2007-2013 Highlander Kluger · Service Manual ENGINE

INSTALLATION

Removal / installation · Vehicles built Aug 2008 – Jun 2010

Versions by build date: May 2007 – Jul 2008 Aug 2008 – Jun 2010 from Jul 2010


1. INSTALL AIR FUEL RATIO SENSOR NO.2 (for Bank 1 Sensor 1)

  1. A172496E01
    Using SST, install the air fuel ratio sensor to the exhaust manifold sub-assembly RH.
    SST
    09224-00010  

    Torque:
    40 N*m{ 408 kgf*cm , 30 ft.*lbf } for use with SST
    44 N*m{ 449 kgf*cm , 32 ft.*lbf } for use without SST

    HINT:
    1. Use a torque wrench with a fulcrum length of 30 cm (11.81 in.).
    2. Make sure that SST and the wrench are connected in a straight line.


2. INSTALL EXHAUST MANIFOLD SUB-ASSEMBLY RH
  1. Install a new gasket.

  1. A170131E01
    Install the exhaust manifold sub-assembly RH by tightening the 6 nuts in the order shown in the illustration.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }

  1. A171747
    Connect the air fuel ratio sensor (for bank 1 sensor 1) connector and install the clamp.


3. INSTALL MANIFOLD STAY

  1. A170128
    Install the manifold stay with the bolt and nut.

    Torque:
    Bolt:
    34 N*m{ 347 kgf*cm , 25 ft.*lbf }
    Nut:
    35 N*m{ 357 kgf*cm , 26 ft.*lbf }


4. INSTALL FRONT NO. 3 EXHAUST PIPE SUB-ASSEMBLY

  1. A170126
    Install 2 new gaskets to the front No. 3 exhaust pipe sub-assembly.

  1. Install the front No. 3 exhaust pipe sub-assembly with 2 new nuts and the 2 bolts.

    Torque:
    56 N*m{ 571 kgf*cm , 41 ft.*lbf }

  1. A171743
    Install the 3 clamps and connect the heated oxygen sensor (for bank 1 sensor 2) connector.

  1. A170135
    Tighten the front exhaust pipe assembly bolt.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }


5. INSTALL CENTER EXHAUST PIPE ASSEMBLY

  1. A160224
    Using vernier calipers, measure the free length of the compression spring.
    Minimum
    41.5 mm (1.63 in.)

    HINT:
    If the length is less than the minimum, replace the compression spring.

  1. A138040E01
    Using a plastic-faced hammer and wooden block, tap in a new gasket until its surface is flush with the front No. 3 exhaust pipe sub-assembly.

    NOTICE:
    1. Tap in the gasket in the correct direction.
    2. Do not reuse the removed gasket.
    3. Do not push in the gasket while installing the center exhaust pipe assembly.

  1. Connect the 3 exhaust pipe supports, and install the center exhaust pipe assembly.

  1. A170125
    Install the 2 compression springs and 2 bolts.

    Torque:
    48 N*m{ 489 kgf*cm , 35 ft.*lbf }


6. INSTALL TAIL EXHAUST PIPE ASSEMBLY

  1. A160224
    Using vernier calipers, measure the free length of the compression spring.
    Minimum
    40.5 mm (1.59 in.)

    HINT:
    If the length is less than the minimum, replace the compression spring.

  1. A138040E01
    Using a plastic-faced hammer and wooden block, tap in a new gasket until its surface is flush with the center exhaust pipe assembly.

    NOTICE:
    1. Tap in the gasket in the correct direction.
    2. Do not reuse the removed gasket.
    3. Do not push in the gasket while installing the tail exhaust pipe assembly.

  1. Connect the exhaust pipe support, and install the tail exhaust pipe assembly.

  1. A170139
    Install the 2 compression springs and 2 bolts.

    Torque:
    48 N*m{ 489 kgf*cm , 35 ft.*lbf }


7. TEMPORARILY TIGHTEN PROPELLER WITH CENTER BEARING SHAFT ASSEMBLY (for 4WD)

  1. C166040E01
    Align the matchmarks on the propeller shaft flange and differential companion flange, and connect the shaft with the 4 bolts, 4 washers and 4 nuts.

  1. C166042E01
    Remove SST from the transaxle.

  1. Insert the yoke into the transaxle.

  1. C166041
    Install the 4 adjusting shims and propeller shaft with center bearing, and temporarily tighten the 4 bolts.

