INSTALLATION
Removal / installation · Vehicles built from Jul 2010
Versions by build date: May 2007 – Jul 2008 Aug 2008 – Jun 2010 from Jul 2010
| 1.
INSTALL HEATED OXYGEN SENSOR (for Bank 2 Sensor 2)
|
 |
- Using SST, install the heated oxygen sensor to the front exhaust pipe assembly.
- SST
- 09224-00010
-
Torque:
- 40 N*m{
408 kgf*cm
, 30 ft.*lbf
}
for use with SST
- 44 N*m{
449 kgf*cm
, 32 ft.*lbf
}
for use without SST
- HINT:
- Use a torque wrench with a fulcrum length of 30 cm (11.81 in.).
- Make sure that SST and the wrench are connected in a straight line.
| 2.
INSTALL FRONT EXHAUST PIPE ASSEMBLY |
 |
- Install a new gasket to the front exhaust pipe assembly.
Install the front exhaust pipe assembly with 2 new nuts.
-
Torque:
- 56 N*m{
571 kgf*cm
, 41 ft.*lbf
}
- Connect the heated oxygen sensor (for bank 2 sensor 2) connector.
| 3.
INSTALL HEATED OXYGEN SENSOR (for Bank 1 Sensor 2)
|
 |
- Using SST, install the heated oxygen sensor to the front No. 3 exhaust pipe sub-assembly.
- SST
- 09224-00010
-
Torque:
- 40 N*m{
408 kgf*cm
, 30 ft.*lbf
}
for use with SST
- 44 N*m{
449 kgf*cm
, 32 ft.*lbf
}
for use without SST
- HINT:
- Use a torque wrench with a fulcrum length of 30 cm (11.81 in.).
- Make sure that SST and the wrench are connected in a straight line.
| 4.
INSTALL FRONT NO. 3 EXHAUST PIPE SUB-ASSEMBLY |
 |
- Install 2 new gaskets to the front No. 3 exhaust pipe sub-assembly.
Install the front No. 3 exhaust pipe sub-assembly with 2 new nuts and the 2 bolts.
-
Torque:
- 56 N*m{
571 kgf*cm
, 41 ft.*lbf
}
- Install the 3 clamps and connect the heated oxygen sensor (for bank 1 sensor 2) connector.
- Tighten the front exhaust pipe assembly bolt.
-
Torque:
- 21 N*m{
214 kgf*cm
, 15 ft.*lbf
}
| 5.
INSTALL CENTER EXHAUST PIPE ASSEMBLY |
 |
- Using vernier calipers, measure the free length of the compression spring.
Minimum
|
41.5 mm (1.63 in.)
|
- HINT:
- If the length is less than the minimum, replace the compression spring.
- Using a plastic-faced hammer and wooden block, tap in a new gasket until its surface is flush with the front No. 3 exhaust pipe sub-assembly.
- NOTICE:
- Tap in the gasket in the correct direction.
- Do not reuse the removed gasket.
- Do not push in the gasket while installing the center exhaust pipe assembly.
Connect the 3 exhaust pipe supports, and install the center exhaust pipe assembly.
- Install the 2 compression springs and 2 bolts.
-
Torque:
- 48 N*m{
489 kgf*cm
, 35 ft.*lbf
}
| 6.
INSTALL EXHAUST PIPE DAMPER |
 |
- Install the exhaust pipe damper with the 2 bolts.
-
Torque:
- 19 N*m{
194 kgf*cm
, 14 ft.*lbf
}
| 7.
INSTALL TAIL EXHAUST PIPE ASSEMBLY |
 |
- Using vernier calipers, measure the free length of the compression spring.
Minimum
|
40.5 mm (1.59 in.)
|
- HINT:
- If the length is less than the minimum, replace the compression spring.
- Using a plastic-faced hammer and wooden block, tap in a new gasket until its surface is flush with the center exhaust pipe assembly.
- NOTICE:
- Tap in the gasket in the correct direction.
- Do not reuse the removed gasket.
- Do not push in the gasket while installing the tail exhaust pipe assembly.
Connect the exhaust pipe support, and install the tail exhaust pipe assembly.
- Install the 2 compression springs and 2 bolts.
-
Torque:
- 48 N*m{
489 kgf*cm
, 35 ft.*lbf
}
| 8.
INSPECT FOR EXHAUST GAS LEAK |
 |
If exhaust gas is leaking, repair the leak. Replace damaged or worn parts as necessary.
| 9.
INSTALL NO. 2 ENGINE UNDER COVER
|
 |
- Install the No. 2 engine under cover with the 2 bolts.
| 10.
INSTALL NO. 1 ENGINE UNDER COVER
|
 |
- Install the No. 1 engine under cover with the 6 bolts and 2 clips.
| 11.
INSTALL ENGINE UNDER COVER ASSEMBLY
|
 |
- Install the engine under cover assembly with the 2 bolts, 2 screws and 5 clips.
- Install the engine under cover assembly RR with the 2 bolts.