2007-2013 Highlander Kluger · Service Manual DRIVE LINE

INSTALLATION

Removal / installation · Vehicles built from Jul 2010

Versions by build date: May 2007 – Jul 2008 Aug 2008 – Jun 2010 from Jul 2010


1. INSTALL REAR DIFFERENTIAL DRIVE PINION BEARING SPACER
  1. Install a new rear differential drive pinion bearing spacer.


2. INSTALL REAR DRIVE PINION FRONT TAPERED ROLLER BEARING
  1. Install the rear drive pinion front tapered roller bearing.


3. INSTALL REAR DIFFERENTIAL DRIVE PINION OIL SLINGER
  1. Install the differential drive pinion oil slinger.


4. INSTALL REAR DIFFERENTIAL CARRIER OIL SEAL

  1. C167087E01
    Using SST and a hammer, install a new rear differential carrier oil seal.
    SST
    09554-22010  

    Oil seal driven in depth:
    2.0 +/- 0.3 mm (0.079 +/- 0.012 in.)

  1. Coat the rear differential carrier oil seal lip with MP grease.


5. INSTALL REAR DRIVE PINION COMPANION FLANGE SUB-ASSEMBLY

  1. C167084E01
    Using SST, install the rear drive pinion companion flange sub-assembly on the shaft.
    SST
    09950-30012   (09951-03010, 09953-03010, 09954-03010, 09955-03030, 09956-03020)

    NOTICE:
    Apply hypoid gear oil to the SST center bolt tip and threads before use.


6. INSTALL REAR DRIVE PINION NUT
  1. Coat the threads of a new rear drive pinion nut with hypoid gear oil.

  1. C167082E01
    Using SST to hold the flange, tighten the rear drive pinion nut.
    SST
    09330-00021  

    Torque:
    108 N*m{ 1100 kgf*cm , 80 ft.*lbf }


7. INSPECT DIFFERENTIAL DRIVE PINION PRELOAD

  1. C171640
    Using a torque wrench, measure the preload of the drive pinon.

    Drive pinion preload (Initial):
    Item
    Preload
    New bearing
    1.1 to 1.7 N*m (11.2 to 17.3 kgf*cm, 9.7 to 15.0 in.*lbf)
    Reused bearing
    0.6 to 0.9 N*m (6.1 to 9.2 kgf*cm, 5.3 to 8.0 in.*lbf)

    1. If the preload is greater than the specification, replace the rear differential drive pinion bearing spacer.
    2. If the preload is less than the specification, replace the rear drive pinion nut and tighten it in several steps with 13 N*m (130 kgf*cm, 9 ft.*lbf) of torque at a time until the specified preload is reached.

    Torque:
    235 N*m (2400 kgf*cm, 174 ft.*lbf) or less

    1. If the torque exceeds the maximum while retightening the rear drive pinion nut, replace the rear differential drive pinion bearing spacer and repeat the preload adjusting procedure.

    NOTICE:
    Do not loosen the pinion nut to reduce the preload.


8. INSTALL REAR DRIVE PINION NUT

  1. C168606
    Using a chisel and hammer, stake the drive pinion nut.


9. TEMPORARILY TIGHTEN PROPELLER WITH CENTER BEARING SHAFT ASSEMBLY

  1. C166040E01
    Align the matchmarks on the propeller shaft flange and differential companion flange, and connect the shaft with the 4 bolts, 4 washers and 4 nuts.

  1. C166042E01
    Remove SST from the transaxle.

  1. Insert the yoke into the transaxle.

  1. C166041
    Install the 4 adjusting shims and propeller shaft with center bearing, and temporarily tighten the 4 bolts.

  1. C166040E01
    Tighten the 4 bolts.

    Torque:
    74 N*m{ 750 kgf*cm , 54 ft.*lbf }


10. FULLY TIGHTEN PROPELLER WITH CENTER BEARING SHAFT ASSEMBLY

  1. C167196
    Remove the piece of cloth from the joint.

  1. Using a hexagon wrench (6 mm), tighten the 6 bolts.

    Torque:
    26 N*m{ 265 kgf*cm , 19 ft.*lbf }

  1. C166068E01
    With the vehicle unloaded, adjust the dimension between the rear side of the cover and shaft as shown in the illustration.

    (A):
    58.0 +/- 0.5 mm (2.283 +/- 0.02 in.)

  1. Under the same condition as above, adjust the front and rear dimensions between the edge surface of the center support bearing and the edge surface of the cushion respectively as shown, and then tighten the bolts.

    C166069E01

    Torque:
    37 N*m{ 375 kgf*cm , 27 ft.*lbf }

    (B):
    12.5 +/- 1.0 mm (0.492 +/- 0.039 in.)

