2007-2013 Highlander Kluger · Service Manual DRIVE LINE

REMOVAL

Removal / installation · Vehicles built from Jul 2010

Versions by build date: May 2007 – Jul 2008 Aug 2008 – Jun 2010 from Jul 2010


1. REMOVE NO. 1 TRANSFER CASE PLUG

  1. C082977E04
    Remove the No. 1 transfer case plug.

  1. Remove the No. 1 gasket from the No. 1 transfer case plug.


2. REMOVE TRANSFER DRAIN PLUG
  1. Remove the transfer drain plug and bleed the oil.

  1. Remove the drain gasket from the transfer drain plug.


3. REMOVE ENGINE UNDER COVER ASSEMBLY

  1. A171849
    Remove the 2 bolts and engine under cover assembly RR.

  1. A171850
    Remove the 2 bolts, 2 screws, 5 clips and engine under cover assembly.


4. REMOVE NO. 1 ENGINE UNDER COVER

  1. A237657
    Remove the 6 bolts, 2 clips and No. 1 engine under cover.


5. REMOVE NO. 2 ENGINE UNDER COVER

  1. A171854
    Remove the 2 bolts and No. 2 engine under cover.


6. DRAIN AUTOMATIC TRANSAXLE FLUID
  1. Remove the drain plug and gasket, and drain ATF.

  1. Install a new gasket and the drain plug.

    Torque:
    49 N*m{ 500 kgf*cm , 36 ft.*lbf }


7. REMOVE FRONT WHEEL

8. REMOVE FRONT AXLE HUB NUT

  1. C167528E01
    Using SST and a hammer, release the staked part of the front axle hub nut.
    SST
    09930-00010  

    NOTICE:
    Loosen the staked part of the nut completely, otherwise the threads of the drive shaft may be damaged.

  1. While applying the brakes, remove the front axle hub nut.


9. SEPARATE FRONT STABILIZER LINK ASSEMBLY

  1. C165915
    Remove the nut and separate the front stabilizer link assembly from the front shock absorber.

    HINT:
    If the ball joint turns together with the nut, use a hexagon wrench (6 mm) to hold the stud.


10. SEPARATE FRONT SPEED SENSOR

  1. C165818E03
    Remove the bolt and resin clamp, and separate the front speed sensor.


11. SEPARATE TIE ROD END SUB-ASSEMBLY
  1. Remove the cotter pin and the nut.

  1. C165542E01
    Install SST to the tie rod end.
    SST
    09960-20010   (09961-02060)

    NOTICE:
    Make sure that the upper ends of the tie rod end and SST are aligned.

  1. Using SST, separate the tie rod end from the steering knuckle.

    C165543E01

    SST
    09960-20010   (09961-02010)

    NOTICE:
    1. When securing SST to the steering knuckle, be sure to tighten the string of SST to prevent it from falling.
    1. Install SST so that A and B are parallel.
    1. Be sure to place the wrench on the part indicated in the illustration.
    1. Do not damage the front disc brake dust cover.
    1. Do not damage the ball joint dust cover.
    1. Do not damage the steering knuckle.


12. SEPARATE NO. 1 FRONT SUSPENSION LOWER ARM

  1. C165929
    Remove the bolt and 2 nuts, and separate the front lower suspension arm from the front lower ball joint.


13. SECURE FRONT AXLE HUB SUB-ASSEMBLY

  1. F045045E04
    Using SST, secure the front axle hub bearing.
    SST
    09608-16042   (09608-02021, 09608-02041)

    NOTICE:
    The hub bearing may be damaged if it is subjected to the vehicle's full weight, such as when moving the vehicle with the drive shaft removed. If it is necessary to place the vehicle's weight on the hub bearing, first support it with SST.


14. REMOVE FRONT DRIVE SHAFT ASSEMBLY RH

HINT:
Perform the same procedure as for the LH side.


15. FRONT DRIVE SHAFT HOLE SNAP RING

  1. C057543E04
    Using a screwdriver, remove the front drive shaft hole snap ring.


16. REMOVE TRANSFER RH BEARING RETAINER OIL SEAL

  1. C083628E02
    Using SST, remove the transfer RH bearing retainer oil seal.
    SST
    09308-00010  

    NOTICE:
    Do not damage the oil-seal-fitted surface of the case.

← REMOVAL (Aug 2008 – Jun 2010)INSTALLATION (May 2007 – Jul 2008) →