2007-2013 Highlander Kluger · Service Manual HEATER & AIR CONDITIONING SYSTEM

REMOVAL

Removal / installation · Vehicles built Aug 2008 – Jun 2010

Versions by build date: May 2007 – Jul 2008 Aug 2008 – Jun 2010 from Jul 2010


1. PRECAUTION
(Click here)

2. RECOVER REFRIGERANT FROM REFRIGERATION SYSTEM
  1. Start the engine.

  1. Turn the A/C switch on.

  1. Operate the cooler compressor at an engine speed of approximately 1000 rpm for 5 to 6 minutes to circulate the refrigerant. This causes most of the compressor oil from the various components of the A/C system to collect in the A/C compressor.

  1. Stop the engine.

  1. Recover the refrigerant from the A/C system using a refrigerant recovery unit.


3. POSITION FRONT WHEELS STRAIGHT AHEAD

4. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:
Wait for 90 seconds after disconnecting the cable to prevent the airbag from deploying (Click here).

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).


5. REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY LH

  1. E150144
    Remove the nut, and the front wiper arm and blade assembly LH.


6. REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY RH

  1. E150145
    Remove the nut, and the front wiper arm and blade assembly RH.


7. REMOVE COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY

  1. E150146
    Disengage the 2 claws and disconnect the front fender to cowl side seal LH.

  1. E150147
    Disengage the 2 claws and disconnect the front fender to cowl side seal RH.

  1. Remove the 2 clips.

    E150149

  1. Disengage the 20 claws and remove the cowl top ventilator louver sub-assembly.


8. REMOVE WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY

  1. E150150
    Disconnect the connector.

  1. Remove the 4 bolts, and the windshield wiper motor and link assembly.


9. REMOVE COWL TOP OUTER PANEL SUB-ASSEMBLY

  1. C165925
    Disengage the 4 clamps and separate the wiper wire harness from the outer cowl top panel sub-assembly.

  1. C165926
    Remove the 8 bolts, 6 nuts, and the outer cowl top panel sub-assembly.


10. DISCONNECT HEATER WATER HOSE OUTLET

  1. E150371
    Using pliers, grip the claws of the clip and slide the clip to disconnect the heater outlet water hose.

    NOTICE:
    1. Do not apply excessive force to the heater outlet water hose.
    2. Prepare a drain pan or cloth in case the coolant leaks.


11. DISCONNECT HEATER WATER HOSE INLET

  1. E150372
    Using pliers, grip the claws of the clip and slide the clip to disconnect the heater inlet water hose.

    NOTICE:
    1. Do not apply excessive force to the heater inlet water hose.
    2. Prepare a drain pan or cloth in case the coolant leaks.


12. DISCONNECT COOLER REFRIGERANT LIQUID PIPE A

  1. E150369
    Remove the bolt, and slide the hook connector.

  1. Disconnect the cooler refrigerant liquid pipe A.

  1. Remove the O-ring from the cooler refrigerant liquid pipe A.

    NOTICE:
    Seal the openings of the disconnected parts using vinyl tape to prevent entry of moisture and foreign matter.


13. DISCONNECT NO. 1 COOLER REFRIGERANT SUCTION PIPE
  1. Disconnect the No. 1 cooler refrigerant suction pipe.

  1. Remove the O-ring from the No. 1 cooler refrigerant suction pipe.

    NOTICE:
    Seal the openings of the disconnected parts using vinyl tape to prevent entry of moisture and foreign matter.


14. REMOVE LOWER NO. 3 STEERING WHEEL COVER

  1. C165090
    Disengage the claw and remove the lower No. 3 steering wheel cover.


15. REMOVE LOWER NO. 2 STEERING WHEEL COVER

  1. C165091
    Disengage the claw and remove the lower No. 2 steering wheel cover.


16. REMOVE STEERING PAD

  1. C166981E01
    Using a "TORX" socket wrench (T30), loosen the 2 "TORX" screws until the groove along the screw circumference catches on the screw case.

  1. C165092
    Pull out the steering pad from the steering wheel assembly and support the steering pad with one hand as shown in the illustration.

    NOTICE:
    When removing the steering pad, do not pull the airbag wire harness.

