2007-2013 Highlander Kluger · Service Manual STEERING

REMOVAL

Removal / installation · Vehicles built Jul 2010 – Jun 2012

Versions by build date: May 2007 – Jul 2008 Aug 2008 – Jun 2010 Jul 2010 – Jun 2012 Jul 2012 – Jul 2013 from Aug 2013


1. DISCHARGE FUEL SYSTEM PRESSURE

HINT:
Click here.


2. RECOVER REFRIGERANT FROM REFRIGERATION SYSTEM
  1. Start the engine.

  1. Turn the A/C switch on.

  1. Operate the cooler compressor at an engine speed of approximately 1000 rpm for 5 to 6 minutes to circulate the refrigerant. This causes most of the compressor oil from the various components of the A/C system to collect in the A/C compressor.

  1. Stop the engine.

  1. Recover the refrigerant from the A/C system using a refrigerant recovery unit.


3. REMOVE COOL AIR INTAKE DUCT SEAL

  1. A170196
    Remove the 11 clips and cool air intake duct seal.


4. REMOVE BATTERY

  1. A171858
    Loosen the nut, and disconnect the negative battery terminal.

    CAUTION:
    Wait for 90 seconds after disconnecting the cable to prevent the airbag working.

    NOTICE:
    When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).

  1. Remove the nut, and separate the positive battery terminal cable.

  1. Loosen the nut, and remove the bolt and battery clamp.

  1. Remove the battery and battery tray.


5. PLACE FRONT WHEELS FACING STRAIGHT AHEAD

6. SECURE STEERING WHEEL

  1. C165552
    Secure the steering wheel with the seat belt in order to prevent it from rotating.

    HINT:
    This operation is necessary to prevent damage to the spiral cable.


7. REMOVE FRONT WHEELS

8. REMOVE ENGINE UNDER COVER ASSEMBLY

  1. A171849
    Remove the 2 bolts and engine under cover assembly RR.

  1. A171850
    Remove the 2 bolts, 2 screws, 5 clips and engine under cover assembly.


9. REMOVE NO. 1 ENGINE UNDER COVER

  1. A237657
    Remove the 6 bolts, 2 clips and No. 1 engine under cover.


10. REMOVE NO. 2 ENGINE UNDER COVER

  1. A171854
    Remove the 2 bolts and No. 2 engine under cover.


11. REMOVE FLOOR UNDER COVER LH

  1. A171744
    Remove the 3 clamps, 6 bolts and front floor cover LH.


12. REMOVE FRONT FENDER MOULDING SUB-ASSEMBLY LH

  1. B172795
    Remove the clip.

  1. Using a 4 mm hexagon wrench, remove the screw.

  1. B172796
    Peel off the double-sided tape and disengage the 3 clips, and then remove the front fender moulding sub-assembly.

  1. Remove the pad from the front fender moulding sub-assembly.

  1. Remove the 2 No. 4 clips from the front fender moulding sub-assembly.

  1. B172797E02
    Remove the double-sided tape from the front fender moulding sub-assembly.
    Text in Illustration 
    *1
    Double-sided Tape


13. REMOVE FRONT FENDER MOULDING SUB-ASSEMBLY RH

HINT:
Use the same procedure as for the LH side.


14. REMOVE FRONT FENDER LINER LH

  1. B258289E01
    Remove the screw.

  1. Using a screwdriver, turn the pin 90 degrees and remove the 2 pin hold clips.

  1. B260029
    Using a 4 mm hexagon wrench, remove the 2 screws.

  1. Remove the 3 grommets.

    HINT:
    The grommets need to be replaced with new ones because they will break when they are removed.

  1. B260027
    Remove the 5 clips.

  1. Remove the bolt, 8 screws and front fender liner LH.


15. REMOVE FRONT FENDER LINER RH

  1. B258290E01
    Remove the screw.

  1. Using a screwdriver, turn the pin 90 degrees and remove the 2 pin hold clips.

  1. B260030
    Using a 4 mm hexagon wrench, remove the 2 screws.

  1. Remove the 3 grommets.

    HINT:
    The grommets need to be replaced with new ones because they will break when they are removed.

