2007-2013 Highlander Kluger · Service Manual DRIVE LINE

REASSEMBLY

Removal / installation · Vehicles built from May 2007


1. INSTALL SIDE GEAR SHAFT HOLDER BEARING (for 2WD RH Side)
  1. Install a new bearing bracket hole snap ring to the front drive shaft assembly RH.

  1. C092032E02
    Using SST, install a new front drive shaft bearing.
    SST
    09527-30010  
    09527-10011  

    NOTICE:
    The bearing should be completely installed.

  1. C092033E02
    Using a snap ring expander, install a new drive shaft hole snap ring.


2. INSTALL FRONT DRIVE SHAFT DUST COVER (for 2WD RH Side)

  1. F045047E06
    Using SST and a press, install a new drive shaft dust cover.
    SST
    09726-40010  
    09527-10011  

    Distance:
    26.6 to 27.6 mm (1.047 to 1.0866 in.)

    NOTICE:
    1. The dust cover should be completely installed.
    2. Be careful not to damage the dust cover.


3. INSTALL FRONT DRIVE SHAFT DUST COVER RH (for 2WD RH Side)

  1. C129109E02
    Using SST and a press, install a new drive shaft dust cover RH until distance (A) from the tip of the center drive shaft to the drive shaft dust cover RH meets the specification.
    SST
    09527-10011  

    Distance (A):
    109.0 to 110.0 mm (4.2913 to 4.3307 in.)

    NOTICE:
    1. The dust cover should be completely installed.
    2. Be careful not to damage the dust cover.


4. INSTALL FRONT DRIVE SHAFT DUST COVER LH

  1. F041033E03
    Using SST and a press, install a new drive shaft dust cover LH.
    SST
    09527-10011  

    NOTICE:
    1. The dust cover should be completely installed.
    2. Be careful not to damage the dust cover.


5. INSTALL FRONT DRIVE SHAFT DUST COVER RH (for 4WD RH Side)

HINT:
Perform the same procedure as for the LH side.


6. INSTALL FRONT AXLE OUTBOARD JOINT BOOT

HINT:
W001994E04
Before installing the boots, wrap the splines of the drive shaft with vinyl tape to prevent the boot from being damaged.

  1. Install new parts to the outboard joint shaft in the following order:

    1. No. 2 front axle outboard joint boot clamp

    2. Front axle outboard joint boot

    3. Front axle outboard joint boot clamp

  1. Pack the front drive outboard joint shaft and front axle outboard joint boot with grease.

    Grease capacity 
    2WD
    164 to 184 g (5.8 to 6.5 oz.)
    4WD
    100 to 120 g (3.5 to 4.2 oz.)


7. INSTALL FRONT AXLE OUTBOARD JOINT BOOT CLAMP
  1. Hold the drive shaft lightly in a vise with aluminum plates in between.

    NOTICE:
    Do not overtighten the vise.

  1. Install the front axle outboard joint boot clamp onto the front axle outboard joint boot.

  1. C106162E08
    Place SST onto the front axle outboard joint boot clamp.
    SST
    09521-24010  

  1. Tighten SST so that the front axle outboard joint boot clamp is pinched.

    NOTICE:
    Do not overtighten SST.

  1. C106163E01
    Using SST, measure the clearance of the front axle outboard joint boot clamp.
    SST
    09240-00020  

    Clearance:
    0.5 to 1.5 mm (0.0197 to 0.0591 in.)

    NOTICE:
    If the measured value is greater than the specified value, retighten the clamp.


8. INSTALL NO. 2 FRONT AXLE OUTBOARD JOINT BOOT CLAMP
  1. Install the No. 2 front axle outboard joint boot clamp onto the front axle outboard joint boot.

  1. R010425E12
    Place SST onto the No. 2 front axle outboard joint boot clamp.
    SST
    09521-24010  

  1. Tighten SST so that the No. 2 front axle outboard joint boot clamp is pinched.

    NOTICE:
    Do not overtighten SST.

  1. R010426E08
    Using SST, measure the clearance of the No. 2 front axle outboard joint boot clamp.
    SST
    09240-00020  

    Clearance:
    0.5 to 1.5 mm (0.0197 to 0.0591 in.)

    NOTICE:
    If the measured value is greater than the specified value, retighten the clamp.


9. INSTALL FRONT DRIVE SHAFT DAMPER

  1. F040646E03
    Install the drive shaft damper to the drive shaft.

  1. Make sure that the damper is on the shaft groove.

  1. Set the distance as specified below.

    Distance 
    2WD
    LH
    228.0 to 232.0 mm (8.976 to 9.134 in.)
    RH
    231.0 to 235.0 mm (9.094 to 9.252 in.)
    4WD
    LH
    228.8 to 229.0 mm (9.008 to 9.016 in.)
    RH
    228.2 to 232.2 mm (8.984 to 9.142 in.)

