2007-2013 Highlander Kluger · Service Manual SECURITIES

TERMINALS OF ECU

System information · Vehicles built from Jul 2010

Versions by build date: May 2007 – Jun 2010 from Jul 2010


CHECK MAIN BODY ECU (INSTRUMENT PANEL JUNCTION BLOCK)

  1. Disconnect the main body ECU (instrument panel junction block) connectors.
    B112605E15

  2. Measure the resistance and voltage between each terminal of the wire harness side connectors and body ground.

    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    D6-7 (RCTY) - Body ground
    GR - Body ground
    Rear courtesy light switch RH input
    Rear door RH CLOSED (OFF) → OPEN (ON)
    10 kΩ or higher → Below 1 Ω
    D6-21 (PCTY) - Body ground
    SB*1 - Body ground
    Passenger side courtesy light switch input
    Passenger side door CLOSED (OFF) → OPEN (ON)
    10 kΩ or higher → Below 1 Ω
    G*2 - Body ground
    D6-25 (BCTY) - Body ground
    L - Body ground
    Back door courtesy light switch input
    Back door CLOSED (OFF) → OPEN (ON)
    10 kΩ or higher → Below 1 Ω
    D7-24 (DCTY) - Body ground
    G*1 - Body ground
    Driver side door courtesy light switch input
    Driver side door CLOSED (OFF) → OPEN (ON)
    10 kΩ or higher → Below 1 Ω
    SB*2 - Body ground
    D9-8 (GHSW) - Body ground
    O - Body ground
    Glass hatch courtesy switch
    Glass hatch CLOSED (OFF) → OPEN (ON)
    10 kΩ or higher → Below 1 Ω
    1A-1 (ACC) - Body ground
    B - Body ground
    Ignition power supply (ACC signal)
    Engine switch ON (ACC) → OFF
    11 to 14 V → Below 1 V
    1A-1 (IG) - Body ground
    B - Body ground
    Ignition power supply (IG signal)
    Engine switch ON (IG) → OFF
    11 to 14 V → Below 1 V
    1D-16 (ALTB) - Body ground
    W - Body ground
    +B (power system alternator system) power supply
    Always
    11 to 14 V
    1F-10 (GND1) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    1M-9 (GND2) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    1O-7 (LCTY) - Body ground
    B - Body ground
    Rear courtesy light switch LH input
    Rear door LH CLOSED (OFF) → OPEN (ON)
    10 kΩ or higher → Below 1 Ω

    HINT:
    1. *1: for LHD
    2. *2: for RHD
    3. If the result is not as specified, there may be a malfunction on the wire harness side.

  3. Reconnect the main body ECU (instrument panel junction block) connectors.

  4. Measure the voltage between each terminal of the wire harness side connectors and body ground.

    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    D8-4 (HAZ) - Body ground
    O - Body ground
    Turn signal flasher relay signal
    System is in alarm sounding state
    Below 1 V
    1D-11 (HORN) - Body ground
    GR - Body ground
    Vehicle horn drive
    Vehicle horn is sounding
    (Theft deterrent system is in alarm sounding state)
    Pulse generation
    (Below 1 V ← → 12 V)
    If the result is not as specified, the main body ECU (instrument panel junction block) may have a malfunction.


CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) ASSEMBLY
  1. Disconnect the D35 and D36 ECU connectors.

  2. Measure the resistance and voltage according to the value(s) in the table below.
    E125964E12

    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    D35-24 (HSW) - Body ground
    R - Body ground
    Engine hood courtesy switch
    Engine hood CLOSED (OFF) → OPEN (ON)
    Below 1 Ω → 10 kΩ or higher
    D36-1 (+B) - D36-17 (E)
    B - B
    Battery power supply
    Always
    11 to 14 V
    D36-17 (E) - Body ground
    B - Body ground
    Ground
    Always
    Below 1 Ω
    If the result is not as specified, there may be a malfunction on the wire harness side.

  3. Reconnect the D35 and D36 ECU connectors.

  4. Measure the voltage according to the value(s) in the table below.

    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    D35-20 (SH-) - Body ground
    W - Body ground
    Security horn drive
    Security horn is sounding (Theft deterrent system is in alarm sounding state)
    Pulse generation
    (Below 1 V ← → 12 V)
    D36-2 (IND) - Body ground
    W - Body ground
    Security indicator light output
    Security indicator light is on (It comes on only in alarm sounding state. It flashes when immobiliser is operating.)
    3 to 6 V
    If the result is not as specified, the certification ECU (smart key ECU assembly) may have a malfunction.

← TERMINALS OF ECU (May 2007 – Jun 2010)DIAGNOSIS SYSTEM (from May 2007) →