  1. B260028
    Remove the 5 clips

  1. Remove the bolt, 8 screws and front fender liner RH.


16. REMOVE FRONT FENDER APRON SEAL LH

  1. A171852
    Remove the 2 bolts, clip and front fender apron seal LH.


17. REMOVE FRONT FENDER APRON SEAL RH

  1. A171853
    Remove the 2 bolts, clip and front fender apron seal RH.


18. DRAIN ENGINE OIL
  1. Remove the oil filler cap.

  1. Remove the oil drain plug and gasket, and drain the oil into a container.

  1. Clean and install the oil drain plug with a new gasket.

    Torque:
    40 N*m{ 408 kgf*cm , 30 ft.*lbf }


19. DRAIN ENGINE COOLANT

  1. Loosen the radiator drain cock plug.

    A169414E01

    HINT:
    Collect the coolant in a container and dispose of it according to the regulations in your area.

  1. Remove the radiator cap sub-assembly from the radiator assembly.

    NOTICE:
    Do not remove the radiator cap sub-assembly while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.

  1. Loosen the 2 cylinder block drain cock plugs.


20. DRAIN AUTOMATIC TRANSAXLE FLUID
  1. Remove the drain plug and gasket, and drain ATF.

  1. Install a new gasket and the drain plug.

    Torque:
    49 N*m{ 500 kgf*cm , 36 ft.*lbf }


21. REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY RH

  1. E150145
    Remove the nut, and the front wiper arm and blade assembly RH.


22. REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY LH

  1. E150144
    Remove the nut, and the front wiper arm and blade assembly LH.


23. REMOVE COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY

  1. E150146
    Disengage the 2 claws and disconnect the front fender to cowl side seal LH.

  1. E150147
    Disengage the 2 claws and disconnect the front fender to cowl side seal RH.

  1. Remove the 2 clips.

    E150149

  1. Disengage the 20 claws and remove the cowl top ventilator louver sub-assembly.


24. REMOVE WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY

  1. E150150
    Disconnect the connector.

  1. Remove the 4 bolts, and the windshield wiper motor and link assembly.


25. REMOVE OUTER COWL TOP PANEL SUB-ASSEMBLY (for LHD)

  1. A173038
    Remove the 4 clips, and separate the engine wire.

  1. Remove the 8 bolts, 6 nuts and front outer cowl top panel sub-assembly.

    A171889


26. REMOVE OUTER COWL TOP PANEL SUB-ASSEMBLY (for RHD)

  1. A173037
    Remove the 4 clips, and separate the engine wire.

  1. Remove the 8 bolts, 6 nuts and front outer cowl top panel sub-assembly.

    A171889


27. REMOVE V-BANK COVER SUB-ASSEMBLY

  1. A162365
    Hold the front of the V-bank cover sub-assembly and raise it to disengage the 2 clips on the front of the V-bank cover sub-assembly. Continue rising the V-bank cover sub-assembly to disengage the clip on the rear of the V-bank cover sub-assembly and remove the V-bank cover sub-assembly.

    NOTICE:
    Attempting to disengage both front and rear clips at the same time may cause the V-bank cover sub-assembly to break.


28. REMOVE NO. 2 AIR CLEANER INLET

  1. A170453
    Disconnect the 2 vacuum switching valve clamps.

  1. Disconnect the 2 vacuum hoses.

  1. Remove the 2 bolts and No. 2 air cleaner inlet.


29. REMOVE NO. 1 AIR CLEANER INLET

  1. A170454
    Disconnect the 2 vacuum hoses, and remove the 2 bolts and No. 1 air cleaner inlet.


30. REMOVE AIR CLEANER CAP SUB-ASSEMBLY

  1. A170887
    Disconnect the 3 vacuum hoses.

  1. A170447
    Loosen the No. 1 air cleaner hose clamp.

  1. Disconnect the hose clamps and No. 2 ventilation hose.

  1. Disconnect the mass air flow meter connector.

  1. A170451
    Release the 2 clips, and remove the 2 bolts.

  1. Remove the air cleaner cap sub-assembly and air cleaner filter element.


31. REMOVE AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY
  1. Remove the air cleaner filter element sub-assembly.


