B2274 ACC Monitor Malfunction
Diagnostic trouble codes · Vehicles built Aug 2008 – Jun 2010
Versions by build date: May 2007 – Jul 2008 Aug 2008 – Jun 2010 from Jul 2010
DESCRIPTION
This DTC is output if there is a problem in the ACCD output circuit, which is from the inside of the main body ECU to the ACC relay.- HINT:
- If the main body ECU is replaced with a new one while the negative (-) battery terminal is connected, the power source mode will be in IG-ON mode. When the battery is removed and reinstalled, the power source mode that was selected when the battery was removed is restored.
- After the main body ECU is replaced, perform the registration procedure for the engine immobiliser system.
| DTC No. |
DTC Detection Condition |
Trouble Area |
| B2274 |
ACC relay actuation circuit inside main body ECU or other related circuit is malfunctioning |
|
WIRING DIAGRAM


INSPECTION PROCEDURE
| 1. READ VALUE USING INTELLIGENT TESTER |
Connect the intelligent tester to the DLC3.
Turn the engine switch on (IG) and turn the intelligent tester main switch on.
Read the Data List according to the displays on the tester.
- HINT:
- When using the intelligent tester with the engine switch off, turn on and off any of the door courtesy light switches repeatedly at 1.5 second intervals or less until communication between the tester and vehicle starts.
Body: Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
ACC Relay Mon
Status of ACC Relay Monitor / ON or OFF
ON: Engine switch on (ACC)
OFF: Engine switch off
-
- OK:
- "ON" (engine switch on (ACC)) appears on the screen.
|
|
||||
| OK | |
| 2. CHECK ENGINE SWITCH CONDITION |
Check the power source mode changes.
When the key is inside the vehicle and the shift lever is in the P position, check that pressing the engine switch causes the power source mode to change as follows:
- OK:
- off → on (ACC) → on (IG) → off
|
|
||||
| OK | |
| Go to step 4 |
| 3. CHECK DTC OUTPUT |
Delete the DTCs (Click here).
Check for DTCs again.
- OK:
- No DTC is output.
|
|
||||
| OK | ||
| ||
| 4. INSPECT RELAY (ACC RELAY) |
Remove the ACC relay from the engine room relay block.

Measure the resistance according to the value(s) in the table below.
- Standard resistance:
Tester Connection
Condition
Specified Condition
3 - 5
When battery voltage is not applied to terminals 1 and 2
10 kΩ or higher
3 - 5
When battery voltage is applied to terminals 1 and 2
Below 1 Ω
|
|
||||
| OK | |
| 5. CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - INSTRUMENT PANEL JUNCTION BLOCK) |
Disconnect the D7 connector from the main body ECU.


Disconnect the 1I connector from the instrument panel junction block.
Measure the resistance according to the value(s) in the table below.
- Standard resistance:
Tester Connection
Condition
Specified Condition
1I-3 - D7-22 (ACCD)
Always
Below 1 Ω
D7-22 (ACCD) or 1I-3 - Body ground
Always
10 kΩ or higher
|
|
||||
| OK | |
| 6. CHECK HARNESS AND CONNECTOR |
Disconnect the 1A and 1F connectors from the instrument panel junction block.

Measure the resistance according to the value(s) in the table below.
- Standard resistance:
Tester Connection
Condition
Specified Condition
1F-10 - Body ground
Always
Below 1 Ω
Measure the voltage according to the value(s) in the table below.
- Standard voltage:
Tester Connection
Condition
Specified Condition
1A-1 - Body ground
Always
11 to 14 V
|
|
||||
| OK | ||
| ||