  1. C165094E01
    Disconnect the horn connector from the steering pad.

  1. Using a screwdriver with the tip wrapped with protective tape, disconnect the 2 airbag connectors and remove the steering pad.

    NOTICE:
    When handling the airbag connector, take care not to damage the airbag wire harness.


17. REMOVE STEERING WHEEL ASSEMBLY

  1. C165708E01
    Remove the steering wheel assembly set nut.

  1. Put matchmarks on the steering wheel assembly and the steering main shaft.

  1. Disconnect the connectors from the spiral cable.

  1. C165709E01
    Using SST, remove the steering wheel assembly.
    SST
    09950-50013   (09951-05010, 09952-05010, 09953-05020, 09954-05021)

    NOTICE:
    Apply a small amount of grease to the threads and tip of SST (09953-05020) before use.


18. REMOVE STEERING COLUMN COVER

  1. C165715
    Remove the 2 screws.

  1. C166128
    Disengage the 2 claws to remove the lower steering column cover.

  1. C165716
    Disengage the claw to remove the upper steering column cover.


19. REMOVE TURN SIGNAL SWITCH ASSEMBLY WITH SPIRAL CABLE SUB-ASSEMBLY
  1. Disconnect the connectors from the turn signal switch assembly with spiral cable sub-assembly.

  1. C166129
    Using pliers, grip the claws of the clip and remove the turn signal switch assembly with spiral cable sub-assembly.


20. REMOVE INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY

  1. B168364
    Disengage the 4 claws and 4 clips, and remove the instrument cluster finish panel assembly.


21. REMOVE COMBINATION METER ASSEMBLY

  1. B168365
    Remove the 4 screws <F>.

  1. Disconnect the connector and remove the combination meter assembly.


22. REMOVE CENTER INSTRUMENT PANEL REGISTER ASSEMBLY

  1. B168368E01
    Apply protective tape to the areas shown in the illustration.

  1. Using a moulding remover, disengage the 2 claws and 5 clips, and then remove the center instrument panel register assembly as shown in the illustration.


23. REMOVE CENTER INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY (w/o Smart Entry and Start System)

  1. B184678E01
    Apply protective tape to the areas shown in the illustration.

  1. Using a moulding remover, disengage the 10 claws and 8 clips starting from the upper part of the center instrument cluster finish panel assembly.

    NOTICE:
    Do not pull on the small storage compartment lid. Doing so may cause damage.

  1. Disconnect each connector and remove the center instrument cluster finish panel assembly.


24. REMOVE CENTER INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY (w/ Smart Entry and Start System)

  1. B184680E01
    Apply protective tape to the areas shown in the illustration.

  1. Using a moulding remover, disengage the 10 claws and 8 clips starting from the upper part of the center instrument cluster finish panel assembly.

    NOTICE:
    Do not pull on the small storage compartment lid. Doing so may cause damage.

  1. Disconnect each connector and remove the center instrument cluster finish panel assembly.


25. REMOVE HEATER CONTROL AND ACCESSORY ASSEMBLY (for Manual Air Conditioning System)

  1. E150368
    Disengage the 4 clips and remove the heater control and accessory assembly.

  1. Disconnect the connector.


26. REMOVE AIR CONDITIONING CONTROL ASSEMBLY (for Automatic Air Conditioning System)

  1. E150367
    Disengage the 4 clips and remove the air conditioning control assembly.

  1. Disconnect the connector.


27. REMOVE RADIO RECEIVER ASSEMBLY WITH BRACKET (w/o Navigation System)

  1. E150551
    Remove the 4 bolts.

  1. E150552
    Pull the radio receiver assembly with bracket toward the rear of the vehicle and disengage the 4 clips.

  1. Disconnect each connector and remove the radio receiver assembly with bracket.


28. REMOVE NAVIGATION RECEIVER ASSEMBLY WITH BRACKET (w/ Navigation System)

  1. E150544
    Remove the 4 bolts.

  1. E150545
    Pull the navigation receiver assembly with bracket toward the rear of the vehicle and disengage the 4 clips.