  1. Check that the center line of the bracket is at the right angle in the shaft axial direction.

  1. If any vibration or noise occurs, perform joint angle check as follows and replace the adjusting shim with a proper one.

    1. Turn the propeller shaft several times by hand to stabilize the center support bearings.

    2. Using a jack, raise and lower the differential to stabilize the differential mounting cushion.

    3. Remove the transfer dynamic damper.

    4. Using SST, measure the transfer installation angle (A) and front propeller shaft installation angle (B).

      SST
      09370-50010  

      No. 1 joint angle:
      (A) - (B) = -1.3° to -3.3°

    5. Using SST, measure the rear propeller shaft installation angle (C) and rear differential shaft installation angle (D).

      SST
      09370-50010  

      No. 2 joint angle:
      (C) - (D) = 1.8° to 3.5°


      C166070E01

      HINT:
      If the measured angle is not within the specification, adjust it with the center support bearing adjusting shim.

      Center support bearing adjusting shim thickness:
      Thickness mm (in.)
      Thickness mm (in.)
      3.2 (0.126)
      11.0 (0.433)
      4.5 (0.177)
      13.5 (0.531)
      6.5 (0.256)
      15.5 (0.610)
      9.0 (0.354)
      17.5 (0.689)

    6. Install the transfer dynamic damper.

      Torque:
      26 N*m{ 265 kgf*cm , 19 ft.*lbf }


11. INSTALL REAR DIFFERENTIAL DRAIN PLUG

  1. C166707
    Using a hexagon wrench (10 mm), install the drain plug with a new gasket.

    Torque:
    49 N*m{ 500 kgf*cm , 36 ft.*lbf }


12. ADD DIFFERENTIAL OIL
  1. Stop the vehicle on a level place.

  1. Remove the differential filler plug and gasket.

  1. C165855E01
    Check that the oil surface is within 5 mm (0.20 in.) of the lowest position of the inner surface of the differential filler plug opening.

    NOTICE:
    1. Excessively large or small amounts of oil may cause trouble.
    2. After replacing oil, drive the vehicle and check the oil level.

    HINT:
    If necessary, fill the rear differential carrier with hypoid gear oil.

    Oil grade:
    Hypoid gear oil API GL-5
    Recommended oil viscosity:
    Above -18°C (0°F) : SAE 90
    Below -18°C (0°F) : SAE 80W or 80W-90
    Capacity:
    0.9 +/- 0.05 liters (0.95 +/- 0.05 US qts, 0.79 +/- 0.04 lmp. qts)

  1. Check for oil leakage when the oil level is low.

  1. Install the differential filler plug and a new gasket.

    Torque:
    49 N*m{ 500 kgf*cm , 36 ft.*lbf }


13. INSPECT DIFFERENTIAL OIL
  1. Stop the vehicle on a level place.

  1. Remove the differential filler plug and gasket.

  1. C165855E01
    Check that the oil surface is within 5 mm (0.20 in.) of the lowest position of the inner surface of the differential filler plug opening.

    NOTICE:
    1. Excessively large or small amounts of oil may cause trouble.
    2. After replacing oil, drive the vehicle and check the oil level.

    HINT:
    If necessary, fill the rear differential carrier with hypoid gear oil.

    Oil grade:
    Hypoid gear oil API GL-5
    Recommended oil viscosity:
    Above -18°C (0°F) : SAE 90
    Below -18°C (0°F) : SAE 80W or 80W-90
    Capacity:
    0.9 +/- 0.05 liters (0.95 +/- 0.05 US qts, 0.79 +/- 0.04 lmp. qts)

  1. Check for oil leakage when the oil level is low.

  1. Install the differential filler plug and a new gasket.

    Torque:
    49 N*m{ 500 kgf*cm , 36 ft.*lbf }


14. INSTALL REAR DIFFERENTIAL FILLER PLUG

  1. C166706
    Using a hexagon wrench (10 mm), install the filler plug with a new gasket.

    Torque:
    49 N*m{ 500 kgf*cm , 36 ft.*lbf }


15. INSPECT AND ADJUST TRANSFER OIL

  1. C083746E03
    Remove the No. 1 transfer case plug and gasket.

  1. Check the oil level is within 0 to 5 mm (0 to 0.20 in.) below the lowest end of the hole for the No. 1 transfer case plug.

    NOTICE:
    1. When changing oil, recheck the oil level after driving.
    2. Excessively large or small quantity of oil may cause some trouble.

  1. When the oil level is too low, check for oil leakage.

  1. Tighten the No. 1 transfer case plug with a new gasket.

    Torque:
    49 N*m{ 500 kgf*cm , 36 ft.*lbf }

← INSTALLATION (Aug 2008 – Jun 2010)COMPONENTS (May 2007 – Jun 2010) →