  1. Install the drive shaft damper clamp onto the drive shaft damper.

    NOTICE:
    Be sure to install the clamp in the correct position.

  1. C108289E03
    Place SST onto the drive shaft damper clamp.
    SST
    09521-24010  

  1. Tighten SST so that the clamp is pinched.

    NOTICE:
    Do not overtighten SST.

  1. C108290
    Using SST, measure the clearance of the drive shaft damper clamp.
    SST
    09240-00020  

    Clearance:
    0.5 to 1.5 mm (0.0197 to 0.0591 in.)

    NOTICE:
    If the measured value is greater than the specified value, retighten the clamp.


10. INSTALL FRONT DRIVE INBOARD JOINT ASSEMBLY
  1. Wrap the splines of the outboard joint shaft with vinyl tape to prevent the boot from being damaged.

  1. C067417E13
    Install new parts to the front drive outboard joint shaft assembly in the following order:

    1. Front axle inboard joint boot clamp

    2. Front axle inboard joint boot

    3. No. 2 front axle inboard joint boot clamp

  1. Place the beveled side of the tripod joint axial spline toward the front drive outboard joint shaft assembly.

  1. Align the matchmarks placed before removal.

  1. Using a brass bar and hammer, tap in the tripod joint to the front drive outboard joint shaft assembly.

    NOTICE:
    1. Do not tap the roller.
    2. Be sure to install the tripod joint assembly in the correct direction.

  1. F045046
    Using a snap ring expander, install a new shaft snap ring.

  1. Pack the front drive inboard joint assembly and front axle inboard boot with grease.

    Grease capacity 
    2WD
    155 to 175 g (5.5 to 6.2 oz.)
    4WD
    106 to 126 g (3.7 to 4.4 oz.)

  1. F040222E18
    Align the matchmarks and install the front drive inboard joint assembly to the front drive outboard joint shaft assembly.


11. INSTALL FRONT AXLE INBOARD JOINT BOOT
  1. Install the front axle inboard joint boot to the front drive inboard joint assembly.

  1. C104911E04
    Check whether the drive shaft dimensions are within the following specifications.

    HINT:
    The following table shows dimension (A) of the drive shaft.

    Dimension (A) : 
    2WD
    LH
    601.1 to 605.1 mm (23.67 to 23.82 in.)
    RH
    920.4 to 924.4 mm (36.24 to 36.39 in.)
    4WD
    LH
    576.4 to 580.4 mm (22.69 to 22.85 in.)
    RH
    959.9 to 963.9 mm (37.79 to 37.95 in.)


12. INSTALL FRONT AXLE INBOARD JOINT BOOT CLAMP
  1. Hold the drive shaft lightly in a vise with aluminum plates in between.

    NOTICE:
    Do not overtighten the vise.

  1. Secure the inboard joint boot clamp onto the boot.

  1. D026925E08
    Place SST onto the inboard joint boot clamp.
    SST
    09521-24010  

  1. Tighten SST so that the front axle inboard joint boot clamp is pinched.

    NOTICE:
    Do not overtighten SST.

  1. D026926E01
    Using SST, measure the clearance of the front axle inboard joint boot clamp.
    SST
    09240-00020  

    Clearance:
    0.5 to 1.5 mm (0.0197 to 0.0591 in.)

    NOTICE:
    If the measured value is greater than the specified value, retighten the clamp.


13. INSTALL NO. 2 FRONT AXLE INBOARD JOINT BOOT CLAMP
  1. Hold the inboard joint shaft assembly in a vise with aluminium plates in between.

    NOTICE:
    Do not overtighten the vise.

  1. Secure the No. 2 front axle inboard joint boot clamp onto the boot.

  1. C108292E11
    Place SST onto the No. 2 front axle inboard joint boot clamp.
    SST
    09521-24010  

  1. Tighten SST so that the No. 2 front axle inboard joint boot clamp is pinched.

    NOTICE:
    Do not overtighten SST.

  1. C086270E09
    Using SST, measure the clearance of the No. 2 front axle inboard joint boot clamp.
    SST
    09240-00020  

    Clearance:
    0.5 to 1.5 mm (0.0197 to 0.0591 in.)

    NOTICE:
    If the measured value is greater than the specified value, retighten the clamp.


14. INSTALL FRONT DRIVE SHAFT HOLE SNAP RING
  1. Install a new front drive shaft hole snap ring.


15. INSPECT FRONT DRIVE SHAFT ASSEMBLY

  1. C091598E02
    Check that there is no excessive play in the outboard joint.

  1. Check that the inboard joint slides smoothly in the thrust direction.

  1. Check that there is no excessive play in the radial direction of the inboard joint.

  1. Check the boots for damage.

← INSPECTION (from May 2007)INSTALLATION (May 2007 – Jul 2008) →