2007-2013 Highlander Kluger · Service Manual DRIVE LINE

DISASSEMBLY

Removal / installation · Vehicles built from May 2007


1. REMOVE REAR DIFFERENTIAL CARRIER COVER

  1. C167091
    Remove the 8 bolts from the rear differential carrier cover.

  1. Using a brass bar and a hammer, separate the rear differential carrier cover from rear differential carrier assembly.


2. REMOVE REAR DIFFERENTIAL BREATHER PLUG

  1. C169481
    Remove the rear differential breather plug from the rear differential carrier cover.


3. SECURE REAR DIFFERENTIAL CARRIER ASSEMBLY

  1. C171643
    Set the differential carrier to an overhaul stand, etc. as shown in the illustration.


4. INSPECT RUNOUT OF DIFFERENTIAL RING GEAR

  1. C167092
    Using a dial indicator, check the runout of the differential ring gear.

    Maximum runout:
    0.07 mm (0.0028 in.)

    If the runout exceeds the specified maximum value, remove the ring gear and check the runout of the differential case.


5. INSPECT DIFFERENTIAL RING GEAR BACKLASH

  1. C167093
    Using a dial indicator, check the backlash of the differential ring gear.

    Backlash:
    0.13 to 0.18 mm (0.0051 to 0.0071 in.)

    If the backlash is not within the specification, adjust the side bearing preload or repair as necessary.


6. INSPECT TOOTH CONTACT BETWEEN RING GEAR AND DRIVE PINION

  1. C171644
    Coat 3 or 4 teeth at 3 different positions on the differential ring gear with Prussian blue.

  1. Hold the rear drive pinion companion flange sub-assembly firmly and rotate the differential ring gear in both directions.

  1. Inspect the tooth contact pattern.

    SA01653E05
    If the teeth are not contacting properly, use the following table to select a proper washer for correction.

    Washer thickness:
    Thickness mm (in.)
    Thickness mm (in.)
    Thickness mm (in.)
    2.26 to 2.28 (0.0890 to 0.0898)
    2.41 to 2.43 (0.0949 to 0.0957)
    2.56 to 2.58 (0.1008 to 0.1016)
    2.29 to 2.31 (0.0902 to 0.0909)
    2.44 to 2.46 (0.0961 to 0.0969)
    2.59 to 2.61 (0.1020 to 0.1028)
    2.32 to 2.34 (0.0913 to 0.0921)
    2.47 to 2.49 (0.0972 to 0.0980)
    2.62 to 2.64 (0.1031 to 0.1039)
    2.35 to 2.37 (0.0925 to 0.0933)
    2.50 to 2.52 (0.0984 to 0.0992)
    2.65 to 2.67 (0.1043 to 0.1051)
    2.38 to 2.40 (0.0937 to 0.0945)
    2.53 to 2.55 (0.0996 to 0.1004)
    2.68 to 2.70 (0.1055 to 0.1063)


7. INSPECT DIFFERENTIAL PINION AND SIDE GEAR BACKLASH

  1. C167094
    Using a dial indicator, check the backlash of the differential side gear while holding one of the pinion gears toward the differential case assembly.

    Backlash:
    0.05 to 0.20 mm (0.0020 to 0.0079 in.)

    If the backlash is not within the specification, install the 2 differential side gear thrust washers of different thicknesses (Click here).

    HINT:
    Measure the backlash of the differential side gear with the rear differential pinion shaft installed.


8. INSPECT RUNOUT OF REAR DRIVE PINION COMPANION FLANGE SUB-ASSEMBLY

  1. C120866E02
    Using a dial indicator, measure the runout of the rear drive pinion companion flange sub-assembly vertically and horizontally.

    (A):
    30 mm (1.18 in.)

    Maximum runout:
    0.10 mm (0.0039 in.)

    If the runout is greater than the maximum value, replace the rear drive pinion companion flange sub-assembly.


9. INSPECT DIFFERENTIAL DRIVE PINION PRELOAD

  1. C171654
    Using a torque wrench, measure the preload of the differential drive pinion.

    Drive pinion preload (Initial):
    Preload
    0.6 to 0.9 N*m (6.1 to 9.2 kgf*cm, 5.3 to 8.0 in.*lbf)

    If the preload is not within the specified range, adjust the total preload or repair as necessary.


10. INSPECT TOTAL PRELOAD

  1. C171654
    Using a torque wrench, measure the total preload.

    Total preload (Initial):
    Drive pinion preload plus 0.3 to 0.5 N*m (3.1 to 5.1 kgf*cm, 2.7 to 4.4 in.*lbf)

    If the preload is not within the specified range, adjust the total preload or repair as necessary.


