2007-2013 Highlander Kluger · Service Manual ENGINE

INSTALLATION

Removal / installation · Vehicles built Aug 2008 – Jun 2010

Versions by build date: May 2007 – Jul 2008 Aug 2008 – Jun 2010 from Jul 2010


1. INSTALL ENGINE SWITCH

  1. A170658
    Engage the 2 claws to install the switch.

  1. Connect the switch connector.


2. INSTALL FRONT NO. 1 CONSOLE BOX INSERT (for LHD)

  1. B168373
    Engage the claw and 2 guides.

  1. Install the front No. 1 console box insert with the 3 screws <F> and 2 clips.


3. INSTALL FRONT NO. 2 CONSOLE BOX INSERT (for RHD)

  1. B173038
    Engage the claw and 2 guides.

  1. Install the front No. 2 console box insert with the 3 screws <F> and clip.


4. INSTALL CONSOLE BOX ASSEMBLY (w/ Rear Air Conditioning System)

  1. B175149
    Engage the 6 claws.

  1. Connect the connector.

  1. B181135
    Install the console box assembly with the 4 bolts and 2 screws.


5. INSTALL CONSOLE BOX ASSEMBLY (w/o Rear Air Conditioning System)

  1. B173629
    Engage the 6 claws.

  1. B173628
    Install the console box assembly with the 4 bolts and 2 screws.


6. INSTALL LOWER REAR CONSOLE BOX
  1. Install the lower rear console box.


7. INSTALL NO. 2 CONSOLE BOX DUCT (w/o Rear Air Conditioning System)

  1. B173013
    Install the No. 2 console box duct as shown in the illustration.


8. INSTALL UPPER CONSOLE PANEL SUB-ASSEMBLY

  1. B168372
    Connect the connector.

  1. Engage the 4 claws and 4 clips, and install the upper console panel sub-assembly.


9. INSTALL LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY (for Automatic Air Conditioning System)

  1. B173009
    Connect the hood lock control cable assembly.

  1. Connect each connector and the aspirator duct.

  1. B173021
    Engage the 3 claws and 10 clips.

  1. Install the lower instrument panel finish panel sub-assembly with the 2 bolts <B>.


10. INSTALL LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY (for Manual Air Conditioning System)

  1. B168371
    Connect the hood lock control cable assembly.

  1. Connect each connector.

  1. Engage the 3 claws and 10 clips.

  1. Install the lower instrument panel finish panel sub-assembly with the 2 bolts <B>.


11. INSTALL COWL SIDE TRIM SUB-ASSEMBLY LH

  1. B173227
    Engage the claw and clip, install the cowl side trim sub-assembly LH.

  1. Install the clip.


12. INSTALL FRONT DOOR SCUFF PLATE LH

  1. B173224
    Engage the guide and the 8 claws, and install the front door scuff plate LH.


13. INSTALL AIR CONDITIONING CONTROL ASSEMBLY (for Automatic Air Conditioning System)
  1. Connect the connector.

  1. E150367
    Engage the 4 clips and install the air conditioning control assembly.


14. INSTALL HEATER CONTROL AND ACCESSORY ASSEMBLY (for Manual Air Conditioning System)
  1. Connect the connector.

  1. E150368
    Engage the 4 clips and install the heater control and accessory assembly.


15. INSTALL CENTER INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY (w/ Smart Entry and Start System)

  1. B184681E01
    Apply protective tape to the areas shown in the illustration.

  1. Connect each connector.

  1. Engage the 10 claws and 8 clips, and install the center instrument cluster finish panel assembly.

    NOTICE:
    Do not the damage the instrument panel safety pad assembly and lower instrument panel finish panel sub-assembly.


16. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).

← INSTALLATION (May 2007 – Jul 2008)INSTALLATION (from Jul 2010) →