY (for Manual Air Conditioning System)

  1. B168371
    Connect the hood lock control cable assembly.

  1. Connect each connector.

  1. Engage the 3 claws and 10 clips.

  1. Install the lower instrument panel finish panel sub-assembly with the 2 bolts <B>.


52. INSTALL LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY (for Automatic Air Conditioning System)

  1. B173009
    Connect the hood lock control cable assembly.

  1. Connect each connector and the aspirator duct.

  1. B173021
    Engage the 3 claws and 10 clips.

  1. Install the lower instrument panel finish panel sub-assembly with the 2 bolts <B>.


53. INSTALL COWL SIDE TRIM SUB-ASSEMBLY LH

  1. B173227
    Engage the claw and clip, install the cowl side trim sub-assembly LH.

  1. Install the clip.


54. INSTALL FRONT DOOR SCUFF PLATE LH

  1. B173224
    Engage the guide and the 8 claws, and install the front door scuff plate LH.


55. INSTALL RADIO RECEIVER ASSEMBLY WITH BRACKET (w/o Navigation System)
  1. Connect each connector.

  1. E150552
    Engage the 4 clips.

  1. E150551
    Install the radio receiver assembly with bracket with the 4 bolts.


56. INSTALL NAVIGATION RECEIVER ASSEMBLY WITH BRACKET (w/ Navigation System)
  1. Connect each connector.

  1. E150545
    Engage the 4 clips.

  1. E150544
    Install the navigation receiver assembly with bracket with the 4 bolts.


57. INSTALL INTEGRATION CONTROL AND PANEL ASSEMBLY WITH BRACKET (w/o Radio Receiver)
  1. Connect each connector.

  1. B173010
    Engage the 4 clips.

  1. Install the integration control and panel assembly with bracket with the 4 bolts <D>.


58. INSTALL HEATER CONTROL AND ACCESSORY ASSEMBLY (for Manual Air Conditioning System)
  1. Connect the connector.

  1. E150368
    Engage the 4 clips and install the heater control and accessory assembly.


59. INSTALL AIR CONDITIONING CONTROL ASSEMBLY (for Automatic Air Conditioning System)
  1. Connect the connector.

  1. E150367
    Engage the 4 clips and install the air conditioning control assembly.


60. INSTALL CENTER INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY (w/o Smart Entry and Start System)

  1. B184679E01
    Apply protective tape to the areas shown in the illustration.

  1. Connect each connector.

  1. Engage the 10 claws and 8 clips, and install the center instrument cluster finish panel assembly.

    NOTICE:
    Do not the damage the instrument panel safety pad assembly and lower instrument panel finish panel sub-assembly.


61. INSTALL CENTER INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY (w/ Smart Entry and Start System)

  1. B184681E01
    Apply protective tape to the areas shown in the illustration.

  1. Connect each connector.

  1. Engage the 10 claws and 8 clips, and install the center instrument cluster finish panel assembly.

    NOTICE:
    Do not the damage the instrument panel safety pad assembly and lower instrument panel finish panel sub-assembly.


62. INSTALL CENTER INSTRUMENT PANEL REGISTER ASSEMBLY

  1. B168369
    Engage the 2 claws and 5 clips, and install the center instrument panel register assembly.


63. INSTALL COMBINATION METER ASSEMBLY
  1. Connect the connector.

  1. B168365
    Install the combination meter assembly with the 4 screws <F>.


64. INSTALL INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY

  1. B168364
    Engage the 4 claws and 4 clips, and install the instrument cluster finish panel assembly.


65. POSITION FRONT WHEELS STRAIGHT AHEAD

66. INSTALL TURN SIGNAL SWITCH ASSEMBLY WITH SPIRAL CABLE SUB-ASSEMBLY

  1. C166129
    Using pliers, engage the claw. Install the turn signal switch assembly with spiral cable sub-assembly to the steering column assembly.

  1. Connect the connectors to the turn signal switch assembly with spiral cable sub-assembly.


67. INSTALL STEERING COLUMN COVER

  1. C165716
    Engage the claw to install the upper steering column cover.

  1. C166128
    Engage the 2 claws to install the lower steering column cover.

  1. C165715
    Install the 2 screws.

    Torque:
    2.0 N*m{ 20 kgf*cm , 18 in.*lbf }


68. ADJUST SPIRAL CABLE SUB-ASSEMBLY
  1. Check that the ignition switch is off.

  1. Check that the battery negative (-) cable is disconnected.

    CAUTION:
    Wait for at least 90 seconds after disconnecting the cable to prevent airbag deployment.

  1. C165096
    Rotate the spiral cable counterclockwise slowly by hand until it stops.

    NOTICE:
    Do not turn the spiral cable using the airbag wire harness.