11. REMOVE REAR DIFFERENTIAL SIDE GEAR SHAFT OIL SEAL

  1. C167095E01
    Using SST, remove the 2 rear differential side gear shaft oil seals from the rear differential carrier sub-assembly.
    SST
    09308-00010  


12. REMOVE REAR DRIVE PINION NUT

  1. C168604E01
    Using SST and a hammer, unstake the staked part of the rear drive pinion nut.
    SST
    09930-00010  

  1. C165857E01
    Using SST to hold the rear drive pinion companion flange sub-assembly, remove the rear drive pinion nut.
    SST
    09330-00021  


13. REMOVE REAR DRIVE PINION COMPANION FLANGE SUB-ASSEMBLY

  1. C169428E01
    Using SST, remove the rear drive pinion companion flange sub-assembly.
    SST
    09950-30012   (09951-03010, 09953-03010, 09954-03010, 09955-03030, 09956-03020)


14. REMOVE REAR DIFFERENTIAL DUST DEFLECTOR

  1. C167099E01
    Using SST and a press, remove the rear differential dust deflector.
    SST
    09950-60010   (09951-00360)
    09950-70010   (09951-07150)
    09950-00020  


15. REMOVE REAR DIFFERENTIAL CARRIER OIL SEAL

  1. C167097E01
    Using SST, remove the rear differential carrier oil seal from the rear differential carrier sub-assembly.
    SST
    09308-10010  


16. REMOVE REAR DIFFERENTIAL DRIVE PINION OIL SLINGER

17. REMOVE REAR DRIVE PINION FRONT TAPERED ROLLER BEARING

  1. C167098E01
    Using SST, remove the rear drive pinion front tapered roller bearing from the differential drive pinion.
    SST
    09556-22010  


18. REMOVE REAR DIFFERENTIAL DRIVE PINION BEARING SPACER

19. REMOVE REAR DIFFERENTIAL CASE

  1. C165858E01
    Put matchmarks on the rear differential bearing cap and rear differential carrier sub-assembly.

  1. Remove the 4 bolts and 2 rear differential bearing caps.

  1. C165859E01
    Using SST and a hammer, remove the 2 rear differential side gear shaft plate washers.
    SST
    09504-22011  

    HINT:
    Measure the thicknesses of the rear differential side gear shaft plate washers and note them down.

  1. C165860
    Remove the rear differential case and the 2 rear differential case bearing outer races from the differential carrier.

    HINT:
    Tag the 2 rear differential case bearing outer races to show the location for reassembly.


20. REMOVE DIFFERENTIAL DRIVE PINION
  1. Remove the differential drive pinion.


21. REMOVE REAR DRIVE PINION REAR TAPERED ROLLER BEARING

  1. C167100E01
    Using SST and a press, remove the rear drive pinion rear tapered roller bearing from the differential drive pinion.
    SST
    09950-00020  

    HINT:
    If either the differential drive pinion or differential ring gear is damaged, replace both as a set.

  1. Remove the rear differential drive pinion plate washer.


22. REMOVE REAR DRIVE PINION FRONT TAPERED ROLLER BEARING

  1. C120884E01
    Using a brass bar and a hammer, remove the rear drive pinion front tapered roller bearing (outer race) from the rear differential carrier sub-assembly.


23. REMOVE REAR DRIVE PINION REAR TAPERED ROLLER BEARING

  1. C120885E01
    Using a brass bar and a hammer, remove the rear drive pinion rear tapered roller bearing (outer race) from the rear differential carrier sub-assembly.


24. REMOVE DIFFERENTIAL RING GEAR

  1. C169429E01
    Put matchmarks on the differential ring gear and rear differential case.

  1. Using a screwdriver and a hammer, unstake the 4 rear differential ring gear set bolt lock plates.

  1. Remove the 8 bolts and 4 rear differential ring gear set bolt lock plates.


25. INSPECT RUNOUT OF REAR DIFFERENTIAL CASE

HINT:
Perform this procedure only if the runout of the differential ring gear exceeds the specified maximum value.

  1. C167101
    Install the rear differential case to the rear differential carrier sub-assembly.

  1. Install the right and left rear differential bearing caps with the 4 bolts.

    Torque:
    79 N*m{ 800 kgf*cm , 58 ft.*lbf }

  1. Using a dial indicator, measure the differential case runout.

    Maximum runout:
    0.07 mm (0.0028 in.)

    If the runout is greater than the maximum value, replace the differential case assembly with a new one.

  1. Remove the rear differential case.


26. REMOVE REAR DIFFERENTIAL CASE BEARING (for LH Side)

  1. C167103E01
    Using SST, remove the rear differential case bearing from the rear differential case.
    SST
    09950-40011   (09951-00240, 09951-04020, 09952-04010, 09953-04030, 09954-04010, 09955-04061, 09957-04010, 09958-04011)
    09950-60010   (09951-00360)


27. REMOVE REAR DIFFERENTIAL CASE BEARING (for RH Side)

  1. C167102E01
    Using SST, remove the rear differential case bearing (RH) from the rear differential case.
    SST
    09950-40011   (09951-04020, 09952-04010, 09953-04030, 09954-04010, 09955-04061, 09957-04010, 09958-04011)
    09950-60010   (09951-00360)


28. REMOVE REAR DIFFERENTIAL PINION SHAFT

  1. C167104
    Using a pin punch (5 mm) and a hammer, remove the rear differential pinion shaft straight pin.

  1. C169188E01
    Remove the rear differential pinion shaft. (A)

  1. Remove the 2 differential pinion gears. (B)

  1. Remove the 2 rear differential pinion thrust washers. (C)

  1. Remove the 2 differential side gears. (D)

  1. Remove the 2 No. 1 rear differential side gear thrust washers. (E)


29. INSPECT DIFFERENTIAL PINION AND SIDE GEAR
  1. Check that there is no damage to the differential pinion gears and side gears. If the differential pinion gears and/or side gears are damaged, replace them with new ones.


30. INSPECT REAR DIFFERENTIAL CASE
  1. Check that there is no damage to the differential case. If the differential case is damaged, replace it.

← REMOVAL (from Jul 2010)INSPECTION (from May 2007) →