32. REMOVE AIR CLEANER CASE SUB-ASSEMBLY

  1. A170450
    Remove the 3 bolts, disconnect the hose and the connector, and remove the air cleaner case sub-assembly.


33. REMOVE AIR CLEANER BRACKET

  1. A171820
    Remove the 2 bolts and air cleaner bracket.


34. SEPARATE BRAKE MASTER CYLINDER RESERVOIR ASSEMBLY (for LHD)

  1. A171831
    Disconnect the level warning switch connector.

  1. Remove the bolt, and separate the brake master cylinder reservoir assembly.


35. REMOVE RESERVOIR BRACKET (for LHD)

  1. A171859
    Remove the 2 bolts and reservoir bracket.


36. SEPARATE BRAKE MASTER CYLINDER RESERVOIR ASSEMBLY (for RHD)

  1. A171878
    Disconnect the level warning switch connector.

  1. Remove the bolt, and separate the brake master cylinder reservoir assembly.


37. REMOVE RESERVOIR BRACKET (for RHD)

  1. A171879
    Remove the 2 bolts and reservoir bracket.


38. REMOVE NO. 2 ENGINE MOUNTING STAY RH

  1. A139217
    Remove the bolt, 2 nuts and No. 2 engine mounting stay RH.


39. REMOVE ENGINE MOVING CONTROL ROD

  1. A171824
    Remove the 3 bolts and engine moving control rod.


40. DISCONNECT NO. 1 FUEL VAPOR FEED HOSE

  1. A171821
    Slide the clamp and disconnect the No. 1 fuel vapor feed hose.


41. DISCONNECT NO. 1 RADIATOR HOSE

  1. A171822
    Disconnect the clamp.

  1. Using pliers, grip the claws of the clip and slide the clip to disconnect the No. 1 radiator hose from the water outlet.


42. DISCONNECT NO. 2 RADIATOR HOSE

  1. A171823
    Using pliers, grip the claws of the clip and slide the clip to disconnect the No. 2 radiator hose from the water inlet.


43. DISCONNECT HEATER WATER HOSE OUTLET B

  1. A171825
    Using pliers, grip the claws of the clip and slide the clip to disconnect heater water outlet hose B from the water inlet.


44. DISCONNECT HEATER WATER HOSE INLET B

  1. A171826
    Using pliers, grip the claws of the clip and slide the clip to disconnect heater water inlet hose B from the water outlet.


45. DISCONNECT FUEL TUBE SUB-ASSEMBLY

  1. A171827
    Remove the No. 1 fuel pipe clamp.

  1. B012941E15
    Disconnect the fuel tube from the fuel pipe pinching part A with your fingers as shown in the illustration.

    NOTICE:
    1. Check for dirt and foreign objects on the pipe and around the connector. Clean if necessary and then disconnect the connector.
    2. Disconnect the connector by hand.
    3. Do not bend, fold or rotate the nylon tube.
    4. If the pipe and connector are stuck together, push and pull the connector until it becomes free.
    5. Put the pipe and connector ends in plastic bags to prevent damage and contamination.


46. DISCONNECT OIL COOLER INLET HOSE

  1. A171828
    Using pliers, grip the claws of the clip and slide the clip to disconnect the No. 2 transmission oil cooler hose.


