2007-2013 Highlander Kluger · Service Manual BODY ELECTRICAL

TERMINALS OF ECU

System information · Vehicles built from Jul 2010

Versions by build date: May 2007 – Jun 2010 from Jul 2010


CHECK MAIN BODY ECU (INSTRUMENT PANEL JUNCTION BLOCK)

  1. Disconnect the main body ECU (instrument panel junction block) connector.
    B139428E11

  2. Measure the resistance and voltage between each terminal of the wire harness side connectors and body ground.

    Symbols (Terminal No.)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    D6-7 (RCTY) - Body ground
    GR - Body ground
    Rear courtesy light switch RH input
    Rear door RH CLOSED (OFF) → OPEN (ON)
    10 kΩ or higher → Below 1 Ω
    D6-21 (PCTY) - Body ground
    SB*1 - Body ground
    Passenger side courtesy light switch input
    Passenger side door CLOSED (OFF) → OPEN (ON)
    10 kΩ or higher → Below 1 Ω
    G*2 - Body ground
    D6-25 (BCTY) - Body ground
    L - Body ground
    Back door courtesy light switch input
    Back door CLOSED (OFF) → OPEN (ON)
    10 kΩ or higher → Below 1 Ω
    D7-24 (DCTY) - Body ground
    G*1 - Body ground
    Driver side door courtesy light switch input
    Driver side door CLOSED (OFF) → OPEN (ON)
    10 kΩ or higher → Below 1 Ω
    SB*2 - Body ground
    D9-5 (KSW) - Body ground
    GR - Body ground
    Unlock warning switch input
    No key in ignition key cylinder (OFF) → Key inserted (ON)
    10 kΩ or higher → Below 1 Ω
    1A-1 (ACC) - Body ground
    B - Body ground
    Ignition power supply (ACC signal)
    Ignition switch ACC → OFF
    10 to 14 V → Below 1 V
    1A-1 (IG) - Body ground
    B - Body ground
    Ignition power supply (IG signal)
    Ignition switch ON → OFF
    10 to 14 V → Below 1 V
    1D-16 (ALTB) - Body ground
    W - Body ground
    +B (power system alternator system) power supply
    Always
    10 to 14 V
    1F-10 (GND1) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    1D-10 (BECU) - Body ground
    W - Body ground
    +B power supply
    Always
    10 to 14 V
    1M-9 (GND2) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    1O-7 (LCTY) - Body ground
    B - Body ground
    Rear courtesy light switch LH input
    Rear door LH CLOSED (OFF) → OPEN (ON)
    10 kΩ or higher → Below 1 Ω

    HINT:
    1. *1: for LHD
    2. *2: for RHD

    If the result is not as specified, there may be a malfunction on the wire harness side.

  3. Reconnect the main body ECU (instrument panel junction block) connectors.

  4. Measure the voltage between each terminal of the wire harness side connectors and body ground.

    Symbols (Terminal No.)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    D7-1 (TR+) - Body ground
    LG - Body ground
    Back door opener motor input
    Back door CLOSED (LOCKED) → OPEN (UNLOCKED)
    Below 1 V → 10 to 14 V*1
    D8-4 (HAZ) - Body ground
    O - Body ground
    Turn signal flasher relay signal
    Any transmitter switch is pressed → not pressed
    Below 1 V → Pulse generation*2
    D9-7 (BZR) - Body ground
    R - Body ground
    Wireless door lock buzzer
    Wireless door lock buzzer OFF → ON
    Below 1 V → 10 to 14 V

    HINT:
    1. *1: When operating the motor
    2. *2: When operating the answer back function

← TERMINALS OF ECU (May 2007 – Jun 2010)DIAGNOSIS SYSTEM (from May 2007) →