  1. Disconnect each connector and remove the navigation receiver assembly with bracket.


29. REMOVE INTEGRATION CONTROL AND PANEL ASSEMBLY WITH BRACKET (w/o Radio Receiver)

  1. B173010
    Remove the 4 bolts <D>.

  1. Disengage the 4 clips.

  1. Disconnect each connector and remove the integration control and panel assembly with bracket.


30. REMOVE FRONT DOOR SCUFF PLATE LH

  1. B173224
    Disengage the 8 claws and guide, and remove the front door scuff plate LH.


31. REMOVE COWL SIDE TRIM SUB-ASSEMBLY LH

  1. B173227
    Remove the clip.

  1. Disengage the clip and claw, and remove the cowl side trim sub-assembly LH.


32. REMOVE LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY (for Manual Air Conditioning System)

  1. B168371
    Remove the 2 bolts <B>.

  1. Disengage the 3 claws and 10 clips.

  1. Disconnect each connector.

  1. Disconnect the hood lock control cable assembly and remove the lower instrument panel finish panel sub-assembly.


33. REMOVE LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY (for Automatic Air Conditioning System)

  1. B173021
    Remove the 2 bolts <B>.

  1. Disengage the 3 claws and 10 clips.

  1. B173009
    Disconnect each connector and the aspirator duct.

  1. Disconnect the hood lock control cable assembly and remove the lower instrument panel finish panel sub-assembly.


34. REMOVE FRONT DOOR SCUFF PLATE RH

HINT:
Use the same procedure for the RH side and the LH side.


35. REMOVE COWL SIDE TRIM SUB-ASSEMBLY RH

HINT:
Use the same procedure for the RH side and the LH side.


