2007-2013 Highlander Kluger · Service Manual ENGINE

REMOVAL

Removal / installation · Vehicles built from Aug 2013

Versions by build date: May 2007 – Jul 2008 Aug 2008 – Jun 2010 Jul 2010 – Jul 2013 from Aug 2013


1. DISCHARGE FUEL SYSTEM PRESSURE

HINT:
Click here.


2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).


3. REMOVE ENGINE UNDER COVER ASSEMBLY

  1. A171849
    Remove the 2 bolts and engine under cover assembly RR.

  1. A171850
    Remove the 2 bolts, 2 screws, 5 clips and engine under cover assembly.


4. REMOVE NO. 1 ENGINE UNDER COVER

  1. A237657
    Remove the 6 bolts, 2 clips and No. 1 engine under cover.


5. DRAIN ENGINE COOLANT

NOTICE:
Do not remove the radiator cap sub-assembly, cylinder block drain cock plugs or radiator drain cock plug while the engine and radiator assembly are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.

  1. Loosen the radiator drain cock plug.

  1. Loosen the cylinder block drain cock plug. (for Bank 1)

  1. Loosen the cylinder block drain cock plug. (for Bank 2, w/ Cylinder Block Drain Cock Plug)

  1. Remove the radiator cap sub-assembly.

    A169414E03

    Text in Illustration 
    *1
    Radiator Cap Sub-assembly
    *2
    Cylinder Block Drain Cock Plug (for Bank 1)
    *3
    Cylinder Block Drain Cock Plug (for Bank 2, w/ Cylinder Block Drain Cock Plug)
    *4
    Radiator Drain Cock Plug
    *5
    Air Drain Cock Plug
    *6
    Air Drain Plug

    HINT:
    Collect the engine coolant in a container and dispose of it according to the regulations in your area.


6. REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY LH

  1. E150144
    Remove the nut, and the front wiper arm and blade assembly LH.


7. REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY RH

  1. E150145
    Remove the nut, and the front wiper arm and blade assembly RH.


8. REMOVE COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY

  1. E150146
    Disengage the 2 claws and disconnect the front fender to cowl side seal LH.

  1. E150147
    Disengage the 2 claws and disconnect the front fender to cowl side seal RH.

  1. Remove the 2 clips.

    E150149

  1. Disengage the 20 claws and remove the cowl top ventilator louver sub-assembly.


9. REMOVE WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY

  1. E150150
    Disconnect the connector.

  1. Remove the 4 bolts, and the windshield wiper motor and link assembly.


10. REMOVE OUTER COWL TOP PANEL SUB-ASSEMBLY

  1. C165925
    Disengage the 4 clamps and separate the wiper wire harness from the outer cowl top panel sub-assembly.

  1. C165926
    Remove the 8 bolts, 6 nuts, and the outer cowl top panel sub-assembly.


11. REMOVE V-BANK COVER SUB-ASSEMBLY

  1. A162365
    Hold the front of the V-bank cover sub-assembly and raise it to disengage the 2 clips on the front of the V-bank cover sub-assembly. Continue rising the V-bank cover sub-assembly to disengage the clip on the rear of the V-bank cover sub-assembly and remove the V-bank cover sub-assembly.

    NOTICE:
    Attempting to disengage both front and rear clips at the same time may cause the V-bank cover sub-assembly to break.


12. REMOVE AIR CLEANER CAP SUB-ASSEMBLY

  1. A170887
    Disconnect the 3 vacuum hoses.

  1. A170447
    Loosen the No. 1 air cleaner hose clamp.

  1. Disconnect the hose clamps and No. 2 ventilation hose.

  1. Disconnect the mass air flow meter connector.

  1. A170451
    Release the 2 clips, and remove the 2 bolts.

  1. Remove the air cleaner cap sub-assembly and air cleaner filter element.


13. DISCONNECT ENGINE ROOM MAIN WIRE

  1. A172968
    Disconnect the 5 harness clamps.


14. REMOVE THROTTLE BODY BRACKET

  1. A172966E01
    Remove the 2 bolts in the order shown in the illustration and remove the throttle body bracket.


15. REMOVE NO. 1 SURGE TANK STAY

  1. A172967E01
    Remove the 2 bolts in the order shown in the illustration and remove the No. 1 surge tank stay.


16. REMOVE INTAKE AIR SURGE TANK ASSEMBLY

  1. A171946E01
    Disconnect the 4 hoses.

    HINT:
    1. A: vapor feed hose
    2. B: union to check valve hose
    3. C: No. 1 ventilation hose
    4. D: vacuum hose

  1. A169363
    Disconnect the throttle body connector and clamp.

  1. Disconnect the connector.

  1. A169364
    Disconnect the 2 water by-pass hoses from the throttle body.

  1. A169366E02
    Remove the 4 bolts with a 5 mm socket hexagon wrench and 2 nuts in the order shown in the illustration.

  1. Remove the gasket from the intake air surge tank.


17. DISCONNECT FUEL TUBE SUB-ASSEMBLY

  1. A129469E02
    Remove the No. 2 fuel pipe clamp.

  1. Pinch the tube connector and pull out the fuel pipe.

    NOTICE:
    1. Check that there is no dirt or other foreign objects around the connector before disconnecting it. Clean the connector as necessary.
    2. It is necessary to prevent dirt or foreign objects from entering the quick connector. If dirt or foreign objects enter the connector, the O-rings may not seal properly.
    3. Only disconnect the quick connector by hand.
    4. Do not bend, kink or twist the nylon tubes. Protect the connector by covering it with a plastic bag.
    5. If the pipe and the connector are stuck, carefully try wiggling or pushing and pulling on the connector to release it. Pull the connector off the pipe carefully.


18. REMOVE FUEL DELIVERY PIPE SUB-ASSEMBLY

  1. A137341
    Disconnect the 6 fuel injector connectors.

  1. A129471
    Remove the 5 bolts and fuel delivery pipe sub-assembly together with the 6 fuel injectors.

    NOTICE:
    Be careful not to drop the fuel injectors when removing the fuel delivery pipe sub-assembly.

  1. A129472E01
    Remove the 6 injector vibration insulators from the intake manifold.


19. REMOVE FUEL INJECTOR ASSEMBLY

  1. A129473
    Pull out the fuel injectors from the fuel delivery pipe.

    NOTICE:
    If the injectors are to be reused, reinstall them to the same cylinder they came from.

  1. A129475E02
    Remove the 6 O-rings from the injectors.

← REMOVAL (Jul 2010 – Jul 2013)INSPECTION (May 2007 – Jul 2008) →