2007-2013 Highlander Kluger · Service Manual BODY ELECTRICAL

TERMINALS OF ECU

System information · Vehicles built from May 2007


CHECK MAIN BODY ECU (INSTRUMENT PANEL JUNCTION BLOCK)

  1. Disconnect the main body ECU (instrument panel junction block) connectors.
    B139428E11

  2. Measure the resistance and voltage between each terminal of the wire harness side connectors and body ground.

    Symbols (Terminal No.)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    D6-7 (RCTY) - Body ground
    GR - Body ground
    Rear courtesy light switch RH input
    Rear door RH CLOSED (OFF) → OPEN (ON)
    10 kΩ or higher → Below 1 Ω
    D6-21 (PCTY) - Body ground
    SB - Body ground*1
    Passenger side courtesy light switch input
    Passenger side door CLOSED (OFF) → OPEN (ON)
    10 kΩ or higher → Below 1 Ω
    G - Body ground*2
    D6-25 (BCTY) - Body ground
    L - Body ground
    Back door courtesy light switch input
    Back door CLOSED (OFF) → OPEN (ON)
    10 kΩ or higher → Below 1 Ω
    D7-24 (DCTY) - Body ground
    G - Body ground*1
    Driver side door courtesy light switch input
    Driver side door CLOSED (OFF) → OPEN (ON)
    10 kΩ or higher → Below 1 Ω
    SB - Body ground*2
    1A-1 (ACC) - Body ground
    B - Body ground
    Ignition power supply (ACC signal)
    Engine switch on (ACC) → off
    10 to 14 V → Below 1 V
    1A-1 (IG) - Body ground
    B - Body ground
    Ignition power supply (IG signal)
    Engine switch on (IG) → off
    10 to 14 V → Below 1 V
    1D-16 (ALTB) - Body ground
    W - Body ground
    +B (power system alternator system) power supply
    Always
    10 to 14 V
    1F-10 (GND1) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    1M-9 (GND2) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    1O-7 (LCTY) - Body ground
    B - Body ground
    Rear courtesy light switch LH input
    Rear door LH CLOSED (OFF) → OPEN (ON)
    10 kΩ or higher → Below 1 Ω

    HINT:
    1. *1: for LHD
    2. *2: for RHD

    If the result is not as specified, there may be a malfunction on the wire harness side.

  3. Reconnect the main body (instrument panel Junction block) connectors.

  4. Measure the voltage between each terminal of the wire harness side connectors and body ground.

    Symbols (Terminal No.)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    D7-1 (TR+) - Body ground
    LG - Body ground*3
    Back door opener motor
    Back door CLOSED (LOCKED) → OPEN (UNLOCKED)
    Below 1 V → 11 to 14 V*1
    D8-4 (HAZ) - Body ground
    O - Body ground
    Turn signal flasher relay signal
    Any transmitter switch is pressed → not pressed
    Below 1 V → 11 to 14 V*2

    HINT:
    1. *1: When operating the motor.
    2. *2: When operating the answer back function.
    3. *3: w/o Power Back Door System


CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY))
B122343E08
  1. Disconnect the D36 ECU connector.

  2. Measure the resistance and voltage according to the value(s) in the table below.

    Terminal No. (Symbols)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    D36-17 (E) - Body ground
    B - Body ground
    Ground
    Always
    Below 1 Ω
    D36-1 (+B) - D36-17 (E)
    B - B
    Battery power supply
    Always
    11 to 14 V
    D36-18 (IG) - D36-17 (E)
    G - B
    IG power supply
    Engine switch on (IG)
    11 to 14 V
    Engine switch off
    Below 1 V
    1. If the result is not as specified, there may be a malfunction on the wire harness side.

  3. Reconnect the D36 ECU connector.

  4. Measure the voltage according to the value(s) in the table below.

    Terminal No. (Symbols)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    D36-39 (RSSI) - D36-17 (E)
    B - B
    Door control receiver output signal
    Engine switch off, all doors closed and transmitter switch not pressed
    11 to 14 V
    Engine switch off, all doors closed and transmitter switch pressed
    Below 1 V
    D36-38 (RDA) - D36-17 (E)
    Y - B
    Door control receiver output signal
    Engine switch off, all doors closed and transmitter switch not pressed
    4.6 to 5.4 V
    Engine switch off, all doors closed and transmitter switch pressed
    Pulse generation
    D36-29 (RC0) - D36-17 (E)
    V - B
    Supply battery to door control receiver
    Engine switch off, all doors closed and transmitter switch pressed
    4.6 to 5.4 V
    D36-21 (BZR) - Body ground
    R - Body ground
    Wireless door lock buzzer signal
    Wireless door lock buzzer OFF → ON
    Below 1 V → Pulse generation
    1. If the result is not as specified, the ECU may have a malfunction.

← PROBLEM SYMPTOMS TABLE (from Jul 2012)DIAGNOSIS SYSTEM (from May 2007) →