36. REMOVE NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY

  1. B172999
    Disengage the 3 claws.

  1. Disengage the 2 guides and remove the No. 2 instrument panel under cover sub-assembly.


37. REMOVE LOWER INSTRUMENT PANEL SUB-ASSEMBLY

  1. B168370
    Remove the 2 bolts <B> and 3 screws <F>.

  1. Disengage the 4 claws and 3 clips.

  1. Disconnect each connector and clamp, and remove the lower instrument panel sub-assembly.


38. REMOVE UPPER CONSOLE PANEL SUB-ASSEMBLY

  1. B168372
    Disengage the 4 claws and 4 clips.

  1. Disconnect the connector and remove the upper console panel sub-assembly.


39. REMOVE NO. 2 CONSOLE BOX DUCT (w/o Rear Air Conditioning System)

  1. B173012
    Remove the No. 2 console box duct as shown in the illustration.


40. REMOVE LOWER REAR CONSOLE BOX
  1. Remove the lower rear console box.


41. REMOVE CONSOLE BOX ASSEMBLY (w/o Rear Air Conditioning System)

  1. B173628
    Remove the 4 bolts and 2 screws.

  1. B173629
    Disengage the 6 claws and remove the console box assembly.


42. REMOVE CONSOLE BOX ASSEMBLY (w/ Rear Air Conditioning System)

  1. B181135
    Remove the 4 bolts and 2 screws.

  1. B175149
    Disconnect the connector.

  1. Disengage the 6 claws, and remove the console box assembly.


43. REMOVE FRONT NO. 1 CONSOLE BOX INSERT (for LHD)

  1. B168373
    Using a clip remover, remove the 2 clips.

  1. Remove the 3 screws <F>.

  1. Disengage the claw and 2 guides, and then remove the front No. 1 console box insert.


44. REMOVE FRONT NO. 1 CONSOLE BOX INSERT (for RHD)

  1. B173037
    Using a clip remover, remove the clip.

  1. Remove the 3 screws <F>.

  1. Disengage the claw and 2 guides, and then remove the front No. 1 console box insert.


45. REMOVE FRONT NO. 2 CONSOLE BOX INSERT (for LHD)

  1. B168374
    Using a clip remover, remove the clip.

  1. Remove the 3 screws <F>.

  1. Disengage the claw and 2 guides, and then remove the front No. 2 console box insert.


46. REMOVE FRONT NO. 2 CONSOLE BOX INSERT (for RHD)

  1. B173038
    Using a clip remover, remove the clip.

  1. Remove the 3 screws <F>.

  1. Disengage the claw and 2 guides, and then remove the front No. 2 console box insert.


47. REMOVE ENGINE SWITCH (w/ Smart Entry and Start System)

  1. A170658
    Disconnect the switch connector.

  1. Disengage the 2 claws and remove the switch.


48. DISCONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP LH

  1. B173234
    Remove the front door opening trim weatherstrip LH.


49. REMOVE FRONT PILLAR GARNISH LH

  1. B173222E01
    Pull the upper part of the garnish toward the inside of the cabin and disengage the 2 clips.

  1. Cut off the clip <A>.

  1. Disengage the 3 guides and remove the front pillar garnish LH.

  1. Remove the clip <A>.

  1. B173225E01
    Protect the curtain shield airbag assembly.

    1. Cover the airbag with a 700 mm (27.56 in.) x 120 mm (4.72 in.) cloth or piece of nylon and fix the ends of the cover with tape, as shown in the illustration.

      NOTICE:
      Cover the curtain shield airbag with a protective cover as soon as the front pillar garnish is removed.


50. DISCONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP RH

HINT:
Use the same procedure for the RH side and the LH side.


51. REMOVE FRONT PILLAR GARNISH RH

  1. B173682E01
    Pull the upper part of the garnish toward the inside of the cabin and disengage the 2 clips.

  1. Cut off the clip <A>.

  1. Disengage the 3 guides and remove the front pillar garnish RH.

  1. Remove the clip <A>.

  1. B173684E01
    Protect the curtain shield airbag assembly.

    1. Cover the airbag with a 700 mm (27.56 in.) x 120 mm (4.72 in.) cloth or piece of nylon and fix the ends of the cover with tape, as shown in the illustration.

      NOTICE:
      Cover the curtain shield airbag with a protective cover as soon as the front pillar garnish is removed.


52. REMOVE NO. 1 INSTRUMENT PANEL SPEAKER PANEL SUB-ASSEMBLY

  1. B168375
    Disengage the 2 claws and 2 clips.

  1. Disengage the 2 guides and remove the No. 1 instrument panel speaker panel sub-assembly.


53. REMOVE FRONT NO. 2 SPEAKER ASSEMBLY (for LH Side)

  1. E150560
    Remove the 2 bolts and front No. 2 speaker assembly.

  1. Disconnect the connector.


54. REMOVE NO. 2 INSTRUMENT PANEL SPEAKER PANEL SUB-ASSEMBLY

  1. B173014
    Disengage the 2 claws and 2 clips.

  1. Disengage the 2 guides and remove the No. 2 instrument panel speaker panel sub-assembly.


55. REMOVE FRONT NO. 2 SPEAKER ASSEMBLY (for RH Side)

HINT:
Use the same procedures for the RH side and the LH side.


56. DISCONNECT INSTRUMENT PANEL WIRE ASSEMBLY

  1. C165103
    Disconnect the connector.


57. REMOVE INSTRUMENT PANEL SAFETY PAD ASSEMBLY (for Pole Antenna Type)
  1. Disconnect each connector.

  1. Remove the bolt <E>.

  1. Remove the 2 passenger airbag bolts <A>.

  1. Disengage each clamp.

    B173015E01

  1. Remove the 2 clips.

  1. Remove the 2 bolts <D> and nut <H>.

  1. Disengage the 5 claws and remove the instrument panel safety pad assembly.

    B168377E01


58. REMOVE INSTRUMENT PANEL SAFETY PAD ASSEMBLY (for Glass Antenna Type)
  1. Disconnect each connector.

  1. Remove the 2 passenger airbag bolts <A>.

  1. Disengage each clamp.

    B168376E01

  1. Remove the 2 clips.

  1. Remove the 2 bolts <D> and nut <H>.

  1. Disengage the 5 claws and remove the instrument panel safety pad assembly.

    B168377E01


59. REMOVE BRAKE PEDAL RETURN SPRING

  1. C165369
    Remove the brake pedal return spring from the push rod pin and instrument panel reinforcement.


60. REMOVE STOP LIGHT SWITCH ASSEMBLY

  1. E150073
    Disconnect the connector.

  1. E150074E01
    Loosen the stop light switch lock nut.

  1. Remove the stop light switch assembly as shown in the illustration.


61. SEPARATE BRAKE MASTER CYLINDER PUSH ROD CLEVIS
  1. Remove the clip and push rod pin, and separate the brake master cylinder push rod clevis from the brake pedal sub-assembly.