  1. C165097E01
    Rotate the spiral cable clockwise approximately 2.5 turns to align the marks.

    NOTICE:
    Do not turn the spiral cable using the airbag wire harness.

    HINT:
    The spiral cable will rotate approximately 2.5 turns to both the left and right from the center.


69. INSTALL STEERING WHEEL ASSEMBLY

  1. C165708E01
    Align the matchmarks on the steering wheel assembly and steering main shaft.

  1. Install the steering wheel assembly set nut.

    Torque:
    50 N*m{ 510 kgf*cm , 37 ft.*lbf }

  1. Connect the connectors to the spiral cable sub-assembly.


70. INSPECT STEERING WHEEL CENTER POINT

71. INSTALL STEERING PAD
  1. Check that the ignition switch is off.

  1. Check that the battery negative (-) terminal is disconnected.

    CAUTION:
    Wait for at least 90 seconds after disconnecting the cable to prevent airbag deployment.

  1. C165092
    Support the steering pad with one hand as shown in the illustration.

  1. C165093
    Connect the 2 airbag connectors to the steering pad.

    NOTICE:
    When handling the airbag connector, take care not to damage the airbag wire harness.

  1. Connect the horn connector to the steering pad.

  1. Confirm that the circumference groove of the "TORX" screw fits in the screw case, and place the steering pad onto the steering wheel assembly.

  1. C166982E01
    Using a "TORX" socket wrench (T30), tighten the 2 "TORX" screws.

    Torque:
    8.8 N*m{ 90 kgf*cm , 78 in.*lbf }


72. INSTALL LOWER NO. 2 STEERING WHEEL COVER

  1. C165091
    Install the lower No. 2 steering wheel cover with the claw.


73. INSTALL LOWER NO. 3 STEERING WHEEL COVER

  1. C165090
    Install the lower No. 3 steering wheel cover with the claw.


74. CONNECT COOLER REFRIGERANT LIQUID PIPE A
  1. Remove the attached vinyl tape from the pipe.

  1. Sufficiently apply compressor oil to a new O-ring and fitting surface of the cooler refrigerant liquid pipe A.

    Compressor oil:
    ND-OIL 8 or equivalent

  1. Install the O-ring on the cooler refrigerant liquid pipe A.

  1. Install the cooler refrigerant liquid pipe A.


75. CONNECT NO. 1 COOLER REFRIGERANT SUCTION PIPE
  1. Remove the attached vinyl tape from the pipe.

  1. Sufficiently apply compressor oil to a new O-ring and the fitting surface of the No. 1 cooler refrigerant suction pipe.

    Compressor oil:
    ND-OIL 8 or equivalent

  1. Install the O-ring on the No. 1 cooler refrigerant suction pipe.

  1. E150370
    Move the hook connector in the direction indicated by the arrow in the illustration.

  1. Insert the pipe joint into the fitting hole securely and tighten the bolt.

    Torque:
    9.8 N*m{ 100 kgf*cm , 87 in.*lbf }


76. CONNECT HEATER WATER HOSE INLET

  1. E150372
    Install the heater inlet water hose and attach the clip.


77. CONNECT HEATER WATER HOSE OUTLET

  1. E150371
    Install the heater outlet water hose and attach the clip.


78. INSTALL COWL TOP OUTER PANEL SUB-ASSEMBLY

  1. C165926E01
    Install the outer cowl top panel sub-assembly with the 8 bolts and 6 nuts.

    Torque:
    Nut A:
    85 N*m{ 866 kgf*cm , 63 ft.*lbf }
    Bolt B:
    8.8 N*m{ 90 kgf*cm , 78 in.*lbf }
    Nut C:
    8.8 N*m{ 90 kgf*cm , 78 in.*lbf }

  1. C165925
    Engage the 4 clamps.


79. INSTALL WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY

  1. E150150
    Install the windshield wiper motor and link assembly with the 4 bolts.

    Torque:
    7.0 N*m{ 71 kgf*cm , 62 in.*lbf }

  1. Connect the connector.


80. INSTALL COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY

  1. Engage the 20 claws.

    E150149

  1. Install the cowl top ventilator louver sub-assembly with the 2 clips.

  1. E150146
    Engage the 2 claws and connect the front fender to cowl side seal LH.

  1. E150147
    Engage the 2 claws and connect the front fender to cowl side seal RH.


81. INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY RH
  1. Operate the wiper and stop the windshield wiper motor at the automatic stop position.

  1. When reinstalling:

    1. E112237E01
      Clean the wiper arm serrations.

    2. Clean the wiper pivot serrations with a wire brush.

  1. E147125E01
    Install the front wiper arm and blade assembly RH with the nut to the position shown in the illustration.