  1. C166040E01
    Tighten the 4 bolts.

    Torque:
    74 N*m{ 750 kgf*cm , 54 ft.*lbf }


8. FULLY TIGHTEN PROPELLER WITH CENTER BEARING SHAFT ASSEMBLY (for 4WD)

  1. C167196
    Remove the piece of cloth from the joint.

  1. Using a hexagon wrench (6 mm), tighten the 6 bolts.

    Torque:
    26 N*m{ 265 kgf*cm , 19 ft.*lbf }

  1. C166068E01
    With the vehicle unloaded, adjust the dimension between the rear side of the cover and shaft as shown in the illustration.

    (A):
    58.0 +/- 0.5 mm (2.283 +/- 0.02 in.)

  1. Under the same condition as above, adjust the front and rear dimensions between the edge surface of the center support bearing and the edge surface of the cushion respectively as shown, and then tighten the bolts.

    C166069E01

    Torque:
    37 N*m{ 375 kgf*cm , 27 ft.*lbf }

    (B):
    12.5 +/- 1.0 mm (0.492 +/- 0.039 in.)

  1. Check that the center line of the bracket is at the right angle in the shaft axial direction.

  1. If any vibration or noise occurs, perform joint angle check as follows and replace the adjusting shim with a proper one.

    1. Turn the propeller shaft several times by hand to stabilize the center support bearings.

    2. Using a jack, raise and lower the differential to stabilize the differential mounting cushion.

    3. Remove the transfer dynamic damper.

    4. Using SST, measure the transfer installation angle (A) and front propeller shaft installation angle (B).

      SST
      09370-50010  

      No. 1 joint angle:
      (A) - (B) = -1.3° to -3.3°

    5. Using SST, measure the rear propeller shaft installation angle (C) and rear differential shaft installation angle (D).

      SST
      09370-50010  

      No. 2 joint angle:
      (C) - (D) = 1.8° to 3.5°


      C166070E01

      HINT:
      If the measured angle is not within the specification, adjust it with the center support bearing adjusting shim.

      Center support bearing adjusting shim thickness:
      Thickness mm (in.)
      Thickness mm (in.)
      3.2 (0.126)
      11.0 (0.433)
      4.5 (0.177)
      13.5 (0.531)
      6.5 (0.256)
      15.5 (0.610)
      9.0 (0.354)
      17.5 (0.689)

    6. Install the transfer dynamic damper.

      Torque:
      26 N*m{ 265 kgf*cm , 19 ft.*lbf }


9. INSPECT FOR EXHAUST GAS LEAK
If exhaust gas is leaking, repair the leak. Replace damaged or worn parts as necessary.

10. INSPECT AND ADJUST TRANSFER OIL (for 4WD)

HINT:
Click here


11. INSTALL FRONT FLOOR COVER LH

  1. A171744
    Install the 3 clamps, 6 bolts and the front floor cover LH.


12. INSTALL NO. 2 ENGINE UNDER COVER

  1. A171854
    Install the No. 2 engine under cover with the 2 bolts.


13. INSTALL NO. 1 ENGINE UNDER COVER

  1. A171855
    Install the No. 1 engine under cover with the 6 bolts and 2 clips.


14. INSTALL ENGINE UNDER COVER ASSEMBLY

  1. A171850
    Install the engine under cover assembly with the 2 bolts, 2 screws and 5 clips.

  1. A171849
    Install the engine under cover assembly RR with the 2 bolts.


15. INSTALL AIR FUEL RATIO SENSOR (for Bank 2 Sensor 1)

  1. A171728
    Using SST, install the air fuel ratio sensor to the exhaust manifold sub-assembly LH.
    SST
    09224-00010  

    Torque:
    40 N*m{ 408 kgf*cm , 30 ft.*lbf } for use with SST
    44 N*m{ 449 kgf*cm , 32 ft.*lbf } for use without SST

    HINT:
    1. Use a torque wrench with a fulcrum length of 30 cm (11.81 in.).
    2. Make sure that SST and the wrench are connected in a straight line.

  1. A171746
    Connect the air fuel ratio sensor connector and install the clamp.

← INSTALLATION (May 2007 – Jul 2008)INSTALLATION (from Jul 2010) →