47. DISCONNECT OIL COOLER OUTLET HOSE

  1. A171829
    Using pliers, grip the claws of the clip and slide the clip to disconnect the oil cooler outlet hose.


48. DISCONNECT TRANSMISSION CONTROL CABLE ASSEMBLY

  1. D025414E11
    Remove the nut from the control shaft lever.

  1. Disconnect the transmission control cable assembly from the control shaft lever.

  1. C089134E04
    Remove the clip and disconnect the transmission control cable assembly from the control cable bracket.

  1. C090579
    Disconnect the transmission control cable assembly from the control cable clamp.


49. DISCONNECT ENGINE WIRE (for LHD)

  1. Disconnect the engine wire from the engine room relay block.

    1. Remove the No. 1 relay block cover.

    2. A171851
      Remove the nut.

    3. Disconnect the engine wire connector from the engine room relay block.

    4. Unlock the engine wire. Pull the engine room wire.

  1. A173068
    Disconnect the engine wire clamp.

  1. A173069
    Remove the bolt, and separate the ground cables.

  1. A171886
    Disconnect the heated oxygen sensor connector and clamp.

  1. A173070
    Remove the 2 bolts and 2 ground cables.

  1. A171880
    Disconnect the 3 ECM connectors, 2 junction block connectors and clamp.

  1. A171861
    Remove the 2 nuts and clamp, and separate the engine wire from the body.


50. DISCONNECT ENGINE WIRE (for RHD)

  1. Disconnect the engine wire from the engine room relay block.

    1. Remove the No. 1 relay block cover.

    2. A171851
      Remove the nut.

    3. Disconnect the engine wire connector from the engine room relay block.

    4. Unlock the engine wire. Pull the engine room wire.

  1. A173068
    Disconnect the engine wire clamp.

  1. A173069
    Remove the bolt, and separate the ground cables.

  1. A171886
    Disconnect the heated oxygen sensor connector and clamp.

  1. A173070
    Remove the 2 bolts and 2 ground cables.

  1. A173039
    Disconnect the 3 ECM connectors, 2 junction block connectors and clamp.

  1. A171881
    Remove the 2 nuts and clamp, and separate the engine wire from the body.


51. DISCONNECT UNION TO CHECK VALVE HOSE

  1. A162374
    Using pliers, grip the claws of the clip and slide the clip to disconnect the union to check valve hose.


52. REMOVE PROPELLER WITH CENTER BEARING SHAFT ASSEMBLY (for 4WD)

  1. C166039
    Depress the brake pedal and hold it.

  1. Using a hexagon wrench (6 mm), loosen the cross groove joint set bolts 1/2 turn.

    HINT:
    Put a piece of cloth or equivalent into the inside of the universal joint cover so that the boot does not touch the inside of the universal joint cover.

  1. C166040E01
    Place matchmarks on the rear propeller shaft and rear drive pinion flange sub-assembly.

  1. Remove the 4 nuts, 4 bolts and 4 washers.

  1. C166041
    Remove the 4 bolts and 4 adjusting shims.

  1. C166073
    Using a brass bar and a hammer, remove the propeller shaft with center bearing shaft assembly.

  1. C166042E01
    Insert SST into the transfer to prevent oil leakage.
    SST
    09325-20010  


53. REMOVE TAIL EXHAUST PIPE ASSEMBLY

  1. A170139
    Remove the 2 bolts and 2 compression springs.

  1. Disconnect the exhaust pipe support and remove the tail exhaust pipe assembly.

  1. Remove the gasket from the center exhaust pipe assembly.


54. REMOVE CENTER EXHAUST PIPE ASSEMBLY

  1. A170125
    Remove the 2 bolts and 2 compression springs.

  1. Disconnect the 3 exhaust pipe supports and remove the center exhaust pipe assembly.

  1. Remove the gasket from the No. 3 exhaust pipe sub-assembly.


55. REMOVE FRONT NO. 3 EXHAUST PIPE SUB-ASSEMBLY

  1. A171743
    Remove the 3 clamps and disconnect the heated oxygen sensor (for bank 1 sensor 2) connector.

  1. A170126
    Remove the 2 bolts, 2 nuts and front No. 3 exhaust pipe sub-assembly.

  1. Remove the 2 gaskets from the front No. 3 exhaust pipe sub-assembly.


56. REMOVE FRONT EXHAUST PIPE ASSEMBLY

  1. A170127
    Loosen the bolt.

  1. Remove the 2 nuts and front exhaust pipe assembly.

  1. Remove the gasket from the front exhaust pipe assembly.


57. SEPARATE FRONT STABILIZER LINK ASSEMBLY LH

  1. C165915
    Remove the nut and separate the front stabilizer link assembly from the front shock absorber.

    HINT:
    If the ball joint turns together with the nut, use a hexagon wrench (6 mm) to hold the stud.


58. SEPARATE FRONT STABILIZER LINK ASSEMBLY RH

HINT:
Perform the same procedure as for the LH side.


59. REMOVE FRONT AXLE HUB NUT LH

  1. C167528E01
    Using SST and a hammer, release the staked part of the front axle hub nut.
    SST
    09930-00010  

    NOTICE:
    Loosen the staked part of the nut completely, otherwise the threads of the drive shaft may be damaged.

  1. While applying the brakes, remove the front axle hub nut.


60. REMOVE FRONT AXLE HUB NUT RH

HINT:
Perform the same procedure as for the LH side.


61. SEPARATE FRONT SPEED SENSOR LH

  1. C165818E03
    Remove the bolt and resin clamp, and separate the front speed sensor.


62. SEPARATE FRONT SPEED SENSOR RH

HINT:
Perform the same procedure as for the LH side.


63. SEPARATE STEERING INTERMEDIATE SHAFT ASSEMBLY

  1. C165544
    Remove the bolt and slide the steering intermediate shaft assembly.

    NOTICE:
    Do not separate the steering intermediate shaft assembly from the power steering link assembly.

