DATA LIST / ACTIVE TEST
System information · Vehicles built from May 2007
| DATA LIST |
- HINT:
- Using the intelligent tester to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed.
- Reading the Data List information early in troubleshooting is one way to save diagnostic time.
- NOTICE:
- In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
Turn the ignition switch off.
Connect the intelligent tester to the DLC3.
Turn the ignition switch on (IG).
Turn the intelligent tester on.
Enter the following menus: Chassis / EMPS / Data List.
According to the display on the tester, read the "Data List".
EMPS: Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
Meter Vehicle Velocity
Vehicle speed from meter:
Min.: 0 km/h (0 mph)
Max.: 300 km/h (187.5 mph)
0 km/h (0 mph)
Vehicle stopped
No significant fluctuation
Vehicle driven at constant speed
Engine Revolution
Shows the engine speed:
Min.: 0 rpm
Max.: 12800 rpm
No significant fluctuation
Engine is running at a constant speed
Motor Actual Current
Amount of current to motor:
Min.: -327.68 A
Max.: 327.67 A
Value changes in proportion to steering effort
Power steering is in operation
Command Value Current
Demanded amount of current to motor:
Min.: -327.68 A
Max.: 327.68 A
Value changes in proportion to steering effort
Power steering is in operation
Steering Angle Velocity
Steering angle speed:
Min.: -32768°/sec.
Max.: 32767°/sec.
Value changes in proportion to steering effort
Steering wheel is turned
Thermistor Temperature
ECU substrate temperature:
Min.: -40°C
Max.: 150°C
-40 to 150°C
Ignition switch on (IG)
PIG Power Supply
Power source voltage to activate motor:
Min.: 0 V
Max.: 20.1531 V
11 to 14 V
Power steering is in operation
IG Power Supply
ECU power source voltage:
Min.: 0 V
Max.: 20.1531 V
11 to 14 V
Ignition switch on (IG)
Steering Torque
Steering wheel torque:
Min.: -7 Nm
Max.: 7 Nm
Value changes in proportion to steering effort
Ignition switch on (IG) and power steering is in operation
Motor Rotation Angle
Motor rotation angle:
Min.: 0°
Max.: 360°
During steering operation, motor rotation angle value changes from 0 to 360°
Power steering is in operation
Motor Voltage
Motor power supply voltage:
Min.:0 V
Max.: 45.955 V
11 to 14 V
Power steering is in operation
Motor Terminal Volt (U)
Motor terminal voltage (U phase):
Min.: 0 V
Max.: 46.667 V
When the steering wheel is turned, a voltage between 1 V and approximately 1 V less than the battery voltage is displayed.
Engine running and steering wheel is turned
Motor Terminal Volt (V)
Motor terminal voltage (V phase):
Min.: 0 V
Max.: 46.667 V
When the steering wheel is turned, a voltage between 1 V and approximately 1 V less than the battery voltage is displayed.
Engine running and steering wheel is turned
Motor Terminal Volt (W)
Motor Terminal voltage (W phase):
Min.: 0 V
Max.: 46.667 V
When the steering wheel is turned, a voltage between 1 V and approximately 1 V less than the battery voltage is displayed.
Engine running and steering wheel is turned
IG ON/OFF Times
Ignition switch ON/OFF number of times after fail detection:
Min.: 0 times
Max.: 65535 times
-
-
Motor Overheat Record
Continuous overheat prevention control record:
REC or UNREC
UNREC
-
Motor Lo Power Record
PIG power source voltage drop record:
REC or UNREC
UNREC
-
Eng Rev Inter Record
Record of engine revolution signal interruption
REC or UNREC
UNREC
-
Spd Sig Invalid Record
Record of vehicle speed signal invalid:
REC or UNREC
UNREC
-
Battery Voltage
Battery voltage:
Min.: 0 V
Max.: 25.5 V
11 to 14 V
-
PS Assist Signal
Power steering assist signal:
ON or OFF
ON: Power steering assist signal is sent
Ignition switch on (IG) and steering wheel is turned
OFF: Power steering assist signal is not sent
No steering load (in neutral position)
The Number of DTCs
Number of detected DTCs when freeze frame data stored:
Min.: 0
Max.: 255
-
-
| ACTIVE TEST |
- HINT:
- Using the intelligent tester to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.
Turn the ignition switch off.
Connect the intelligent tester to the DLC3.
Turn the ignition switch on (IG).
Turn the intelligent tester on.
Enter the following menus: Body / Combination Meter / Active Test.
According to the display on the tester, perform the "Active Test".
*1: w/o Multi-information DisplayCombination meter: Tester Display
Test Part
Control Range
Control Range
Indicat. EPS (*1)
P/S Warning Light
ON or OFF
Confirm that vehicle is stopped, engine idling
Master Warning (*2)
Master Warning Light
ON or OFF
Confirm that vehicle is stopped, engine idling
*2: w/ Multi-information Display