2007-2013 Highlander Kluger · Service Manual BODY ELECTRICAL

Display Signal Circuit between Navigation Receiver Assembly and Television Camera Assembly

Circuit diagnosis · Vehicles built from Jul 2010

Versions by build date: May 2007 – Jul 2008 Aug 2008 – Jun 2010 from Jul 2010

DESCRIPTION

The display signal from the television camera assembly is transmitted to the navigation receiver assembly.

WIRING DIAGRAM


w/ Navigation System (for DVD)
E210148E01

w/ Navigation System (for HDD)
E210148E02

INSPECTION PROCEDURE


1. CONFIRM MODEL
  1. Choose the model to be inspected.

    Result:
    Model
    Proceed to
    w/ Navigation system (for DVD)
    A
    w/ Navigation system (for HDD)
    B



B
Go to step 5
A


2. CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - TELEVISION CAMERA ASSEMBLY)
  1. Disconnect the E3 navigation receiver assembly.

  1. Disconnect the T16 television camera assembly.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    T16-2 (CV+) - E3-22 (V+)
    Always
    Below 1 Ω
    T16-4 (CB+) - E3-24 (CA+)
    Always
    Below 1 Ω
    T16-3 (CGND) - E3-21 (CGND)
    Always
    Below 1 Ω
    T16-1 (CV-) - E3-23 (V-)
    Always
    Below 1 Ω
    T16-2 (CV+) - Body ground
    Always
    10 kΩ or higher
    T16-4 (CB+) - Body ground
    Always
    10 kΩ or higher
    T16-3 (CGND) - Body ground
    Always
    10 kΩ or higher
    T16-1 (CV-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3. INSPECT NAVIGATION RECEIVER ASSEMBLY

  1. E153726E18
    Reconnect the E3 navigation receiver assembly.
    Text in Illustration 
    *a
    Component with harness connected
    (Navigation Receiver Assembly)

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    E3-24 (CA+) - E3-21 (CGND)
    Ignition switch ON
    Shift lever in R
    5.5 to 7.05 V



NG
REPLACE NAVIGATION RECEIVER ASSEMBLY (Click here)
OK


4. INSPECT TELEVISION CAMERA ASSEMBLY
  1. Reconnect the T16 television camera assembly.

  1. E210150E01
    Check that the E6 and E3 connectors are connected to the navigation receiver assembly.
    Text in Illustration 
    *a
    Component with harness connected
    (Navigation Receiver Assembly)

  1. E171712E14
    Check the waveform of the television camera assembly using an oscilloscope.

    HINT:
    A waterproof connector is used for the rear television camera assembly. Therefore, inspect the waveform at the navigation receiver assembly with the connector connected.

    OK:
    Waveform is similar to that shown in the illustration.

    Item
    Content
    Terminal No. (Symbol)
    E3-22 (V+) - E6-7 (GND)
    Tool Setting
    200 mV/DIV., 50 μsec./DIV.
    Condition
    Ignition switch ON, shift lever in R

    HINT:
    The video waveform changes according to the image sent by the television camera assembly.

    Text in Illustration 
    *a
    Waveform 1 (camera lens not covered, displaying an image)
    *b
    Waveform 2 (camera lens covered, blacking out the screen)
    *c
    Synchronization Signal
    *d
    Video Waveform



NG
REPLACE TELEVISION CAMERA ASSEMBLY (Click here)
OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)

5. CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - TELEVISION CAMERA ASSEMBLY)
  1. Disconnect the E2 navigation receiver assembly.

  1. Disconnect the T16 television camera assembly.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    T16-2 (CV+) - E2-1 (V+)
    Always
    Below 1 Ω
    T16-4 (CB+) - E2-2 (CA+)
    Always
    Below 1 Ω
    T16-3 (CGND) - E2-12 (CGND)
    Always
    Below 1 Ω
    T16-1 (CV-) - E2-11 (V-)
    Always
    Below 1 Ω
    T16-2 (CV+) - Body ground
    Always
    10 kΩ or higher
    T16-4 (CB+) - Body ground
    Always
    10 kΩ or higher
    T16-3 (CGND) - Body ground
    Always
    10 kΩ or higher
    T16-1 (CV-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6. INSPECT NAVIGATION RECEIVER ASSEMBLY

  1. E210152E01
    Reconnect the E2 navigation receiver assembly.
    Text in Illustration 
    *a
    Component with harness connected
    (Navigation Receiver Assembly)

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    E2-2 (CA+) - E2-12 (CGND)
    Ignition switch ON
    Shift lever in R
    5.5 to 7.05 V



NG
REPLACE NAVIGATION RECEIVER ASSEMBLY (Click here)
OK


7. INSPECT TELEVISION CAMERA ASSEMBLY
  1. Reconnect the T16 television camera assembly.

  1. E210151E01
    Check that the E6 and E2 connectors are connected to the navigation receiver assembly.
    Text in Illustration 
    *a
    Component with harness connected
    (Navigation Receiver Assembly)

  1. E171712E14
    Check the waveform of the television camera assembly using an oscilloscope.

    HINT:
    A waterproof connector is used for the rear television camera assembly. Therefore, inspect the waveform at the navigation receiver assembly with the connector connected.

    OK:
    Waveform is similar to that shown in the illustration.

    Item
    Content
    Terminal No. (Symbol)
    E2-1 (V+) - E6-7 (GND)
    Tool Setting
    200 mV/DIV., 50 μsec./DIV.
    Condition
    Ignition switch ON, shift lever in R

    HINT:
    The video waveform changes according to the image sent by the television camera assembly.

    Text in Illustration 
    *a
    Waveform 1 (camera lens not covered, displaying an image)
    *b
    Waveform 2 (camera lens covered, blacking out the screen)
    *c
    Synchronization Signal
    *d
    Video Waveform



NG
REPLACE TELEVISION CAMERA ASSEMBLY (Click here)
OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)


← Display Signal Circuit between Navigation Receiver Assembly and Television Camera Assembly (Aug 2008 – Jun 2010)PRECAUTION (May 2007 – Jul 2008) →