  1. C165545E01
    Put matchmarks on the steering intermediate shaft assembly and the power steering link assembly.

  1. Separate the steering intermediate shaft assembly from the power steering link assembly.


64. SEPARATE TIE ROD ASSEMBLY LH
  1. Remove the cotter pin and the nut.

  1. C165542E01
    Install SST to the tie rod end.
    SST
    09960-20010   (09961-02060)

    NOTICE:
    Make sure that the upper ends of the tie rod end and SST are aligned.

  1. Using SST, separate the tie rod end from the steering knuckle.

    C165543E01

    SST
    09960-20010   (09961-02010)

    NOTICE:
    1. When securing SST to the steering knuckle, be sure to tighten the string of SST to prevent it from falling.
    1. Install SST so that A and B are parallel.
    1. Be sure to place the wrench on the part indicated in the illustration.
    1. Do not damage the front disc brake dust cover.
    1. Do not damage the ball joint dust cover.
    1. Do not damage the steering knuckle.


65. SEPARATE TIE ROD ASSEMBLY RH

HINT:
Perform the same procedure as for the LH side.


66. SEPARATE NO. 1 FRONT SUSPENSION LOWER ARM LH

  1. C165929
    Remove the bolt and 2 nuts, and separate the front lower suspension arm from the front lower ball joint.


67. SEPARATE NO. 1 FRONT SUSPENSION LOWER ARM RH

HINT:
Perform the same procedure as for the LH side.


68. SEPARATE FRONT AXLE ASSEMBLY LH

  1. C165537E04
    Put matchmarks on the front drive shaft assembly and the front axle hub sub-assembly.

  1. C165534
    Using a plastic hammer, separate the front drive shaft assembly from the front axle assembly.

    NOTICE:
    Loosen the staked part of the front axle hub nut completely, otherwise the threads of the drive shaft may be damaged.


69. SEPARATE FRONT AXLE ASSEMBLY RH

HINT:
Perform the same procedure as for the LH side.


70. DISCONNECT DISCHARGE HOSE SUB-ASSEMBLY

  1. E212986
    Remove the bolt and disconnect the discharge hose sub-assembly from the compressor and magnetic clutch.

  1. Remove the O-ring from the discharge hose sub-assembly.

    NOTICE:
    Seal the openings of the disconnected parts using vinyl tape to prevent entry of moisture and foreign matter.


71. DISCONNECT SUCTION HOSE SUB-ASSEMBLY

  1. E212987
    Remove the bolt and disconnect the suction hose sub-assembly from the compressor and magnetic clutch.

  1. Remove the O-ring from the suction hose sub-assembly.

    NOTICE:
    Seal the openings of the disconnected parts using vinyl tape to prevent entry of moisture and foreign matter.


72. REMOVE ENGINE ASSEMBLY WITH TRANSAXLE
  1. Set the engine lifter.

  1. A171833
    Remove the 6 bolts, 2 nuts, and frame side rail plates RH and LH.

  1. A171834
    Remove the 6 bolts, 2 nuts, and front suspension member rear braces RH and LH.

  1. Operate the engine lifter, then remove the engine assembly from the vehicle.

    NOTICE:
    Make sure that the engine is clear of all wiring and hoses.


73. REMOVE FRONT NO. 1 STABILIZER BRACKET LH

  1. C167140
    Remove the 2 bolts and the No. 1 front stabilizer bracket LH from the front frame assembly.


74. REMOVE FRONT NO. 1 STABILIZER BRACKET RH

HINT:
Perform the same procedure as the LH side.


75. REMOVE FRONT STABILIZER BAR

76. REMOVE POWER STEERING LINK ASSEMBLY

  1. C166343
    Remove the 2 bolts, 2 nuts, and power steering link assembly.

    NOTICE:
    Because the nut has its own stopper, do not turn the nut. Loosen the bolt with the nut fixed.


77. REMOVE TIE ROD ASSEMBLY LH

  1. C165553E01
    Put matchmarks on the tie rod assembly LH and the steering rack end sub-assembly.

  1. Loosen the lock nut, and remove the tie rod assembly LH and the lock nut.


78. REMOVE TIE ROD ASSEMBLY RH

HINT:
Perform the same procedure as for the LH side.

← REMOVAL (Aug 2008 – Jun 2010)REMOVAL (Jul 2012 – Jul 2013) →