    Torque:
    24 N*m{ 245 kgf*cm , 18 ft.*lbf }

    HINT:
    Hold the wiper arm by hand when tightening the nut.

    Area
    Measurement
    A
    25.6 mm (1.00 in.)


82. INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY LH
  1. Operate the wiper and stop the windshield wiper motor at the automatic stop position.

  1. When reinstalling:

    1. E112237E01
      Clean the wiper arm serrations.

    2. Clean the wiper pivot serrations with a wire brush.

  1. E152618E01
    Install the front wiper arm and blade assembly LH with the nut to the position shown in the illustration.

    Torque:
    24 N*m{ 245 kgf*cm , 18 ft.*lbf }

    HINT:
    Hold the wiper arm by hand when tightening the nut.

    Area
    Measurement
    A
    31.9 mm (1.26 in.)

  1. Operate the front wipers while spraying washer fluid onto the windshield glass. Make sure that the front wipers function properly and the wipers do not come into contact with the vehicle body.


83. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).


84. INSPECT STEERING PAD

  1. C166979
    With the steering pad installed on the vehicle, perform a visual check. If there are any defects as mentioned below, replace the steering pad with a new one:
    1. Cuts, minute cracks or marked discoloration on the steering pad top surface or grooves.

  1. Make sure that the horn sounds.

    HINT:
    If the horn does not sound, inspect the horn system (Click here).


85. INSPECT SRS WARNING LIGHT
  1. Inspect the SRS warning light (Click here).


86. ADD ENGINE COOLANT
  1. Tighten the radiator drain cock plug by hand.

  1. Tighten the 2 cylinder block drain cock plugs.

    Torque:
    13 N*m{ 130 kgf*cm , 9 ft.*lbf } for cylinder block drain cock plugs

  1. Loosen the air drain cock plug from the water inlet housing.

  1. A169415E01
    Loosen the air drain plug at the top of the radiator 3 or 4 turns.

  1. Add TOYOTA Super Long Life Coolant (SLLC) to the radiator inlet opening until coolant overflows from the engine air drain cock hole. Then tighten the air drain cock plug to the water inlet housing.

    Torque:
    13 N*m{ 130 kgf*cm , 9 ft.*lbf } for air drain cock plug

  1. Continue to add TOYOTA Super Long Life Coolant (SLLC) to the radiator inlet opening until coolant overflows from the radiator air drain hole. Then close the air drain plug at the top of the radiator.

    Torque:
    1.5 N*m{ 15 kgf*cm , 13 in.*lbf } for air drain plug

    HINT:
    If the coolant level at the radiator inlet opening drops after squeezing the No. 1 and No. 2 radiator hoses, add coolant.

  1. Slowly fill the radiator with TOYOTA Super Long Life Coolant (SLLC).

    Standard capacity:
    w/o Engine oil cooler 
    Condition
    Specified Condition
    w/ Rear Heater
    11.0 liters (11.6 US qts, 9.7 Imp. qts)
    w/o Rear Heater
    8.8 liters (9.3 US qts, 7.7 Imp. qts)
    w/ Engine oil cooler 
    Condition
    Specified Condition
    w/ Rear Heater
    11.7 liters (12.4 US qts, 10.3 Imp. qts)
    w/o Rear Heater
    9.5 liters (10.1 US qts, 8.4 Imp. qts)

    HINT:
    1. TOYOTA vehicles are filled with TOYOTA SLLC at the factory. In order to avoid damage to the engine cooling system and other technical problems, only use TOYOTA SLLC or similar high quality ethylene glycol based non-silicate, non-amine, non-nitrite, non-borate coolant with long-life hybrid organic acid technology (coolant with long-life hybrid organic acid technology consists of a combination of low phosphates and organic acids).
    2. Contact your TOYOTA dealer for further details.

    NOTICE:
    Never use water as a substitute for engine coolant.

  1. Slowly pour coolant into the radiator reservoir tank until it reaches the FULL line.

  1. Squeeze the No. 1 and No. 2 radiator hoses several times by hand, and then check the level of the coolant.
    If the coolant level is low, add coolant.

  1. Bleed air from the cooling system.

    1. Warm up the engine until the thermostat opens. While the thermostat is open, circulate the coolant for several minutes.

      HINT:
      The thermostat open timing can be confirmed by squeezing the inlet radiator hose by hand, and checking when the engine coolant starts to flow inside the hose.

    2. Maintain the engine speed at 2500 to 3000 rpm.

    3. Squeeze the inlet and outlet radiator hoses several times by hand to bleed air.

      CAUTION:
      When squeezing the radiator hoses:
      1. Wear protective gloves.
      2. Be careful as the radiator hoses are hot.
      3. Keep your hands away from the radiator fan.