62. REMOVE BRAKE PEDAL SUPPORT SUB-ASSEMBLY (for LHD)

  1. C165371
    Disconnect the brake pedal load sensing switch connector and disengage the clamp.

  1. C165373
    Remove the 2 bolts and separate the brake pedal support sub-assembly from the instrument panel reinforcement.

  1. C165374
    Remove the 4 nuts and brake pedal support sub-assembly from the body.


63. REMOVE BRAKE PEDAL SUPPORT SUB-ASSEMBLY (for RHD)

  1. C165372
    Disconnect the brake pedal load sensing switch connector and disengage the clamp.

  1. C165375
    Remove the 2 bolts and separate the brake pedal support sub-assembly from the instrument panel reinforcement.

  1. C165376
    Remove the 4 nuts and brake pedal support sub-assembly from the body.


64. REMOVE DRIVER SIDE KNEE AIRBAG ASSEMBLY

  1. C165098
    Remove the 4 bolts.

  1. C165099
    Disengage the 2 hooks.

  1. C168059
    Pull out the driver side knee airbag assembly from the vehicle and support the driver side knee airbag assembly with one hand as shown in the illustration.

    NOTICE:
    When removing the driver side knee airbag assembly, do not pull the airbag wire harness.

  1. C168060E01
    Using a screwdriver with the tip wrapped with protective tape, disconnect the driver side knee airbag connector.

    NOTICE:
    When handling the airbag connector, take care not to damage the airbag wire harness.

  1. C165102
    Disengage the 2 claws and separate the DLC3 from the driver side knee airbag assembly.


65. REMOVE NO. 1 AIR DUCT SUB-ASSEMBLY (for LHD)

  1. C166133
    Disengage the 2 claws and remove the No. 1 air duct sub-assembly.


66. REMOVE NO. 1 AIR DUCT SUB-ASSEMBLY (for RHD)

  1. C166134
    Disengage the 2 claws and remove the No. 1 air duct sub-assembly.


67. SEPARATE STEERING INTERMEDIATE SHAFT SUB-ASSEMBLY

  1. C166145
    Loosen the bolt.

  1. C165544
    Remove the bolt and slide the steering intermediate shaft sub-assembly.

    NOTICE:
    Do not separate the steering intermediate shaft sub-assembly from the power steering link assembly.

  1. C165545E01
    Put matchmarks on the steering intermediate shaft sub-assembly and the power steering link assembly.

  1. Separate the steering intermediate shaft sub-assembly from the power steering link assembly.


68. REMOVE STEERING COLUMN ASSEMBLY (for LHD)

  1. C166138
    Disconnect the connector from the power steering ECU assembly.

    HINT:
    As shown in the illustration, turn the lock lever to disconnect the connector.

  1. C166140
    Disconnect the connector from the power steering ECU assembly.

  1. Disconnect the connectors and disengage the wire harness clamps from the steering column assembly.

  1. C166130
    Remove the bolt, 2 nuts, and the steering column assembly.


69. REMOVE STEERING COLUMN ASSEMBLY (for RHD)

  1. C166142
    Disconnect the connector from the power steering ECU assembly.

    HINT:
    As shown in the illustration, turn the lock lever to disconnect the connector.

