2007-2013 Highlander Kluger · Service Manual BODY ELECTRICAL

No Answer-Back

Circuit diagnosis · Vehicles built Aug 2008 – Jun 2010

Versions by build date: May 2007 – Jul 2008 Aug 2008 – Jun 2010 from Jul 2010

DESCRIPTION

In some cases, wireless door lock control functions are normal but the hazard warning lights and/or wireless door lock buzzer answer-back function(s) do not operate. In such cases, the main body ECU's hazard warning lights and wireless door lock buzzer signal outputs may be malfunctioning.

NOTICE:
Troubleshooting should be started after confirming that the customize status of the answer-back function has been switched ON.


WIRING DIAGRAM

B175278E03

INSPECTION PROCEDURE


1. READ VALUE USING INTELLIGENT TESTER (DOOR LOCK POSITION SWITCH)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to the ON position.

  1. Turn the intelligent tester on.

  1. Enter the following menus: Body / Main Body / Data List.

  1. Read the Data List according to the display on the intelligent tester.

    Main Body (Main Body ECU (Instrument Panel Junction Block)) 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    D-Door Lock Pos SW
    Driver door lock position switch signal/LOCK or UNLOCK
    ON: Driver side door is unlocked
    OFF: Driver side door is locked
    -
    P-Door Lock Pos SW
    Front passenger side door lock position switch signal/ON or OFF
    ON: Front passenger side door is unlocked
    OFF: Front passenger side door is locked
    -
    RR-Door Lock Pos SW
    Rear right side door lock position switch signal/ON or OFF
    ON: Rear right side door unlocked
    OFF: Rear right side door locked
    -
    RL-Door Lock Pos SW
    Rear left side door lock position switch signal/ON or OFF
    ON: Rear left side door unlocked
    OFF: Rear left side door locked
    -

    OK:
    On the intelligent tester screen, the display changes between ON and OFF as shown in the chart above.


    Result:
    Result
    Proceed to
    OK
    A
    NG (for Driver Side)
    B
    (Proceed to "Driver Door LOCK/UNLOCK Functions do not Operate")
    NG (for Front Passenger Side)
    C
    (Proceed to "Front Passenger Door LOCK/UNLOCK Functions do not Operate")
    NG (for Rear LH Side)
    D
    (Proceed to "Rear Door LH LOCK/UNLOCK Functions do not Operate")
    NG (for Rear RH Side)
    E
    (Proceed to "Rear Door RH LOCK/UNLOCK Functions do not Operate")



B
GO TO POWER DOOR LOCK CONTROL SYSTEM (Click here)

C
GO TO POWER DOOR LOCK CONTROL SYSTEM (Click here)

D
GO TO POWER DOOR LOCK CONTROL SYSTEM (Click here)

E
GO TO POWER DOOR LOCK CONTROL SYSTEM (Click here)
A


2. CHECK WIRELESS DOOR LOCK CONTROL FUNCTION
  1. Check the wireless door lock control functions by operating the transmitter switch.

    Result:
    Result
    Proceed to
    Wireless door lock functions are normal but hazard warning lights answer-back does not occur
    A
    Wireless door lock functions are normal but wireless door lock buzzer answer-back does not occur*
    B
    Doors cannot be locked and unlocked with transmitter
    C

    HINT:
    *: for RHD



B
Go to step 5

C
GO TO PROBLEM SYMPTOMS TABLE (Click here)
A


3. CHECK HAZARD WARNING LIGHT
  1. Check that the hazard warning lights flash continuously when the hazard warning signal switch is pressed.

    OK:
    Hazard warning lights flash continuously.



NG
GO TO LIGHTING SYSTEM (Click here)
OK


4. PERFORM ACTIVE TEST USING INTELLIGENT TESTER (FLASHER RELAY)
  1. Select an Active Test, use the intelligent tester to generate a control command, and then check that the hazard warning lights flash.

    Main Body ECU 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Hazard
    Turn Signal Flasher
    ON/OFF
    -

    OK:
    Hazard warning lights are turned ON/OFF.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE MAIN BODY ECU

5. PERFORM ACTIVE TEST USING INTELLIGENT TESTER (WIRELESS DOOR LOCK BUZZER)
  1. Select the Active Test, use the intelligent tester to generate a control command, and then check that the wireless buzzer operate normally.

    Main Body ECU 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Wireless Buzzer
    wireless door lock buzzer
    ON/OFF
    -

    OK:
    Wireless buzzer turns ON/OFF.



NG
Go to step 6
OK

REPLACE MAIN BODY ECU

6. INSPECT WIRELESS DOOR LOCK BUZZER
B170058E06
  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    Always
    950 to 1050 Ω

    NOTICE:
    1. The buzzer circuit is built into the main body ECU, not into the buzzer itself.
    2. When battery voltage is directly applied to the buzzer, the buzzer does not sound.



NG
REPLACE WIRELESS DOOR LOCK BUZZER (Click here)
OK


7. CHECK HARNESS AND CONNECTOR (WIRELESS DOOR LOCK BUZZER - MAIN BODY ECU AND BODY GROUND)
B176366E04
  1. Disconnect the A13 wireless door lock buzzer connector.

  1. Disconnect the D9 main body ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    A13-1 - D9-7 (BZR)
    Always
    Below 1 Ω
    A13-2 - Body ground
    Always
    A13-1 or D9-7 (BZR) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE MAIN BODY ECU


← No Answer-Back (May 2007 – Jul 2008)No Answer-Back (from Jul 2010) →