      NOTICE:
      1. Make sure that the radiator reservoir still has some coolant in it.
      2. If the coolant temperature gauge indicates an excessive temperature, turn off the engine and let it cool.
      3. If there is not enough coolant, the engine may overheat or be seriously damaged.
      4. If the radiator reservoir does not have enough coolant, perform the following: 1) stop the engine, 2) wait until the coolant has cooled down, and 3) add coolant until the reservoir is filled to the FULL line.

  1. Stop the engine and wait until the engine coolant cools down.

  1. Add engine coolant to the FULL line on the radiator reservoir.


87. INSPECT FOR COOLANT LEAK

CAUTION:
Do not remove the radiator cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.

NOTICE:
Before performing each inspection, turn the A/C switch off.

  1. A169405
    Fill the radiator with coolant and attach a radiator cap tester.

  1. Warm up the engine.

  1. Using the radiator cap tester, increase the pressure inside the radiator to 118 kPa (1.2 kgf/cm2, 17 psi), and check that the pressure does not drop.
    If the pressure drops, check the hoses, radiator and water pump for leaks. If no external leaks are found, check the heater core, cylinder block and cylinder head.


88. CHARGE WITH REFRIGERANT
  1. Perform vacuum purging using a vacuum pump.

  1. Charge with refrigerant HFC-134a (R134a).

    E143108E02

    Standard (w/o Rear Air Conditioning System):
    550 to 650 g (19.4 to 22.9 oz.)

    Standard (w/ Rear Air Conditioning System):
    720 to 820 g (25.4 to 28.9 oz.)

    SST
    09985-20010   (09985-02010, 09985-02050, 09985-02060, 09985-02070, 09985-02080, 09985-02090, 09985-02110, 09985-02130, 09985-02140, 09985-02150)

    NOTICE:
    1. Do not turn the A/C on before charging with refrigerant. Doing so will cause the cooler compressor to work without refrigerant, resulting in overheating of the cooler compressor.
    2. Approximately 100 g (3.53 oz.) of refrigerant may need to be charged after bubbles disappear. The refrigerant amount should be checked by quantity, not with the sight glass.

    HINT:
    Ensure that sufficient refrigerant is available to recharge the system when using a refrigerant recovery unit. Refrigerant recovery units are not always able to recover 100% of the refrigerant from an A/C system.


89. WARM UP ENGINE
  1. Keep the A/C switch on for at least 2 minutes to warm up the compressor.

    NOTICE:
    Be sure to warm up the compressor when turning the A/C on after removing and installing the cooler refrigerant lines (including the compressor), to prevent damage to the compressor.


90. INSPECT FOR REFRIGERANT LEAK
  1. After recharging with refrigerant gas, inspect for refrigerant leak using a halogen leak detector.

  1. Carry out the test under the following conditions:

    1. Make sure that the ignition switch is off.
    2. Secure good ventilation (the gas leak detector may react to volatile gases which are not refrigerant, such as evaporated gasoline and exhaust gas).
    3. Repeat the test 2 or 3 times.
    4. Make sure that there is some refrigerant remaining in the refrigeration system.
      When the compressor is off: approx. 392 to 588 kPa (4 to 6 kgf/cm2, 57 to 85 psi)

  1. I042222E25
    Using a gas leak detector, inspect for refrigerant leak from the refrigerant lines.

  1. N014519E06
    Bring the gas leak detector close to the drain hose with the detector's power off, and then turn the detector on.

    HINT:
    1. After the blower motor has stopped, let the cooling unit stand for more than 15 minutes.
    2. Bring the gas leak detector sensor under the drain hose.
    3. When bringing the gas leak detector close to the drain hose, make sure that the gas leak detector does not react to volatile gases.
      If it is not possible to avoid interference from volatile gases, the vehicle should be lifted up to allow testing.

  1. If a gas leak is not detected from the drain hose, remove the blower motor from the cooling unit. Insert the gas leak detector into the unit and perform the test.

  1. Disconnect the pressure switch connector and leave it for approximately 20 minutes. Bring the gas leak detector close to the pressure switch and perform the test.


91. INITIALIZE SERVO MOTOR
  1. Turn the ignition switch off.

  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to on.

  1. Press the A/C OFF switch.

  1. Turn the intelligent tester on.

  1. Enter the following menus: Body / Air Conditioner / Utility / Servomotor Initialization.

  1. According to the intelligent tester display, select the "Next" switch.

  1. According to the intelligent tester display, select the "Next" switch.

    HINT:
    During initialization, the AUTO indicator illuminates. When initialization is complete, the indicator turns off.

  1. According to the intelligent tester display, select the exit to finish the initialization.

← INSTALLATION (May 2007 – Jul 2008)INSTALLATION (Jul 2010 – Jul 2013) →