  1. C166143
    Disconnect the connector from the power steering ECU assembly.

  1. Disconnect the connectors and disengage the wire harness clamps from the steering column assembly.

  1. C168095
    Remove the bolt, 2 nuts, and the steering column assembly.


70. DISCONNECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

  1. E151587
    Remove the 3 nuts and disconnect the instrument panel junction block assembly.


71. REMOVE POWER STEERING ECU ASSEMBLY (for LHD)

  1. C165549E01
    Disconnect the 4 connectors from the power steering ECU assembly.

  1. C166319
    Remove the 3 nuts and the power steering ECU assembly.


72. REMOVE POWER STEERING ECU ASSEMBLY (for RHD)

  1. C165550E01
    Separate the wire harness clamp from the power steering ECU assembly.

  1. Disconnect the 4 connectors from the power steering ECU assembly.

  1. C166320
    Remove the 3 nuts and the power steering ECU assembly.


73. REMOVE ECM (for RHD)
  1. Separate the harness connector (LHD).

  1. Disconnect the 5 ECM connectors.

  1. A171720E01
    Remove the wire harness clamp.

  1. Remove the 2 nuts, bolt and ECM.


74. REMOVE AIR CONDITIONING AMPLIFIER ASSEMBLY

  1. E150334
    Disconnect each connector.

  1. Remove the 2 screws and the air conditioning amplifier assembly.


75. REMOVE REAR NO. 1 AIR DUCT

  1. E150995E01
    Disengage the claw.

  1. Turn back the floor carpet as shown in the illustration.

  1. E150997
    Remove the clip.

  1. Disengage the clamp.

  1. Disengage the 2 claws and remove the rear No. 1 air duct.


76. REMOVE REAR NO. 3 AIR DUCT

  1. E150996E01
    Disengage the claw.

  1. Turn back the floor carpet as shown in the illustration.

  1. E150998
    Remove the clip.

  1. Disengage the 2 claws and remove the rear No. 3 air duct.


77. REMOVE NO. 1 CONSOLE BOX DUCT (w/o Rear Air Conditioning System)

  1. E151000
    Remove the clip and the No. 1 console box duct.


78. REMOVE CENTER HEATER TO REGISTER DUCT

  1. E150999
    Disengage the clamp.

  1. Disengage the 4 claws and remove the center heater to register duct.


79. REMOVE NO. 1 INSTRUMENT PANEL BRACE SUB-ASSEMBLY

  1. E151001
    Remove the bolt and disconnect the earth wire.

  1. Disengage each clamp.

  1. E151002
    Remove the 2 bolts.

  1. Remove the screw.

  1. Remove the 3 nuts and the No. 1 instrument panel brace sub-assembly.


80. REMOVE NO. 2 INSTRUMENT PANEL BRACE SUB-ASSEMBLY

  1. E151003
    Remove the bolt and disconnect the earth wire.

  1. Disengage each clamp.

  1. E151004
    Remove the bolt.

  1. Remove the screw.

  1. Remove the 3 nuts and the No. 2 instrument panel brace sub-assembly.


81. REMOVE INSTRUMENT PANEL REINFORCEMENT ASSEMBLY WITH AIR CONDITIONING UNIT (w/o PTC Heater)
  1. Disengage each clamp.

  1. Remove the 2 bolts and disconnect the 2 earth wires.

  1. Disconnect each connector.

  1. Remove the 2 nuts and bolt.

  1. Disconnect the blower motor connector.

    E151006E02

  1. Remove the 2 caps and the 2 bolts from the engine compartment side.

  1. Disconnect the cooler drain hose.

  1. Remove the nut.

    E151007

  1. Using a "TORX" socket wrench (T40), remove the 5 "TORX" bolts.

    HINT:
    The "TORX" bolts on the passenger side can be removed with the collars for adjustment.

  1. Using a 12 mm hexagon wrench, remove the 2 collars and the instrument panel reinforcement assembly with air conditioning unit.

    E151008E01


82. REMOVE INSTRUMENT PANEL REINFORCEMENT ASSEMBLY WITH AIR CONDITIONING UNIT (w/ PTC Heater)
  1. Disengage each clamp.

  1. Remove the 2 bolts and disconnect the 2 earth wires.

  1. Disconnect each connector.

  1. Remove the 2 nuts and bolt.

  1. Disconnect the blower motor connector.

  1. Disconnect the 2 quick heater connectors.

    E151005E02

  1. Remove the 2 caps and the 2 bolts from the engine compartment side.

  1. Disconnect the cooler drain hose.

  1. Remove the nut.

    E151007

  1. Using a "TORX" socket wrench (T40), remove the 5 "TORX" bolts.

    HINT:
    The "TORX" bolts on the passenger side can be removed with the collars for adjustment.

  1. Using a 12 mm hexagon wrench, remove the 2 collars and the instrument panel reinforcement assembly with air conditioning unit.

    E151008E01


83. REMOVE AIR CONDITIONING UNIT

  1. Remove the 3 bolts and the air conditioning unit from the instrument panel reinforcement assembly.

    E151012


84. REMOVE BLOWER ASSEMBLY

  1. E151015
    Disconnect the connector.

  1. Remove the 2 screws.

  1. Disengage the 2 claws and remove the blower assembly.

← REMOVAL (May 2007 – Jul 2008)REMOVAL (from Jul 2010) →