2007-2013 Highlander Kluger · Service Manual ENGINE

Power Source Mode does not Change

Circuit diagnosis · Vehicles built May 2007 – Jul 2008

Versions by build date: May 2007 – Jul 2008 Aug 2008 – Jun 2010 from Jul 2010

DESCRIPTION

When the engine switch is pushed with the electrical key in the cabin, the main body ECU receives signals to switch the power source mode.

HINT:
To allow use of the intelligent tester to inspect the push-button starting function when the engine switch is off, repeat opening and closing any of the doors. Opening and closing a door establishes communication between the intelligent tester and the main body ECU. (Opening and closing a door can also be simulated by operating a door courtesy light switch.)


WIRING DIAGRAM

B177113E02
B177114E04

INSPECTION PROCEDURE


1. CHECK SMART ENTRY AND START SYSTEM

  1. Remove the battery of the electrical key transmitter (Click here).B178268E01

  1. Touch the logo side of the key or card key to the engine switch.

  1. Check that power source mode can be changed to on (IG and ACC).

    Result:
    Result
    Proceed to
    Power source mode does not change to on (ACC)
    A
    Power source mode does not change to on (IG)
    B
    Power source mode does not change to on (IG and ACC)
    C
    Power source mode is turned on
    D



B
Go to step 4

C
Go to step 10

D
GO TO SMART ENTRY AND START SYSTEM (ENTRY) (Click here)
A


2. INSPECT ACC RELAY

  1. B016200E23
    Remove the ACC relay from the instrument panel junction block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified condition
    3 - 5
    When battery voltage is not applied to terminals 1 and 2
    10 kΩ or higher
    3 - 5
    When battery voltage is applied to terminals 1 and 2
    Below 1 Ω



NG
REPLACE ACC RELAY
OK


3. CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - INSTRUMENT PANEL JUNCTION BLOCK)

  1. Disconnect the D7 connector from the main body ECU.B138001E37

  1. Disconnect the 1I connector from the instrument panel junction block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified condition
    D7-22 (ACCD) - 1I-3
    Always
    Below 1 Ω
    D7-22 (ACCD) or 1I-3 - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE MAIN BODY ECU (INSTRUMENT PANEL JUNCTION BLOCK)

4. INSPECT IG1 RELAY

  1. A092673E45
    Remove the IG1 relay from the instrument panel junction block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester connection
    Condition
    Specified condition
    3 - 5
    When battery voltage is not applied to terminals 1 and 2
    10 kΩ or higher
    3 - 5
    When battery voltage is applied to terminal 1 and 2
    Below 1 Ω



NG
REPLACE IG1 RELAY
OK


5. CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - INSTRUMENT PANEL JUNCTION BLOCK)

  1. Disconnect the D7 connector from the main body ECU.B138001E38

  1. Disconnect the 1I connector from the instrument panel junction block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester connection
    Condition
    Specified condition
    D7-3 (IG1D) - 1I-9
    Always
    Below 1 Ω
    D7-3 (IG1D) or 1I-9 - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6. INSPECT IG2 RELAY

  1. B016200E23
    Remove the IG2 relay from the engine room relay block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester connection
    Condition
    Specified condition
    3 - 5
    When battery voltage is not applied to terminals 1 and 2
    10 kΩ or higher
    3 - 5
    When battery voltage is applied to terminal 1 and 2
    Below 1 Ω



NG
REPLACE IG2 RELAY
OK


7. CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - IG2 RELAY)

  1. Disconnect the D6 connector from the main body ECU.B176772E02

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester connection
    Condition
    Specified condition
    D6-11 (IG2D) - Engine room relay block IG2 relay terminal 1
    Always
    Below 1 Ω
    D6-11 (IG2D) or Engine room relay block IG2 relay terminal 1 - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


8. CHECK HARNESS AND CONNECTOR (BATTERY - IG2 RELAY)

  1. B177331E01
    Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester connection
    Condition
    Specified condition
    Engine room relay block IG2 relay terminal 5 - Body ground
    Always
    11 to 14 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR, OR REPLACE IG2 FUSE
OK


9. CHECK HARNESS AND CONNECTOR (IG2 RELAY - BODY GROUND)

  1. B177331E01
    Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester connection
    Condition
    Specified condition
    Engine room relay block IG2 relay terminal 2 - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE MAIN BODY ECU (INSTRUMENT PANEL JUNCTION BLOCK)

10. CHECK HARNESS AND CONNECTOR (BATTERY - INSTRUMENT PANEL JUNCTION BLOCK)

  1. B177332E02
    Disconnect the 1A connector from the instrument panel junction block.

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester connection
    Condition
    Specified condition
    1A-1 - Body ground
    Always
    11 to 14 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR, OR REPLACE ALT FUSE
OK


11. CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK - BODY GROUND)

  1. B177333E02
    Disconnect the 1F connector from the instrument panel junction block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester connection
    Condition
    Specified condition
    1F-10 - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPAIR OR REPLACE HARNESS OR CONNECTOR


← B2289 Key Collation Waiting Time Over (from Jul 2010)Power Source Mode does not Change (Aug 2008 – Jun 2010) →